Instrukcja obs艂ugi Cobra CM 300-004
Przeczytaj poni偶ej 馃摉 instrukcj臋 obs艂ugi w j臋zyku polskim dla Cobra CM 300-004 (1 stron) w kategorii Marifoon. Ta instrukcja by艂a pomocna dla 7 os贸b i zosta艂a oceniona przez 2 u偶ytkownik贸w na 艣rednio 4.5 gwiazdek
Strona 1/1
NYLON RATCHET MOUNT ASSEMBLY
4
Check
your
parts
list
( see
picture
diagram )
Parts
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Description
2 1
/2"
hex
bolt
lever
bar
rotation
hub
rotation
mount
lock
washer
for
hex
bolt
# 1
nut
for
hex
bolt
# 1
nut
for
hex
bolt
# 10
lock
washer
for
hex
bolt
# 10
base plate
2"
hex
bolt
mounting
hardware
for
base plate:
( 4 pieces each: 1/2" bolts,
lock
washers,
flat
washers
and
nuts)
Step
1.
A. Slide the
hex
bolt
(10)
through
the
flat
side
of
the
rotation
hub
(3) and
into
the
adjusting
side
of
the base plate (9).
B. Place
lock
washer
(8) and
nut
(7)
on
the bolt.
Only
hand
tighten
at
this
time.
Step
2.
A. Slide the
hex
bolt
(1)
through
the indented hole
side
of
the
lever
bar
(2) and
continue
through
the
adjusting
side
of
the
rotation
hub
(3).
B. With the lever
bar
(2) in vertical
position,
screw
the
hex
bolt
(1)
into
rotation
mount
(4)
all the
way
in. Then
back
the hex
bolt
(1)
out
1-1
3/4
turns.
C.
Place
lock
washer
(5) and
nut
(6) on the
hex
bolt
(1) and
tighten
the
nut
(6)
while
holding
the hex
b9lt
(1
).
D.
Tighten
the
assembly
by
moving
the
lever
bar
(2)
counter
clockwise.
Step
3.
A. To lay
your
antenna
over
(fold down),
simply
turn
the
lever
bar
(2)
clockwise.
This
will
release the rotation
hub
from
mount
and
allow
you
to
move
the antenna
to
the horizontal
position.
If
bolt
(1) is
too
loose,
your
antenna
could
fall
over
when the lever
is
released.
If
bolt
(1) is
too
tight
your
antenna
may
not
fold
over. To
adjust
this,
hold
the
bolt
in
position
and
loosen
nut
(6). To
adjust
for
a
too
loose
condition,
screw
bolt
(1) in
about
1/4-1/2 turn. Once adjusted,
hold
bolt
(1) in a
steady
position
and
tighten
nut
(6). Reverse
this
process
if
bolt
(1)
is
to
tight.
Specyfikacje produktu
| Marka: | Cobra |
| Kategoria: | Marifoon |
| Model: | CM 300-004 |
Potrzebujesz pomocy?
Je艣li potrzebujesz pomocy z Cobra CM 300-004, zadaj pytanie poni偶ej, a inni u偶ytkownicy Ci odpowiedz膮
Instrukcje Marifoon Cobra
6 Lipca 2024
Instrukcje Marifoon
Najnowsze instrukcje dla Marifoon
14 Wrze艣nia 2024
9 Wrze艣nia 2024
1 Wrze艣nia 2024
20 Sierpnia 2024
17 Sierpnia 2024
4 Lipca 2024