Instrukcja obsługi Code Corporation CodeXML M3

Code Corporation Karta sieciowa/adapter CodeXML M3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Code Corporation CodeXML M3 (2 stron) w kategorii Karta sieciowa/adapter. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Connecting with QuickConnect Code
Scan the QuickConnect Code on the label of the CodeXML M3 Bluetooth® Modem using
the Code Reader with which you wish to establish a paired connection. The reader and
computer should connect within 10 seconds. The reader will beep once as confi rmation,
the modem’s LED light will become solid once the connection is established. If the reader
does not connect, the reader will beep four times in rapid succession.
English (Default) Universal French German
CodeXML M3 Bluetooth® Modem Installation as a USB Keyboard
Figure 3
Cable Installation
Attach the end of the USB cable to the CodeXML M3 Bluetooth® Modem (Figure 2). Plug
the USB connector into the USB port on the computer (Figure 3). Once plugged in the
modem’s blue LED light will fl ash.
Figure 2
Establish Mode
Establish connection (see above), then scan the USB Mode code
(M708_01). Scan the QuickConnect Code again. You are ready to begin
reading bar codes and transmitting data to the computer.
USB Cable installed to
CodeXML M3 Bluetooth® Modem
USB Mode
Non-printable ASCII
Keyboard (Crtl + character)
Japanese Non-printable ASCII Keyboard
(No Leading 0)
Keyboard Input (USB)
The modem is defaulted to English language keyboards. If you need to communicate in a
different language requiring a change in keyboard settings, please scan the appropriate
code below, after connecting to the modem:
CodeXML M3 Blueooth® Modem Installation as a RS-232 (Serial)
Figure 4 Figure 5 Figure 6 Figure 7
Cable Installation
Attach the end of the RS-232 cable to the CodeXML M3 Bluetooth® Modem
(Figure 4). Connect the RS-232 adapter to the back of the computer (Figure 5).
Connect the RS-232 cable to the power supply (Figure 6). Plug the power supply into
a wall socket (Figure 7). Once connected the Modem’s blue LED light will turn on.
RS-232 Cable (Left), CodeXML M3
Bluetooth® Modem (Center), Power
Supply (Right)
Change Baud Rate Settings: Scan the appropriate code below, after connecting to
the modem:
Note: Codes only affect Baud Rate for the modem and do not affect any settings on Code Readers.
9600 (Default) 19200 38400
57600 115200
Default Modem
settings:
Baud Rate: 9600
Stop Bits: 8
Parity: None
Stop Bits: 1
Hardware: None
Connecting with QuickConnect Code
See instructions on page 2 for establishing a Bluetooth connection between the modem
and the reader.
Establish Mode
Establish connection (see page 2), then scan the RS-
232 Mode code (M661_01). Scan the QuickConnect
Code again. You are ready to begin reading bar codes
and transmitting data to the computer.
RS-232 Mode
2 C003996_03_CodeXML_M3_Modem_Quickstart C003996_03_CodeXML_M3_Modem_Quickstart 3
Quickstart Guide
4 C003996_03_CodeXML_M3_Modem_Quickstart
CodeXML M3 Bluetooth® Modem -
Multiple Interface Unit (MIU)
C003996_03_CodeXML_M3_Modem_Quickstart 1
The CodeXML M3 Bluetooth® MIU Modem is an external PC accessory designed
to be connected to a computer for use with a Code Reader (CR2 or CR3). The
Modem enables a reader to wirelessly transmit data to the computer without
installing any software or drivers. The Modem can accommodate USB and RS-232
(Serial) cables (Figure 1).
Figure 1
The CodeXML M3 Bluetooth® Modem is ‘plug & play.’ You simply plug-in the Modem,
scan the QuickConnect code on the Modem label and start transmitting data from
Code Readers without downloading any drivers or software. The Modem can receive
Bluetooth signals from up to 300 feet (100 meters) away.
For assistance, contact Code Technical Support at: (801) 495 2200; or by email:
support@codecorp.com
CodeXML M3 Bluetooth® Modem
VVVVvvvvCKPE BaudString:
VVVV 4 digit fi rmware version
vvvv Not Applicable to the CodeXML M3 Bluetooth Modem
C 1 digit comm mode: 1=RS-232, 2=Wand Emul., 3=USB
KBD
K Keyboard Map, same as reader host ICD setting 0x2d
P 1 digit packet protocol: 0=Raw, 1=SPX packet, 2=Code
Reader packet
E Pre-emptible Mode
1=enabled, 0=off/disabled
M Max Packet Sized (Firmware version 1080 and Higher)
1= enabled, 0=off/disabled
BaudString spx: Baud:DataBitsParityStopbits
For All Readers:
Scan to View
Firmware Version
Modem Firmware Version Output & Values (for reference only):
The CodeXML M3 Bluetooth® Modem has been tested for compliance with FCC and CE
regulations and was found to be compliant with all applicable FCC Rules and Regulations.
FCC ID#: QQ6-XML02
Model #: BTHDG-M3-RO-CX
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes made by the user not approved by Code Corporation can void the user’s authority
to operate the equipment.
To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation of 20 cm
or more should be maintained between the antenna of this device and persons during device
operation. To ensure compliance, operations at closer than this distance are not recommended.
The antenna used for this transmitter must not be co-located in conjunction with any other
antenna or transmitter.
CodeXML M3 Bluetooth® Modem
Important Note:
US Patent: US 7,240,831, Patents Pending.

Specyfikacje produktu

Marka: Code Corporation
Kategoria: Karta sieciowa/adapter
Model: CodeXML M3

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Code Corporation CodeXML M3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Karta sieciowa/adapter Code Corporation

Code Corporation

Code Corporation CodeXML M3 Instrukcja

25 Września 2024
Code Corporation

Code Corporation CodeXML M2 Instrukcja

25 Września 2024

Instrukcje Karta sieciowa/adapter

Najnowsze instrukcje dla Karta sieciowa/adapter

Vigitron

Vigitron Vi3305 Instrukcja

10 Grudnia 2024
LevelOne

LevelOne FNC-0109TX Instrukcja

14 Października 2024
StarTech.com

StarTech.com ST1000SPEX2T Instrukcja

9 Października 2024
StarTech.com

StarTech.com ST1000SPEX2LT Instrukcja

9 Października 2024
StarTech.com

StarTech.com AF221CE-POE-INJECTOR Instrukcja

9 Października 2024
StarTech.com

StarTech.com USB3LINK Instrukcja

9 Października 2024
StarTech.com

StarTech.com PCMACLINK2 Instrukcja

9 Października 2024
StarTech.com

StarTech.com PEX1000SFP Instrukcja

9 Października 2024
StarTech.com

StarTech.com ST2GPEX Instrukcja

9 Października 2024
StarTech.com

StarTech.com USB56KEM2 Instrukcja

9 Października 2024