Instrukcja obsługi Chief SSB2220
Chief
Akcesoria do projektora
SSB2220
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief SSB2220 (1 stron) w kategorii Akcesoria do projektora. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8850-000148 RevB
©2009 Milestone AV Technologies,
a Duchossois Group Company
05/09
SSB-2220, SSM-2220, SLB-2220 and SLM-2220 Interface Brackets
SSB-2220, SSM-2220, SLB-2220 and SLM-2220 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information. Unpack carton and verify kit contents. If any listed parts are
missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
**Only used when installing SLB/SSB interface brackets. ****Used when mounting surface of projector is recessed.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the encircled
locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket
installation.
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down.
3. Place interface bracket onto bottom of projector with three threaded inserts face up and two towards front of projector. Secure interface bracket to
projector using selected screw for model of projector (countersink screw or pan head screw).
4. Countersink screw in center countersink hole and pan head mounting screw in flush mounting hole. Your projector may require one or three
spacers for aligning bracket flat to projector. (Some models may suspend over bottom and have space between bracket and projector.)
Hitachi CP-X270W
1. Place projector upside down on table with projector lens facing away. Stack 1/2" x .190 x 1/2" and 1/2" x .190 x 3/8" on top of each other and
centered over right threaded insert in front of projector. Using two 1/2" x .218 x 1/4" ,1/2" x .218 x 1/4" and 1/2" x .258 x 3/16" spacers, stack and
place them over three threaded inserts on left.
2. Place interface bracket onto projector and align spacers and mounting holes.
3. Position and align interface bracket to projector using M4 x 30mm countersink screw in middle of bracket, M4 x 30mm Phillips pan head screw in
right of bracket, and M4 x 16mm Phillips pan head screw in left of bracket. Tighten all fasteners at this time, securing the bracket to the projector.
Hitachi CP-S307W, CP-X380W, CP-X385W
1. Place projector upside down on table with projector lens facing away. Stack 1/2" x .218 x 1/4" and 1/2" x .258 x 3/16" spacers on top of each other
centered over right threaded insert in front of projector. Using two 1/2" x .258 x 3/16" spacers, place one over middle threaded insert and one over
left threaded insert of projector.
2. Place interface bracket onto projector and align spacers and mounting holes.
3. Position and align interface bracket to projector using M4 x 16mm countersink screw in middle of bracket, M4 x 20mm Phillips pan head screw in
right hole of bracket and M4 x 16mm Phillips pan head screw in left hole of bracket. Tighten all fasteners at this time, securing the bracket to the
projector.
NOTE: Security Screws can be substituted when mounting interface bracket to projector by using the parts and installation instructions in
the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (3) 1/2" x .218" x 1/4" Round Spacer **** (1) Screw, Phillips Flat Head,
Machine, M4 x 16mm **** (1) Screw, Phillips Pan Head,
Machine, M4 x 30mm ****
(4) 10 - 24 Thumb
Nuts** (3) 1/2" x .194" x 1/2" Round Spacer **** (1) Screw, Phillips Pan Head,
Machine, M4 x 16mm **** (3) 1/2" x .257" x 3/16" Round
Spacer ****
(1) All-Points Security
Kit (3) 1/2" x .194" x 3/8" Nylon Spacer **** (1) Screw, Phillips Flat Head Machine,
M4 x 25mm **** (3) 1/2" x .257" x 3/16" Round
Spacer ****
(2) Washer, Flat, M4 (1) Screw, Phillips Pan Head, Machine,
M4 x 8mm **** (1) Screw, Phillips Pan Head,
Machine, M4 x 20mm **** (3) 1/2" x .257" x 3/16" Round
Spacer ****
SLB-2220 SLM-2220
Towards front of
projector
Towards front of
projector
(
N
ote: SSB-style interface bracket connections
a
r
e
e
n
c
ir
c
l
e
d
)
(Note: SSM-style interface bracket connection
s
a
re encircled)
Specyfikacje produktu
| Marka: | Chief |
| Kategoria: | Akcesoria do projektora |
| Model: | SSB2220 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Chief SSB2220, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Akcesoria do projektora Chief
31 Grudnia 2025
31 Grudnia 2025
31 Grudnia 2025
31 Grudnia 2025
31 Grudnia 2025
31 Grudnia 2025
31 Grudnia 2025
31 Grudnia 2025
31 Grudnia 2025
31 Grudnia 2025
Instrukcje Akcesoria do projektora
- Akcesoria do projektora Sony
- Akcesoria do projektora Panasonic
- Akcesoria do projektora Viewsonic
- Akcesoria do projektora Nedis
- Akcesoria do projektora Casio
- Akcesoria do projektora Manhattan
- Akcesoria do projektora Sanus
- Akcesoria do projektora My Wall
- Akcesoria do projektora Lindy
- Akcesoria do projektora Konig & Meyer
- Akcesoria do projektora V7
- Akcesoria do projektora Auna
- Akcesoria do projektora Chipolino
- Akcesoria do projektora Peerless-AV
- Akcesoria do projektora XGIMI
- Akcesoria do projektora NEC
- Akcesoria do projektora Sanyo
- Akcesoria do projektora Vision
- Akcesoria do projektora Optoma
- Akcesoria do projektora Vogel's
- Akcesoria do projektora Omnitronic
- Akcesoria do projektora Barco
- Akcesoria do projektora Gabor
- Akcesoria do projektora BenQ
- Akcesoria do projektora Kanto
- Akcesoria do projektora Newstar
- Akcesoria do projektora Speaka
- Akcesoria do projektora Da-Lite
- Akcesoria do projektora AV:link
- Akcesoria do projektora InFocus
- Akcesoria do projektora Projecta
- Akcesoria do projektora Peerless
- Akcesoria do projektora Tempest
- Akcesoria do projektora Roadinger
- Akcesoria do projektora Premier Mounts
- Akcesoria do projektora Elite Screens
- Akcesoria do projektora Kingpin Screens
- Akcesoria do projektora Unicol
- Akcesoria do projektora Smart Media
- Akcesoria do projektora NeoMounts
- Akcesoria do projektora SMK-Link
Najnowsze instrukcje dla Akcesoria do projektora
14 Stycznia 2025
10 Stycznia 2025
7 Stycznia 2025
26 Grudnia 2024
26 Grudnia 2024
22 Grudnia 2024
19 Grudnia 2024
19 Grudnia 2024
18 Grudnia 2024
18 Grudnia 2024