Instrukcja obsługi DENSO GT10-SM

DENSO czytnik kodów kreskowych GT10-SM

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DENSO GT10-SM (92 stron) w kategorii czytnik kodów kreskowych. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/92

Bar Code Handy Scanner

GT10B-SM / GT11B-SM

GT10B-LM

User's Manual

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which case the

user may be required to take adequate measures.

FCC Regulations

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired

operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the interference at his own expense.

 DENSO WAVE INCORPORATED does not assume any product liability arising out of, or in connection with,

the application or use of any product, circuit, or application described herein.

 If it is judged by DENSO WAVE INCORPORATED that malfunction of the product is due to the product

having been dropped or subjected to impact, repairs will be made at a reasonable charge even within the

warranty period.

 Intellectual Property Precaution

DENSO WAVE INCORPORATED ("DENSO WAVE") takes reasonable precautions to ensure its products do

not infringe upon any patent of other intellectual property rights of other(s), but DENSO WAVE cannot be

responsible for any patent or other intellectual property right infringement(s) or violation(s) which arise from (i)

the use of DENSO WAVE's product(s) in connection or in combination with other component(s), product(s),

data processing system(s) or equipment or software not supplied from DENSO WAVE; (ii) the use of DENSO

WAVE's products in a manner for which the same were not intended nor designed; or (iii) any modification of

DENSO WAVE's products by other(s) than DENSO WAVE.

writing from the publisher.

All products and company names mentioned in this manual are trademarks or registered trademarks of their respective

holders.

Specifications are subject to change without prior notice.

Contents

Preface ............................................................................................................................................................................. i

SAFETY PRECAUTIONS.............................................................................................................................................. ii

Care and Maintenance ..................................................................................................................................................... v

Chapter 1 Parts Names and Functions.......................................................................................................................... 1

Chapter 2 Preparation ................................................................................................................................................... 2

2.1 Connecting the Interface Cable to the Scanner ........................................................................................... 2

2.2 Connecting the Scanner to Your Computer ................................................................................................ 3

Chapter 3 Reading Bar Codes ...................................................................................................................................... 5

Chapter 4 Customizing the Scanner ............................................................................................................................. 7

Chapter 5 Scanning Control ......................................................................................................................................... 8

5.1 Trigger Switch Control................................................................................................................................ 8

5.2 Software Control ......................................................................................................................................... 9

5.3 Auto Sensing Mode—Automatic Detection of Labels ............................................................................... 11

Chapter 6 Magic Key Control ...................................................................................................................................... 12

Chapter 7 Scanning Functions...................................................................................................................................... 14

7.1 Data Verification Mode ............................................................................................................................... 14

7.1.1 Verification setup procedure ................................................................................................................. 14

7.1.2 Verification conditions .......................................................................................................................... 16

7.1.3 Verification result output....................................................................................................................... 17

7.1.4 Output of the master data registered...................................................................................................... 17

7.2 Specifying the Numbers of Digits of Standard 2of5 and Interleaved 2of5 Symbols to Read,

by Scanning Bar Codes ............................................................................................................................... 18

Chapter 8 Data Editing ................................................................................................................................................. 19

8.1 Extracting Data............................................................................................................................................ 19

8.2 Substituting Data ......................................................................................................................................... 20

8.3 Blocksorting Data........................................................................................................................................ 21

8.4 Parenthesizing AIs (Application Identifier) in EAN-128 Data................................................................... 22

8.5 Extracting AI (Application Identifier)-Prefixed Strings from EAN-128 Data ........................................... 22

8.6 Data Editing Notes ...................................................................................................................................... 23

8.6.1 Data edit conditions ............................................................................................................................... 23

8.6.2 Rules for data editing............................................................................................................................. 23

8.6.3 AI table................................................................................................................................................... 24

Chapter 9 Beeper, Indicator LED and Vibrator ........................................................................................................... 29

9.1 Beeper.......................................................................................................................................................... 29

9.2 Indicator LED.............................................................................................................................................. 31

9.3 Vibrator ........................................................................................................................................................ 32