Instrukcja obsługi Citronic CASA-10BA

Citronic subwoofer CASA-10BA

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Citronic CASA-10BA (4 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
CASA
Active Subwoofer Cabinets
Item ref: CASA-10BA 178.120UK
CASA-12BA 178.122UK
CASA-15BA 178.125UK
CASA-18BA 178.128UK
User Manual
Version 1.1
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
CASA active subwoofers User Manual
Introduction
Thank you for choosing a CASA active subwoofer as part of your sound system.
This product is designed to enhance a full-range sound system with powerful sub-frequencies and transients.
Please read this manua to achieve optimum performance from your s cabinet and avoid damage through misuse. l ub
Package Contents
• CASA- ries active subwoofer se
• Mains lead(s)
• User manual
If you find any part is missing or the product has arrived with any problems, please contact your retailer at once.
This product contains no user-serviceable parts, so make no attempt to try to fix or modify this item yourself as this will
invalidate the warranty. We recommend you keep the original package and proof of purchase for any possible
replacement or return issues.
Warning
To prevent the risk of fire or electric shock, do not expose any of the components to rain or moisture.
Avoid impact to any of the components.
No user serviceable parts inside - refer servicing to qualified service personnel.
Safety
• Please observe the following warning conventions
CAUTION: RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates that dangerous voltage constituting a risk of electric shock
is present within this unit
This symbol indicates that there are important operating and maintenance
instructions in the literature accompanying this unit.
• Ensure that the correct mains lead is used with adequate current rating and mains voltage is as stated on the un it
• Avoid ingress of water or particles into any part of the housing If liquids are spilled on the cabinet, stop using .
immediately, allow the unit to dry out and have checked by qualified personnel before further use
Warning: this unit must be earthed
Placement
• Keep the electronic parts out of direct sunlight and away from heat sources.
• Position the cabinet on a stable surface that is adequate to support the weight of the product.
• Allow adequate space for cooling and access to controls and connections at the rear of the cabine t.
• Keep the cabinet away from damp or dusty environments.
Cleaning
• Use a soft dry or slightly damp cloth clean surfaces of the cabinet to
• A soft brush can be used to clear debris from controls and connections without damaging them
• To avoid damage, not use solvents to clean any parts of the cabinet. do
CASA active subwoofers User Manual
Rear panel layout
Setting up
Position your CASA active subwoofer( on a stable surface capable of supporting the load and vibrations from the s)
cabinet. For maximum sound delivery, position with the back close to a solid wall or in a corner of the room.
Aim the cabinet towards the audience or listeners and not in direct line of sight with any microphones that are connected
to the sound system. This is t void feedback (howling or booming caused by the microphone hearingo a “ ” itse amplifielf d).
Also, keep microphone stands away from the subwoofer to avoid vibrations being transferred to the microphones.
If a single CA active subwoofer is to be used with a stereo pair of active full-range speakers, connect both Left and SA
Right outputs from the mixer into the Left + Right inputs of the CASA active subwoofer (1) .
For maximum efficiency, Connect the Left Right OUTPUT XLRs (3) to each full range speaker, which removes the +
lowest frequencies that are being delivered by the subwoofer, freeing up the power of the full-range top cabinets to
produce upper frequencies more efficiently.
Select 80Hz or 125Hz (8 depending upon the size of cabinet. Larger cabinets ca usually produce lower frequencies, so ) n
80Hz would be a good choice for 15 top cabinets and maybe 125Hz for 8 top cabinets, depending also upon the type of ” ”
program material being played through the system. Experimentation is recommended. an unfiltered, full-range output If
is needed, connect the Left + Right LINK XLR outputs (2) to the full-range active speakers or amplifier. so, use these Al
outputs to feed to further active sub-woofers if necessary.
If there are Left + Right CASA active subwoofers in the sound system, use either Left or Right inputs and link ju st th is
one side to full-range or top cabinets (either LINK or OUTPUT).
When all signal connections are made, connect the power lead provided (or equivalent) from the mains power supply to
the IEC inlet on the CASA s ubwoofer (9). Ensure that the mains voltage is as indicated on the rear panel of the CASA
active subwoofer.
Operation
With the MASTER output level control turned fully down (7), switch on power to the CASA subwoofer (4)
Ensure that a signal is playing to the input(s) and gradually increase the MASTER to the required level. The ON LED (6)
stays lit to show that the unit is powered up but the SIGNAL LIMIT LED (6) should only light briefly on the loudes t parts
of audio (usually beats of a kick drum or other loud transients). If this LED lights for longer periods, it is advised to
reduce the output level to avoid overload.
Where 2 or more subwoofers are used un the same space, if they are facing each other, the signals ca n cancel each
other out, in this case, one of the subwoofers would need to be phase-reversed by switching the PHASE butto (5) to “ ” n
the oppo setting to the other subwoofer. This phase switch can also be used to help to mitigate feedback or lostsite “ ” sub
output in a room through experimenting with either setting.
Turn dow n the MASTER level before powering down the CASA active subwoofer to avoid loud noises and disconnect from
the mai supply if not being used for long periods. ns
1.
L+R LINE inputs combo Jack/XLR
2.
L+R full range LINE LINK outputs combo Jack/XLR
3.
L+R filtered LINE TPUTs combo Jack/XLR OU
4.
Power on/off switch
5.
Phase switch 0°/ 180°
6.
SIGNAL LIMIT & ON LEDs
7.
MASTER o put level control ut
8.
Filtered LINE out cutoff frequency switch 80/125Hz
9.
IEC mains inlet & fuse holder

Specyfikacje produktu

Marka: Citronic
Kategoria: subwoofer
Model: CASA-10BA

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Citronic CASA-10BA, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje subwoofer Citronic

Citronic

Citronic CASA-10BA Instrukcja

20 Września 2024
Citronic

Citronic CASA-18BA Instrukcja

20 Września 2024
Citronic

Citronic C-SUB-12 Instrukcja

18 Września 2024
Citronic

Citronic CASA-15BA Instrukcja

17 Września 2024
Citronic

Citronic CASA-12BA Instrukcja

17 Września 2024

Instrukcje subwoofer

Najnowsze instrukcje dla subwoofer

JL Audio

JL Audio SGR-10TW3 Instrukcja

13 Października 2024
Teufel

Teufel T6 Instrukcja

13 Października 2024
Polk

Polk DB1040 Instrukcja

10 Października 2024
OSD Audio

OSD Audio NERO DUAL X8 Instrukcja

9 Października 2024
OSD Audio

OSD Audio NERO WSA Instrukcja

9 Października 2024
Kicker

Kicker 51CWQ102 Instrukcja

9 Października 2024
Kicker

Kicker 51CWQ122 Instrukcja

9 Października 2024
Kicker

Kicker 43C84 Instrukcja

9 Października 2024
Kicker

Kicker 51CWQ124 Instrukcja

9 Października 2024
OSD Audio

OSD Audio FS12 Instrukcja

9 Października 2024