Instrukcja obsługi Casio G-Shock GW-9400-3ER

Casio zegarek G-Shock GW-9400-3ER

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Casio G-Shock GW-9400-3ER (14 stron) w kategorii zegarek. Ta instrukcja była pomocna dla 34 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/14

E-1

ENGLISH

Congratulations upon your selection of this CASIO watch.

Applications

The built-in sensors of this watch measure direction, barometric pressure, temperature and altitude.

Measured values are then shown on the display. Such features make this watch useful when hiking,

mountain climbing, or when engaging in other such outdoor activities.

Warning !

• The measurement functions built into this watch are not intended for taking measurements that

require professional or industrial precision. Values produced by this watch should be considered

as reasonable representations only.

•

When engaging in mountain climbing or other activities in which losing your way can create a

dangerous or life-threatening situation, always use a second compass to conﬁ rm direction readings.

• Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss

suffered by you or any third party arising through the use of this product or its malfunction.

E-2

Important!

• Your watch’s Altimeter Mode calculates relative altitude based on changes in barometric pressure

measurement by its pressure sensor. For more information, see page E-36 and E-48.

• Immediately before embarking or otherwise taking altitude readings, be sure to specify a reference

altitude. If you don’t the readings produced by the watch probably will not be very accurate. For more

information, see “To specify a reference altitude value” (page E-44).

E-3

About This Manual

• Depending on the model of your watch, digital display text appears

either as dark ﬁ gures on a light background, or light ﬁ gures on a dark

background. All examples in this manual are shown using dark ﬁ gures

on a light background.

• Button operations are indicated using the letters shown in the

illustration.

• Note that the product illustrations in this manual are intended for

reference only, and so the actual product may appear somewhat

different than depicted by an illustration.

E-4

Things to check before using the watch

1. Check the battery power level.

Is H or M indicated by the battery power indicator (page E-11)?

Go to step 2.

Power is low. Charge the watch by placing it in a location

where it is exposed to light. For details, see “Charging the

Watch” (page E-10).

NO YES

YES

Does any one of the following conditions exist?

• Battery power indicator indicates is flashing on the L and LOW

display.

• CHG is flashing on the display.

• The face is blank.

The watch is charged

sufficiently.

For details about

charging, see

“Charging the Watch”

(page E-10).

Battery power

indicator

E-5

2. Check the Home City and the daylight saving time (DST) setting.

Use the procedure under “To conﬁ gure Home City and summer time settings” (page E-31) to conﬁ gure

your Home City and daylight saving time settings.

Important!

• Proper time calibration signal reception, and World Time Mode and Sunrise/Sunset Mode data depend

on correct Home City, time, and date settings in the Timekeeping Mode. Make sure you conﬁ gure

these settings correctly.

3. Set the current time.

• To set the time using a time calibration signal

See “To get ready for a receive operation” (page E-17).

• To set the time manually

See “Conﬁ guring Current Time and Date Settings Manually” (page E-33).

The watch is now ready for use.

• For details about the watch’s radio controlled timekeeping feature, see “Radio Controlled Atomic

Timekeeping” (page E-15).

