Instrukcja obsługi Chief SSB122

Chief Akcesoria do projektora SSB122

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief SSB122 (1 stron) w kategorii Akcesoria do projektora. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8850-000113 Rev B
©2009 Milestone AV Technologies,
a Duchossois Group Company
05/09
SSB-122, SSM-122, SLB-122 and SLM-122 Interface Brackets
SSB-122, SSM-122, SLB-122 and SLM-122 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place 1/2" spacers over the threaded inserts on raised area of projector, and place 5/8" spacers over the threaded inserts on lower area
of projector.
4. Place interface bracket over projector bottom and align the mounting holes in bracket with the threaded inserts in projector.
5. Secure interface bracket to projector using M4 x 20mm Phillips pan head screw and M4 x 20mm Phillips flat head screw with flat washers
(i.e., in shorter spaces of projector). Use M4 x 25mm Phillips pan head screw and M4 x 25mm Phillips flat head screw with flat
washers (i.e., in longer spacers of projector). Tighten all fasteners at this time.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (1) Screw, Phillips Flat Head Machine M4 x 25mm ****
(4) 10-24 Thumb Nuts ** (1) Screw, Phillips Pan Head, Machine, M4 x 20mm ****
(1) All-Points Security Kit (1) Screw, Phillips Flat Head, Machine, M4 x 20mm ****
(2) 1/2" x .257 x 5/8" Nylon Spacer **** (2) Washer, Flat, M4
(2) 1/2" x .194 x 1/2" Round Spacer **** (1) Screw, Phillips Pan Head, Machine, M4 x 25mm ****
**Only used when installing SLB/SSB interface brackets. ****Used when mounting surface of projector is recessed.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style
interface bracket installation.
SLB-122 SLM-122
Towards front of
projector
Towards front of
projector
(Note: SSM-style interface bracket connection
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(
Note: SSB-style interface bracket connections
r
e
e
c
i
r
c
l
e
d
)

Specyfikacje produktu

Marka: Chief
Kategoria: Akcesoria do projektora
Model: SSB122

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Chief SSB122, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Akcesoria do projektora Chief

Chief

Chief RPMC198 Instrukcja

31 Grudnia 2025
Chief

Chief RPMA360 Instrukcja

31 Grudnia 2025
Chief

Chief RSMA342 Instrukcja

31 Grudnia 2025
Chief

Chief RSMA360 Instrukcja

31 Grudnia 2025
Chief

Chief RPMC266 Instrukcja

31 Grudnia 2025
Chief

Chief RSMC360 Instrukcja

31 Grudnia 2025
Chief

Chief RPMA303 Instrukcja

31 Grudnia 2025
Chief

Chief RPMC246 Instrukcja

31 Grudnia 2025
Chief

Chief RSA000S Instrukcja

31 Grudnia 2025
Chief

Chief RSA360 Instrukcja

31 Grudnia 2025

Instrukcje Akcesoria do projektora

Najnowsze instrukcje dla Akcesoria do projektora

Barco

Barco R9853370 Instrukcja

14 Stycznia 2025
Vogel's

Vogel's PPA 904 Instrukcja

10 Stycznia 2025
Roadinger

Roadinger MBT-3 Instrukcja

7 Stycznia 2025
Peerless-AV

Peerless-AV PE1120-W Instrukcja

26 Grudnia 2024
Peerless-AV

Peerless-AV PAP-SANYO-ST1 Instrukcja

26 Grudnia 2024
Sony

Sony VPLL-Z4111 Instrukcja

22 Grudnia 2024
NeoMounts

NeoMounts BEAMER-C300 Instrukcja

19 Grudnia 2024
NeoMounts

NeoMounts BEAMER-C80 Instrukcja

19 Grudnia 2024
NeoMounts

NeoMounts BEAMER-W050SILVER Instrukcja

18 Grudnia 2024
NeoMounts

NeoMounts CL25-540BL1 Instrukcja

18 Grudnia 2024