Instrukcja obsługi Celestron ThermoCharge 10

Celestron bank mocy ThermoCharge 10

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Celestron ThermoCharge 10 (8 stron) w kategorii bank mocy. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

#21135

Unpack your telescope and verify that all parts are present. Your

Travel Scope 70 includes: a telescope tube, a tripod and mount

head, two eyepieces, a 3x Barlow lens, a finderscope, an erect image

diagonal, a smartphone adapter, a Bluetooth shutter remote, and a

Moon filter.

To extend the tripod’s central column, turn the locking knob

counterclockwise, lift up the tripod head until it is at the desired

height and turn the locking knob clockwise to secure.

Rotate the mounting platform so it is horizontal and tighten the knob

to secure it.

To set up the tripod, spread the legs outward until they are fully

extended and push down on the center leg brace.

Loosen the knob on the side of the tripod head mounting platform

and rotate the platform 90 degrees so it is standing vertically.

Remove the cap from the focuser end of the telescope tube and

make sure the two thumbscrews do not protrude into the opening.

Extend the legs of the tripod by unlocking the three tripod lock levers

on each leg. Pull each leg section all the way out and push the lever

on each lock downward to secure it in place.

Match the threaded bolt in the mounting platform to the threaded

hole on the bottom of the telescope tube and thread the two together.

Do not overtighten. This should be snug, but not tight.

Locate the erect image diagonal and remove the plastic covers. Insert

the barrel of the diagonal into the focuser and secure in place by

tightening the set screws.

#21135

Insert the barrel of the 20mm eyepiece into the diagonal and tighten

the set screw.

Remove the lens cap from the front of the telescope. To observe,

look through the eyepiece as shown. Focus the image by turning the

knobs below the focuser.

To move the scope right and left, hold a tripod leg with one hand

while the other hand uses the panning handle to move the scope.

The azimuth locking screw can be loosened or tightened to adjust the

tension to your preference.

Remove the knurled nuts on the threaded posts at the focuser end

of the telescope tube.

For additional magnification, you can use the included 3x Barlow

lens. Place the Barlow lens between the diagonal and the eyepiece.

To move the scope up and down, rotate the entire pan handle

counterclockwise and use the handle to point the scope in the

direction you want to view. Rotate the pan handle clockwise to

lock it in place.

Locate the finderscope and remove the plastic caps on the front and

back lens. Orient the finderscope so that the larger lens is facing

towards the front of the tube as shown. Place the finderscope over the

posts on the tube and replace the knurled nuts to secure it in place.

To use the Moon filter, remove the eyepiece from the diagonal or

Barlow lens. Thread the filter onto the bottom of the eyepiece and

re-insert the eyepiece into the diagonal or Barlow.

For more information on this product or to download

the instruction manual, please visit the respective

product page on celestron.com

SOLAR WARNING: Never attempt to view the sun

through any telescope without a proper solar filter.

NEED ASSISTANCE?

Contact Celestron Technical Support

celestron.com/pages/technical-support

07-21

Specyfikacje produktu

Marka:	Celestron
Kategoria:	bank mocy
Model:	ThermoCharge 10
Kolor produktu:	Black, Blue, Orange
Materiał obudowy:	Aluminium
Wbudowany wyłącznik:	Tak
Wysokość produktu:	102.3 mm
Szerokość produktu:	60.2 mm
Głębokość produktu:	35.5 mm
Waga produktu:	286 g
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Źródło ładowania:	USB
Certyfikaty:	CE
Pojemność baterii:	10000 mAh
Technologia baterii:	Litowo-jonowa (Li-Ion)
Napięcie operacyjne:	5 V
Szybkie ładowanie:	Nie
Napięcie:	5 V
Diody LED:	Tak
Prąd wejściowy:	1.8 A
Stopień ochrony IP:	IP65
Wodoodporny:	Tak
Maksymalna liczba jednocześnie podłączonych urządzeń:	2
Kształt:	Prostokąt
Kompatybilność ładowarki:	Uniwersalne
Porty wyjścia USB A:	2
interfejs wejścia:	Mini-USB
Port 1 - napięcie wyjściowe:	1 A
Port 2 - napięcie wyjściowe:	2.1 A
Mini-złącze USB:	Tak
Ilość złącz mini-USB:	1