Instrukcja obsługi Denver CAP-4300

Denver odbiornik CAP-4300

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Denver CAP-4300 (10 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/10
HIGH EFFICIENCY POWER AMPLIFIER
OWNER'S MANUAL
CAR AUDIO SYSTEM
PLEASE READ CAREFULLY BEFORE INSTALLING OR OPERATING THIS UNIT
CAP-4300
WARNING
Make sure you choose a suitable place to mount the unit. The position should be completely dry
with a good circulation of air, and from a mechanical point of view very stable.
ENG-1
System planning
Proper system planning is the best way to
maximize your amplifier performance. By
planning your installation carefully you can
avoid situations where the performance of the
reliability of your system is compromised. Your
authorized dealer has been trained to
maximize your system's sonic potential. Your
dealer is a valuable resource in helping you
with your system design and installation.
Speaker requirements
Each channel of your amplifier can easily drive
4 speaker loads when used in the stereo Ω
mode. When a channel-pair is bridged, the
recommended minimum load impedance is 3 Ω
for subwoofer use, and 4 for full range Ω
operation. Although operation with lower
impedances is not likely to cause immediate
damage to the internal circuitry, the unit will
most likely overheat, causing the thermal
protection circuitry to shut down the amplifier.
When the chassis cools down, normal
operation will resume. Continuing to operate
the amplifier under these conditions is not
recommended and will reduce its life
expectancy.
Most speakers designed for car audio
operation are 4 impedance. Connecting two Ω
such speakers in parallel will result in a 2 Ω
impedance load as seen by the amplifier.
Some subwoofer models feature a dual 4 Ω
voice coil design. Connecting these voice coils
in parallel will result in a 2 nominal Ω
impedance, which is not recommended for use
with bridged channels of your amplifier.
Series wiring
Parallel wiring
Series/parallel wiring
ENG-2
Power Connection Leads
Notes on the power supply
Connect the + 12V power input lead only after all other leads have been connected.
Be sure to connect the ground wire of the unit securely to a metal part of the car.
A lose connection may cause a malfunction of the amplifier.
REMOTE: The unit is turned on by applying + 12Volts to this terminal This terminal dose
not draw heavy current like the two power terminal so a thinner connecting wire is
acceptable. Standard 18 GAUGE is fine and the standard colour is yellow. If the radio is
equipped with a power antenna control wire, it can drive this terminal. If the power
antenna wire is already in use, you can still splice into it. With this method, the unit will
turn on automatically with the radio. Use the power supply lead with a fuse attached
whose value is the same as original fuse.
Place the fuse in the power supply lead as close as possible to the car battery.
During a full power operation, Maximum current will run through the system. Therefore,
Make sure that the leads to be connected to the + 12v and GND terminals of the unit
respectively must be larger than 10-Gauge (AWG. 10).

Specyfikacje produktu

Marka: Denver
Kategoria: odbiornik
Model: CAP-4300

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Denver CAP-4300, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje odbiornik Denver

Denver

Denver CAP-4300 Instrukcja

6 Września 2024
Denver

Denver CAP-4320 Instrukcja

31 Sierpnia 2024
Denver

Denver DMB-113CI Instrukcja

20 Sierpnia 2024
Denver

Denver DTB-133 Instrukcja

15 Sierpnia 2024

Instrukcje odbiornik

Najnowsze instrukcje dla odbiornik

Marantz

Marantz SR-8000 Instrukcja

15 Stycznia 2025
AKAI

AKAI AM-32 Instrukcja

15 Stycznia 2025
Peavey

Peavey CKd 608 Instrukcja

15 Stycznia 2025
OSD Audio

OSD Audio Nero HTX4150 Instrukcja

14 Stycznia 2025
S.M.S.L

S.M.S.L PA200 Instrukcja

14 Stycznia 2025
Pyle

Pyle PFMRA340BB.5 Instrukcja

13 Stycznia 2025
Wavtech

Wavtech link700.4plus Instrukcja

13 Stycznia 2025
Behringer

Behringer NU6000DSP Instrukcja

12 Stycznia 2025
Denon

Denon DRA-935R Instrukcja

12 Stycznia 2025
Kenwood

Kenwood KMM-BT508DAB Instrukcja

12 Stycznia 2025