Instrukcja obsługi Chamberlain CWPIR

Chamberlain detektor ruchu CWPIR

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chamberlain CWPIR (2 stron) w kategorii detektor ruchu. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
1
Carton Inventory
Assembly & Programming
Attach PIR Motion Sensor box
to mounting plate with large
silver screw. Tighten screw
until PIR Motion Sensor stays
in place when repositioned.
Passive Infra-Red (PIR)
Motion Sensor
Swivel Bushing
Mounting PlateSun/Rain Shield
1
Install 4 AA Alkaline
batteries. (Lithium batteries
recommended for colder
environments.)
LED light will fl ash.
2
Antenna
ON
OFF
1 2
SWITCH SETTINGS
Switch #1 Switch #2
Learn
Button
OFF Low Sensitivity
ON High Sensitivity (Default)
OFF 15 Feet (4.5 m) Detection Range
ON 30 Feet (9.1 m) Detection Range
(Default)
NOTE: To avoid unwanted detection of small animals move
Switch #2 to OFF.
PIR Motion Sensor
SWITCH #1:
SWITCH #2:
A Ensure Base Station and PIR
Motion Sensor are in close
proximity to each other.
Press and release Learn
Button on Base Station.
Buzzer will sound.
B Within 60 seconds, press the
Learn Button on the inside of
the PIR Motion Sensor. LED
light will illuminate and Base
Station will buzz.
3Learn Button
Test PIR Motion Sensor by
waving hand in front of sensor.
LED light should fl ash and
the Base Station will buzz X
number of times indicating
which sensor has been
activated.
Insert battery pack facing away
from circuit board and fasten
cover with the smallest screws
(provided).
NOTE: Ensure the batteries do
not touch the circuit board and
the antenna and battery wires
are not pinched.
4
5
Overview
Learn Button
Models CWPIR and CWPIRC
WIRELESS MOTION ALERT SENSOR
®
The Wireless Alert Sensor is a Passive Infra-Red (PIR) Motion Sensor that detects movement of people and vehicles, while allowing
small animals to pass through undetected. Each sensor has its own unique ID, for a secure radio link. The base station (not provided)
can learn the signals of up to 8 sensors. The base station gives a single beep for the fi rst sensor that is programmed, a double beep for
the second, and so on. Additionally, multiple base stations can work with the same sensor to sound in different places.
Assembly & Programming
PIR MOTION SENSOR INSTALLATION
Mount PIR Motion Sensor
horizontally on solid surface
3-5 feet (1-1.5 m) off the
ground and within 1/2 mile
(0.8 km) of Base Station (rotate
sensor to access screw holes).
Unit should be able to swivel as
needed.
Attach sun/rain shield.
NOTE: Keep PIR Motion
Sensor antenna away from
metal objects. Do not mount
PIR Motion Sensor in direct
sunlight, near moving tree
branches, or in the path of a
sprinkler system.
4 feet (1.2 m)
10-20 feet (3-6 m)
Vehicle Alert Installation: For cars, the best mounting position
is about 4 feet (1.2 m) high, between 10-20 feet (3-6 m)back,
and angled to see the back of car after passing the sensor.
6
Troubleshooting
The PIR Motion Sensor lights up, but the Base Station does
not respond.
The PIR Motion Sensor must be programmed to Base Station
(See Step 3). Ensure Base Station is on and the volume is
turned up.
PIR Motion Sensor is detecting motion only part of the time.
Ensure the PIR Motion Sensor is set to the High Sensitivity
setting (See Step 2). To detect cars, it is best to mount PIR
Motion Sensor at height of car’s motor and have it between
10-20 feet (3-6 m) from the road. Swivel sensor as needed.
The Alert is giving false alarms.
Check for moving tree branches or insects in sensor window.
PIR Motion Sensor can also be triggered by light shining
directly in sensor window, such as refl ected sunlight, or motion
in front of a light source.
It is possible that condensation has built up on the sensor. Wipe
condensation from PIR Motion Sensor with cotton swab. Let it
sit inside for a few hours, open to the air, without the batteries
and it should correct itself.
Check Sensor Switches on PIR Motion Sensor. See Switch
Settings.
Base Station beeps every 30 minutes.
The batteries in the Base Station or the PIR Motion Sensor(s)
are low. Replace the 4 AA batteries. Check the PIR Motion
Sensor(s), if the LED illuminates on all of the PIR Motion
Sensors, change the batteries in the Base Station.
The Alert is not getting expected transmission range.
Keep both antennas vertical and keep PIR Motion Sensor
antenna away from trees and metal objects. Ensure Base Station
is in clearest possible sight of the PIR Motion Sensor. The less
objects between the devices, the longer the range.
NOTE: The manufacturer is not responsible for any radio or
TV interference caused by unauthorized modifi cations to this
equipment. Changes or modifi cations not expressly approved
by the manufacturer could void the user’s authority to operate
the equipment.
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:
1-800-528-9131
www.chamberlain-DIY.com
© 2010, The Chamberlain Group Inc.
114A3897D All Rights Reserved

Specyfikacje produktu

Marka: Chamberlain
Kategoria: detektor ruchu
Model: CWPIR

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Chamberlain CWPIR, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje detektor ruchu Chamberlain

Chamberlain

Chamberlain CWA2000C Instrukcja

30 Sierpnia 2024
Chamberlain

Chamberlain CWPIRC Instrukcja

28 Sierpnia 2024
Chamberlain

Chamberlain CWPIR Instrukcja

23 Sierpnia 2024

Instrukcje detektor ruchu

Najnowsze instrukcje dla detektor ruchu

Crestron

Crestron GLA-LDL-PC-0-10 Instrukcja

9 Stycznia 2025
D-Link

D-Link DCH-S150 Instrukcja

29 Grudnia 2024
EQ-3

EQ-3 HM-Sen-MDIR-O-2 Instrukcja

29 Grudnia 2024
Megatron

Megatron MT68032 Instrukcja

26 Grudnia 2024
Megatron

Megatron MT68030 Instrukcja

26 Grudnia 2024
Lucide

Lucide Eclips Instrukcja

25 Grudnia 2024
Optex

Optex SIP-100 Instrukcja

17 Grudnia 2024
Optex

Optex SL-350QDM Instrukcja

17 Grudnia 2024
Optex

Optex SIP-3020WF Instrukcja

17 Grudnia 2024
Optex

Optex FLX-S Instrukcja

17 Grudnia 2024