E-6

Contents

E-3 About This Manual

E-4 Things to check before using the watch

E-10 Charging the Watch

E-14 To recover from the sleep state

E-15 Radio Controlled Atomic Timekeeping

E-17 To get ready for a receive operation

E-19 To perform manual receive

E-22 To check the latest signal reception results

E-22 To turn auto receive on or off

E-24 Mode Reference Guide

E-29 Timekeeping

E-30 Using Date/Time Records

E-31 Conﬁ guring Home City Settings

E-31 To conﬁ gure Home City and summer time settings

E-33 Conﬁ guring Current Time and Date Settings Manually

E-33 To change the current time and date settings manually

E-35 Specifying Temperature, Barometric Pressure, and Altitude Display Units

E-35 To specify temperature, barometric pressure, and altitude display units

E-7

E-36 Using the Altimeter Mode

E-37 To select the altitude screen format

E-37 To select the altitude auto reading interval

E-39 To take altitude readings

E-42 To specify the altitude differential start point

E-43 To use the altitude differential value

E-44 To specify a reference altitude value

E-45 To save a reading manually

E-51 Precautions Concerning Simultaneous Altitude and Temperature Readings

E-52 Taking Direction Readings

E-52 To perform 2-point calibration

E-54 To take a direction reading

E-58 To perform magnetic declination correction

E-61 Taking Barometric Pressure and Temperature Readings

E-61 To take barometric pressure and temperature readings

E-66 To enable or disable the barometric pressure change alert

E-68 To calibrate the pressure sensor and the temperature sensor

E-70 Viewing Memory Records

E-70 To view data in watch memory

E-74 To delete all saved data

E-74 To delete a speciﬁ c record

Operation Guide 3410

E-8

E-75 Checking the Current Time in a Different Time Zone

E-75 To enter the World Time Mode

E-75 To view the time in another time zone

E-76 To specify standard time or daylight saving time (DST) for a city

E-77 Using the Stopwatch

E-77 To enter the Stopwatch Mode

E-77 To perform an elapsed time operation

E-77 To pause at a split time

E-78 To measure two ﬁ nishes

E-79 Using the Countdown Timer

E-79 To enter the Countdown Timer Mode

E-79 To specify the countdown start time

E-80 To perform a countdown timer operation

E-80 To stop the alarm

E-81 Using the Alarm

E-81 To enter the Alarm Mode

E-82 To set an alarm time

E-83 To turn an alarm and the Hourly Time Signal on and off

E-83 To stop the alarm

E-9

E-84 Looking up Sunrise and Sunset Times

E-84 To view sunrise and sunset times

E-85 To view the sunrise/sunset time for a particular date

E-86 To look up the sunrise and sunset times for a speciﬁ c location

E-88 Illumination

E-88 To turn on illumination manually

E-88 To change the illumination duration

E-90 To turn the auto light switch on and off

E-92 Other Settings

E-92 To turn the button operation tone on and off

E-93 To turn Power Saving on or off

E-94 Troubleshooting

E-100 Speciﬁ cations

E-10

Charging the Watch

The face of the watch is a solar panel that generates power from light. The generated power charges a

built-in rechargeable battery, which powers watch operations. The watch charges whenever it is exposed

to light.

Charging Guide

Whenever you are not wearing the

watch, leave it in a location where it

is exposed to light.

• Best charging performance is

achieved by exposing the watch to

the strongest light available.

When wearing the watch, make sure

that its face is not blocked from light

by the sleeve of your clothing.

• The watch may enter a sleep state

(page E-14) if its face is blocked

by your sleeve even only partially.

Warning!

Leaving the watch in bright light for charging can cause it to become quite hot.

Take care when handling the watch to avoid burn injury. The watch can become particularly hot

when exposed to the following conditions for long periods.

• On the dashboard of a car parked in direct sunlight

• Too close to an incandescent lamp

• Under direct sunlight

E-11

Important!

• Allowing the watch to become very hot can cause its liquid crystal display to black out. The

appearance of the LCD should become normal again when the watch returns to a lower temperature.

• Turn on the watch’s Power Saving function (page E-14) and keep it in an area normally exposed to

bright light when storing it for long periods. This helps to ensure that power does not run down.

• Storing the watch for long periods in an area where there is no light or wearing it in such a way that it is

blocked from exposure to light can cause power to run down. Expose the watch to bright light

whenever possible.

Power Levels

You can get an idea of the watch’s power level by observing the battery power indicator on the display.

Important!

• If low battery power is indicated, expose the face of the watch to direct light to charge. At Level 5, the

battery is dead, which causes watch functions to stop, all data in watch memory to be deleted, and all

watch settings to return to their initial factory defaults.

Level Battery Power Indicator Function Status

(H) All functions enabled.

(M) All functions enabled.

Battery power

indicator

Battery power

indicator

E-12

Level Battery Power Indicator Function Status

(L)

Auto and manual receive, illumination,

beeper, and sensor operation disabled.

(CHG)

Except for the CHG (charge) indicator, all

functions and display indicators disabled.

5 – – – All functions disabled.

• The ﬂ ashing LOW

indicator at Level 3 (L) tells you that battery power is very low, and that exposure to

bright light for charging is required as soon as possible.

• Display indicators reappear as soon as the battery is charged from Level 5 to Level 2 (M).

• Leaving the watch exposed to direct sunlight or some other very strong light source can cause the

battery power indicator to show a reading temporarily that is higher than the actual battery level. The

correct battery level should be indicated after a few minutes.

E-13

Power Recovery Mode

• Performing multiple sensor, illumination, or beeper operations during a short period may cause all of

the battery power indicators (H, M, and L) to start ﬂ ashing on the display. This indicates that the watch

is in the power recovery mode. Illumination, alarm, countdown timer alarm, hourly time signal, and

sensor operations will be disabled until battery power recovers.

• Battery power will recover in about 15 minutes. At this time, the battery power indicators (H, M, L) will

stop ﬂ ashing. This indicates that the functions listed above are enabled again.

