Instrukcja obsługi Cisco 910

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Cisco 910 (36 stron) w kategorii router. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/36
1
Cisco Systems, Inc. www.cisco.com
Cisco 910 Industrial Router Hardware
Installation Guide
First Published: July 8, 2014
Last Updated: May 12, 2015
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE
WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO
BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE
FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE
INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE.
IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO
REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case users will be required to correct the interference at
their own expense.
The following information is for FCC compliance of Class B devices: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and us structions, may cause harmful ed in accordance with the in
interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If the equipment causes interference to radio or television reception, which can be determined by turning the
equipment off and on, users are encouraged to try to correct the interference by using one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Modifications to this product not authorized by Cisco could void the FCC approval and negate your authority to operate
the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of
California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved.
Copyright © 1981, Regents of the University of California.
2
Cisco 910 Industrial Router Hardware Installation Guide
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS
ARE PROVIDED AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES,
EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE
PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR
INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING
OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES.
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses
and phone numbers. Any examples, command display output, network topology diagrams, and other figures included in
the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in illustrative
content is unintentional and coincidental.
All printed copies and duplicate soft copies are considered un-Controlled copies and the original on-line version should
be referred to for latest version.
Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco website
at www.cisco.com/go/offices.
5
Preface
Audience
Preface
Audience
This guide is for networking or computer technicians responsible for installing the Cisco 910 Industrial Routers. We
assume that you are familiar with the concepts and terminology of Ethernet and local area networking.
Purpose
This guide documents the hardware features of the Cisco 910 Industrial Routers. It describes the physical and
performance characteristics of the router, explains how to install a router, and provides troubleshooting information.
For configuration information, see the Cisco 910 Industrial Routers documentation on Cisco.com. For system
requirements, important notes, limitations, open and resolved bugs, and documentation updates, see the Cisco 910
Industrial Router release notes on Cisco.com.
Conventions
This document uses the following conventions and symbols for notes, cautions, and warnings.
Note: Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual.
Caution: Means reader be careful. In this situation, you might do something that could result in equipment damage
or loss of data.
Warning: This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work
on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices
for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in
the translated safety warnings that accompanied this device. Statement 1071
Related Publications
Before installing, configuring, or upgrading the router, see the release notes on Cisco.com for the latest information.
These documents provide complete information about the router and are available on Cisco.com:
Cisco 910 Industrial Router Quick Start Guide
Mounting Kit Assembly Guide for the Cisco 910 Industrial Router
Release Notes for the Cisco 910 Industrial Router
Cisco 910 Industrial Router Software Configuration Guide
Obtaining Documentation and Submitting a Service Request
For information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a service request, and
gathering additional information, see What’s New in Cisco Product Documentation at:
http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.html.
Subscribe to What’s New in Cisco Product Documentation, which lists all new and revised Cisco technical
documentation as an RSS feed and delivers content directly to your desktop using a reader application. The RSS feeds
are a free service.

Specyfikacje produktu

Marka: Cisco
Kategoria: router
Model: 910

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Cisco 910, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje router Cisco

Cisco

Cisco EPC3212 Instrukcja

6 Października 2024
Cisco

Cisco DPC2320 Instrukcja

1 Października 2024
Cisco

Cisco 4351 Instrukcja

27 Września 2024
Cisco

Cisco 910 Instrukcja

27 Września 2024
Cisco

Cisco WES610N Instrukcja

5 Września 2024
Cisco

Cisco 7204VXR Instrukcja

5 Września 2024
Cisco

Cisco WRVS4400n Instrukcja

21 Sierpnia 2024
Cisco

Cisco E900 Instrukcja

18 Sierpnia 2024
Cisco

Cisco UC540 Instrukcja

15 Sierpnia 2024

Instrukcje router

Najnowsze instrukcje dla router

Netgear

Netgear LB2120 4G LTE Instrukcja

15 Października 2024
Linksys

Linksys WRT3200ACM Instrukcja

15 Października 2024
D-Link

D-Link DAP-1360 Instrukcja

15 Października 2024
TP-Link

TP-Link Archer AXE75 Instrukcja

14 Października 2024
Linksys

Linksys EA8500 Instrukcja

13 Października 2024
Totolink

Totolink ND300 Instrukcja

12 Października 2024
ZyXEL

ZyXEL LTE 7460 Instrukcja

10 Października 2024
Netgear

Netgear Nighthawk R7200 Instrukcja

10 Października 2024
Netgear

Netgear FR114P Instrukcja

10 Października 2024
Asus

Asus RT-BE86U Instrukcja

9 Października 2024