Instrukcja obsługi DENSO GT10B-SB

DENSO czytnik kodów kreskowych GT10B-SB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DENSO GT10B-SB (144 stron) w kategorii czytnik kodów kreskowych. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/144
Bar Code Handy Scanner
GT10B-SB
GT10B-LB
User's Manual
DENSO WAVE INCORPORATED does not assume any product liability arising out of, or in connection with,
the application or use of any product, circuit, or application described herein.
If it is judged by DENSO WAVE INCORPORATED that malfunction of the product is due to the product
having been dropped or subjected to impact, repairs will be made at a reasonable charge even within the
warranty period.
Intellectual Property Precaution
DENSO WAVE INCORPORATED ("DENSO WAVE") takes reasonable precautions to ensure its products do
not infringe upon any patent of other intellectual property rights of other(s), but DENSO WAVE cannot be
responsible for any patent or other intellectual property right infringement(s) or violation(s) which arise from (i)
the use of DENSO WAVE's product(s) in connection or in combination with other component(s), product(s),
data processing system(s) or equipment or software not supplied from DENSO WAVE; (ii) the use of DENSO
WAVE's products in a manner for which the same were not intended nor designed; or (iii) any modification of
DENSO WAVE's products by other(s) than DENSO WAVE.
Limited Warranty on Software Products
In no event will DENSO WAVE be liable for direct, indirect, special, incidental, or consequential damages
(including imaginary profits or damages resulting from interruption of operation or loss of business
information) resulting from any defect in the software or its documentation or resulting from inability to apply
the software or its documentation.
Bluetooth® is a trademark owned by its proprietor. DENSO WAVE uses Bluetooth
® wireless technology under
license.
Copyright © DENSO WAVE INCORPORATED, 2008, 2007, 2005, 2004
All rights reserved. No part of this publication may be reproduced in any form or by any means without permission in
writing from the publisher.
All products and company names mentioned in this manual are trademarks or registered trademarks of their respective
holders.
Specifications are subject to change without prior notice.
FCC and RSS-210 Regulations
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device complies with Part 15 of the FCC Rules and RSS-210 Rules
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Radio Frequency Exposure
This device meets the FCC RF Exposure Guidelines in OET65.
This transmitter and its antenna should not be placed next to other antennas or similar radiating structure.
ICES-003 Regulation
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Specyfikacje produktu

Marka: DENSO
Kategoria: czytnik kodów kreskowych
Model: GT10B-SB

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z DENSO GT10B-SB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje czytnik kodów kreskowych DENSO

DENSO

DENSO GT10B-SB Instrukcja

17 Września 2024
DENSO

DENSO QS20H-I-U Instrukcja

16 Września 2024
DENSO

DENSO GT10B-SM Instrukcja

16 Września 2024
DENSO

DENSO GT10-SM Instrukcja

16 Września 2024
DENSO

DENSO HC36 Instrukcja

16 Września 2024

Instrukcje czytnik kodów kreskowych

Najnowsze instrukcje dla czytnik kodów kreskowych

Posiflex

Posiflex CD-3602U Instrukcja

9 Października 2024
Posiflex

Posiflex CD-3202U Instrukcja

9 Października 2024
Datalogic

Datalogic CBX500 Instrukcja

9 Października 2024
Brady

Brady IRX200 Instrukcja

8 Października 2024
Newland

Newland HR33 Marlin filaire Instrukcja

8 Października 2024
Wasp

Wasp WDI9600 Instrukcja

7 Października 2024
Wasp

Wasp WLS9500 Instrukcja

7 Października 2024
Wasp

Wasp WCS3900 Instrukcja

7 Października 2024
Wasp

Wasp WDI4600 Instrukcja

7 Października 2024
Wasp

Wasp WLR8900 Instrukcja

7 Października 2024