• If all of the battery power indicators (H, M, L) are ﬂ ashing and the

CHG (charge) indicator also is

ﬂ ashing, it means the battery level is very low. Expose the watch to bright light as soon as possible.

• Even if battery power is at Level 1 (H) or Level 2 (M), the Digital Compass Mode, Barometer/

Thermometer Mode, or Altimeter Mode sensor may be disabled if there is not enough voltage available

to power it sufﬁ ciently. This is indicated when all of the battery power indicators (H, M, L) are ﬂ ashing.

• Frequent ﬂ ashing of all of the battery power indicators (H, M, L) probably means that remaining battery

power is low. Leave the watch in bright light to allow it to charge.

Charging Times

Exposure Level (Brightness)

Daily

Operation

Level Change *2

Level 5 Level 4 Level 3 Level 2 Level 1

Outdoor sunlight (50,000 lux) 5 min. 2 hours 16 hours 5 hours

Sunlight through a window (10,000 lux)

24 min. 7 hours 79 hours 22 hours

Daylight through a window on a

cloudy day (5,000 lux) 48 min. 12 hours 160 hours 43 hours

Indoor ﬂ uorescent lighting (500 lux) 8 hours 175 hours – – – – – –

E-14

*1 Approximate amount of exposure time required each day to generate enough power for normal daily

operation.

*2 Approximate amount of exposure time (in hours) required to take power from one level to the next.

• The above exposure times all are for reference only. Actual exposure times depend on lighting

conditions.

• For details about the operating time and daily operating conditions, see the “Power Supply” section of

the Speciﬁ cations (page E-103).

Power Saving

When turned on, Power Saving enters a sleep state automatically whenever the watch is left for a certain

period in an area where it is dark. The table below shows how watch functions are affected by Power

Saving.

• For information about enabling and disabling power saving, see “To turn Power Saving on or off” (page

E-93).

• There actually are two sleep state levels: “display sleep” and “function sleep”.

Elapsed Time in Dark Display Operation

60 to 70 minutes (display sleep) Blank, with

PS ﬂ ashing Display is off, but all functions are enabled.

6 or 7 days (function sleep) Blank, with

PS not ﬂ ashing All functions are disabled, but timekeeping is

maintained.

• The watch will not enter a sleep state between 6:00 AM and 9:59 PM. If the watch is already in a sleep

state when 6:00 AM arrives, however, it will remain in the sleep state.

• Power Saving is enabled only when the watch is in the Timekeeping Mode with the Day of the Week

screen displayed (page E-29) or in the World Time Mode (page E-75).

To recover from the sleep state

Move the watch to a well-lit area, press any button, or angle the watch towards your face for reading (page E-89).

E-15

Radio Controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly. However, when

using the watch outside of areas covered by time calibration signals, you will have to adjust the settings

manually as required. See “Conﬁ guring Current Time and Date Settings Manually” (page E-33) for more

information.

This section explains how the watch updates its time settings when the city code selected as the Home

City is in Japan, North America, Europe, or China, and is one that supports time calibration signal

reception.

If your Home City Code setting is this: The watch can receive the signal from the transmitter

located here:

LIS, LON, MAD, PAR, ROM, BER, STO, ATH, MOW Anthorn (England), Mainﬂ ingen (Germany)

HKG, BJS Shangqiu City (China)

TPE, SEL, TYO Fukushima (Japan), Fukuoka/Saga (Japan)

HNL, ANC, YVR, LAX, YEA, DEN, MEX, CHI, NYC, YHZ,

YYT Fort Collins, Colorado (United States)

Important!

• The areas covered by MOW,HNL and ANC are quite far from the calibration signal transmitters, so

certain conditions may cause reception problems.

• When HKG or BJS is selected as the Home City, only the time and date are adjusted according to the

time calibration signal. You need to switch manually between standard time and daylight saving time

(DST) if required. See “To conﬁ gure Home City and summer time settings” (page E-31) for information

about how to do this.

Operation Guide 3410

E-16

Approximate Reception Ranges

UK and German Signals

Anthorn

500 kilometers

1,500 kilometers

The Anthorn signal is

receivable within this area Mainflingen

North American Signal

Japanese Signals Chinese Signal

500 kilometers Changchun

Beijing

Shangqiu

Shanghai

Chengdu

Hong Kong

1,500 kilometers

2,000 miles

(3,000 kilometers)

600 miles

(1,000 kilometers)

Fort Collins

1,000 kilometers

Signals are receivable in the Taiwan area

when reception conditions are

ood.

