Instrukcja obsługi Cisco Aironet 2600e

Cisco Punkt dostępu Aironet 2600e

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Cisco Aironet 2600e (40 stron) w kategorii Punkt dostępu. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/40
G ETTING S GTARTED UIDE
Cisco Aironet 2600 Series Access Points
July, 2012
P/N: 78-20842-01
1About this Guide
2Introduction to the Access Point
3Safety Instructions
4Unpacking
5Configurations
6Access Point Ports and Connectors
7Configuring the Access Point
8Mounting the Access Point
9Deploying the Access Point on the Wireless Network
10 Troubleshooting
11 Declarations of Conformity and Regulatory Information
12 Configuring DHCP Option 43 and DHCP Option 60
13 Access Point Specifications
2
1 About this Guide
This Guide provides instructions on how to install and configure your Cisco Aironet 2600 Series
Access Point. The 2600 Series Access Point is referred to as the 2600 series or the access point
in this
document.
2 Introduction to the Access Point
The 2600 series supports high-performing Spectrum Intelligence which sustains three spatial stream
rates over a deployable distance with high reliability when serving clients. The 2600 series provides
high reliability and overall wireless performance.
The 2600 series offers dual-band radios (2.4 GHz and 5 GHz) with integrated and external antenna
options. The access points support full inter-operability with leading 802.11n clients, and support a
mixed deployment with other access points and controllers.
The 2600 series access point is available in both controller-based (Unified) and standalone
(Autonomous) configurations and supports:
Simultaneous single-band or dual-band (2.4 GHz/5 GHz) radios
Integrated antennas on 2602I access point models (AIR-CAP2602I-x-K9)
External antennas for rugged 2602E access point models (AIR-CAP2602E-x-K9)
Note The x in the model numbers represents the regulatory domain. Refer to Regulatory
Domains section on page 6 for a list of supported regulatory domains.
The features of the 2600 series are:
Processing sub-systems (including CPUs and memory) and radio hardware which supports:
Network management
CleanAirAutomatic detection, classification, location and mitigation of RF interference
(not available on autonomous or standalone models)
ClientLink 2.0—BeamForming to 802.11n clients as well as legacy 802.11a/g OFDM clients
VideoStream
Location
WIDS/WIPS
Security
Radio Resource Management (RRM)
Rogue detection
3
Management Frame Protection (MFP)
Throughput, forwarding, and filtering performance scaled to meet 3 spatial stream, 450 Mbps
data-rates
32 MB flash size
802.11af/at
CDP (Cisco Discovery Protocol)
2.4 GHz and 5 GHz 802.11n radios with the following features:
3TX x 4RX
3-spatial streams, 450 Mbps PHY rate
Spectrum intelligence
DPD (Digital Pre-Distortion) technology
Cisco Vector BeamformingImplicit Co-phase beamforming for .11ag clients and 1
spatial-stream and 2 spatial-stream clients
Radio hardware is capable of explicit compressed beamforming (ECBF) per 802.11n standard
3 Safety Instructions
Translated versions of the following safety warnings are provided in the translated safety warnings
document that is shipped with your access point. The translated warnings are also in the Translated
Safety Warnings for Cisco Aironet Access Points, which is available on Cisco.com.
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury.
Before you work on any equipment, be aware of the hazards involved with electrical
circuitry and be familiar with standard practices for preventing accidents. Use the
statement number provided at the end of each warning to locate its translation in the
translated safety warnings that accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS
Warning
Read the installation instructions before you connect the system to its power source.
Statement 1004


Specyfikacje produktu

Marka: Cisco
Kategoria: Punkt dostępu
Model: Aironet 2600e

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Cisco Aironet 2600e, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Punkt dostępu Cisco

Cisco

Cisco MR12 Instrukcja

14 Października 2024
Cisco

Cisco AIR-CAP702I-I-K9 Instrukcja

4 Października 2024
Cisco

Cisco Meraki MR74 Instrukcja

3 Października 2024
Cisco

Cisco Aironet 1142N Instrukcja

27 Września 2024
Cisco

Cisco Meraki MR72 Instrukcja

19 Września 2024
Cisco

Cisco Meraki MR42 Instrukcja

13 Września 2024
Cisco

Cisco Aironet 1810 Instrukcja

10 Września 2024

Instrukcje Punkt dostępu

Najnowsze instrukcje dla Punkt dostępu