Instrukcja obsługi Chief SLB087


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chief SLB087 (1 stron) w kategorii uchwyt do płaskiego ekranu. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the infor-
mation contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The
information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the
information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
© 2006 Chief Manufacturing, 8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8850-00076
7/19/06
SLB-087 and SLM-087 Interface Brackets
SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by calling
1-800-582-6480.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation:
WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB Interface bracket. If an SLM bracket is being installed proceed to step 2.
1. Screw six thumb screws onto six 10-24 x 5/8" Philips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place three, 1/2" spacers over three threaded inserts in bottom of projector.
4. Place Interface bracket onto bottom of projector, aligning mounting mounting holes and spacers.
5. Secure Interface bracket to projector using three M4 x 20mm Philips flat head screws and flat washers.
NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the
All-Points Security Kit.
(1) Interface Bracket (3) Screw, Philips Flat Head, Machine, M4 x 20mm ****
(6) 10-24 Thumb Nuts ** (3) 1/2" x .194 x 1/2" Nylon Spacer ****
(1) All-Points Security Kit
**Only used when installing SLB Interface brackets.
****Used when mounting surface of projector is recessed.


Specyfikacje produktu

Marka: Chief
Kategoria: uchwyt do płaskiego ekranu
Model: SLB087

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Chief SLB087, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje uchwyt do płaskiego ekranu Chief

Chief

Chief SLB087 Instrukcja

18 Września 2024

Inne instrukcje Chief

Chief

Chief TS325TU Instrukcja

8 Października 2024
Chief

Chief AS3A100 Instrukcja

7 Października 2024
Chief

Chief Fit Mobile Cart Instrukcja

7 Października 2024
Chief

Chief AS3A102 Instrukcja

7 Października 2024
Chief

Chief FCAV1U Instrukcja

7 Października 2024
Chief

Chief XBM1UP Instrukcja

7 Października 2024
Chief

Chief MPD1U Instrukcja

7 Października 2024
Chief

Chief PFQUB Instrukcja

6 Października 2024
Chief

Chief Fusion Instrukcja

5 Października 2024
Chief

Chief PFMUB Instrukcja

5 Października 2024