Instrukcja obsługi Chief SLM279

Chief Akcesoria do projektora SLM279

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief SLM279 (1 stron) w kategorii Akcesoria do projektora. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/1

I N S T A L L A T I O N I N S T R U C T I O N S

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes

no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use

of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or

implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief Manufacturing, a products division of Milestone AV Technologies

8401 Eagle Creek Parkway, Savage, MN 55378

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8802-002081 Rev00

a Duchossois Group Company

01/11

SSB-279, SSM-279, SLB-279 and SLM-279 Interface Brackets

SSB-279, SSM-279, SLB-279 and SLM-279 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific

installation instructions provided with the mount for additional installation information.

Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

Installation Instructions

WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface brackets.

NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.

1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.

2. Turn projector upside down on a flat surface.

3. Place four spacers over the threaded inserts in the bottom of the projector. NOTE: The short spacer should be placed as noted in drawing.

4. Place the interface bracket onto the bottom of the projector, aligning the mounting holes in the bracket with the threaded inserts in the

bottom of the projector and ensuring that triangle in bracket points towards front of projector.

5. Position mounting screws through M4 washers, interface bracket, nylon spacers, and into the threaded inserts in bottom of projector.

NOTE: Place M4 x 20mm Phillips screw into the bracket as noted in drawing. Tighten all fasteners at this time, securing the bracket to the

projector.

NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the

All-Points Security Kit.

(1) Interface Bracket (3) Screw, Phillips Pan Head, Machine, M4 x 35mm

(4) 10-24 Thumb Nuts ** (1) Screw, Phillips Pan Head, Machine, M4 x 20mm

(1) All-Points Security Kit (4) Washer, M4

(1) 5/32" Security Hex Key (1) Spacer, Nylon, 1/2" x .194" x 3/8"

(3) Spacer, Nylon, .50" x .257 x 1.00

**Only used when installing SLB/SSB interface brackets.

NOTE: Specific to SSB-style and SSM-style interface bracket installation: All appropriate screws come pre-installed in the circled locations above.

DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket installation.

Note: SSB-style interface bracket connections are circled. Note: SSM-style interface bracket connections are circled.

SLB-279 SLM-279

Towards front

of projector

Towards front

of projector

M4 x 20 Phillips screw

1/2" x .194" x 3/8" spacer

Specyfikacje produktu

Marka:	Chief
Kategoria:	Akcesoria do projektora
Model:	SLM279

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Chief SLM279, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Akcesoria do projektora Chief

Chief RPMC198 Instrukcja

31 Grudnia 2025

Chief RPMA360 Instrukcja

31 Grudnia 2025

Chief RSMA342 Instrukcja

31 Grudnia 2025

Chief RSMA360 Instrukcja

31 Grudnia 2025

Chief RPMC266 Instrukcja

31 Grudnia 2025

Chief RSMC360 Instrukcja

31 Grudnia 2025

Chief RPMA303 Instrukcja

31 Grudnia 2025

Chief RPMC246 Instrukcja

31 Grudnia 2025

Chief RSA000S Instrukcja

31 Grudnia 2025

Chief RSA360 Instrukcja

31 Grudnia 2025

Instrukcje Akcesoria do projektora

Najnowsze instrukcje dla Akcesoria do projektora

Barco R9853370 Instrukcja

14 Stycznia 2025

Vogel's PPA 904 Instrukcja

10 Stycznia 2025

Roadinger MBT-3 Instrukcja

7 Stycznia 2025

Peerless-AV PE1120-W Instrukcja

26 Grudnia 2024

Peerless-AV PAP-SANYO-ST1 Instrukcja

26 Grudnia 2024

Sony VPLL-Z4111 Instrukcja

22 Grudnia 2024

NeoMounts BEAMER-C300 Instrukcja

19 Grudnia 2024

NeoMounts BEAMER-C80 Instrukcja

19 Grudnia 2024

NeoMounts BEAMER-W050SILVER Instrukcja

18 Grudnia 2024

NeoMounts CL25-540BL1 Instrukcja

18 Grudnia 2024