For the Honolulu and Anchorage time zones, the

signal can be received when reception conditions

are favorable.

Fukuoka/Saga

500 kilometers

Fukushima

E-17

• Even when the watch is within range of a transmitter, signal reception may be impossible due to the

effects of geographic contours, structures, weather, the time of year, the time of day, radio interference,

etc. The signal becomes weaker at distances of approximately 500 kilometers, which means that the

inﬂ uence of the conditions listed above becomes even greater.

• Signal reception may not be possible at the distances noted below during certain times of the year or

day. Radio interference may also cause problems with reception.

Mainﬂ ingen (Germany) or Anthorn (England) transmitters: 500 kilometers (310 miles)

Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)

Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)

Shangqiu (China) transmitter: 500 kilometers (310 miles)

• As of December 2012, China does not use Daylight Saving Time (DST). If China does go to the Daylight

Saving Time system in the future, some functions of this watch may no longer operate correctly.

To get ready for a receive operation

1. Conﬁ rm that the watch is in the Timekeeping Mode or World Time Mode. If it isn’t, use

D to enter the

Timekeeping Mode or World Time Mode (page E-26).

2. The antenna of this watch is located on its 12 o’clock side. Position the watch with 12 o’clock facing

towards a window as shown in the nearby illustration. Make sure there are no metal objects nearby.

• Signal reception normally is better at night.

• The receive operation takes from two to ten minutes, but

in some cases it can take as long as 20 minutes. Take

care that you do not perform any button operation or

move the watch during this time.

12 o’clock

E-18

• Signal reception may be difﬁ cult or even impossible under the conditions described below.

Inside or

among

buildings

Inside a

vehicle

Near

household

appliances,

ofﬁ ce

equipment,

or a mobile

phone

Near a

construction

site, airport

Near

high-tension

power lines

Among or

behind

mountains

3. What you should do next depends on whether you are using auto receive or manual receive.

• Auto receive: Leave the watch over night in the location you selected in step 2. See “Auto Receive”

below for details.

• Manual receive: Perform the operation under “To perform manual receive” on page E-19.

Auto Receive

• With auto receive, the watch performs the receive operation each day automatically up to six times (up

to ﬁ ve times for the Chinese calibration signal) between the hours of midnight and 5 a.m. (according to

the Timekeeping Mode time). When any receive operation is successful, none of the other receive

operations for that day are performed.

• When a calibration time is reached, the watch will perform the receive operation only if it is in the

Timekeeping Mode or World Time Mode. The receive operation is not performed if a calibration time is

reached while you are conﬁ guring settings.

E-19

• You can use the procedure under “To turn auto receive on and off” (page E-22) to enable or disable

auto receive.

To perform manual receive

1. Use D to select the Receive Mode (R/C) as shown on page E-26.

2. Hold down A until RC Hold appears on the display and then

disappears.

• A signal level indicator (L1, , or L2 L3, see page E-21) will appear

on the display after reception starts. Do not allow the watch to

move and do not perform any button operation until GET or ERR

appears on the display.

• If the receive operation is successful, the reception date and time

appear on the display, along with the GET indicator.

The watch will return to the Timekeeping Mode if you press

D or

if you do not perform any button operation for about two or three

minutes.

Receiving

Receiving indicator

Receive successful

Receiving

Receiving indicator

Receive successful

E-20

• If the current reception fails but a previous reception (within the

last 24 hours) was successful, the display shows the receiving

indicator and the ERR indicator. If the ERR indicator only is

displayed (without the receiving indicator), it means that all of the

receive operations over the past 24 hours have failed.

The watch will return to the Timekeeping Mode without changing

the time setting if you press D or if you do not perform any button

operation for about two or three minutes.

Note

• You can interrupt a time calibration signal reception operation by

pressing any button.

Receive failed

If there was a previously

successful reception

Receive failed

If there was a previously

successful reception

E-21

Signal Level Indicator

During manual receive, the signal level indicator displays the signal level

as shown below.

Weak (Unstable) Strong (Stable)

The level indication will change in accordance with reception conditions

while reception is being performed.

As you watch the indicator, keep the watch in a location that best

maintains stable reception.

• Even under optimum reception conditions, it can take about 10

seconds for reception to stabilize.

• Note that weather, the time of day, surroundings, and other factors all

can affect reception.

E-22

To check the latest signal reception results

Enter the Receive Mode (page E-26).

• When receive is successful, the display shows the time and date that

receive was successful. - : - - indicates that none of the reception

operations were successful.

• To return to the Timekeeping Mode, press D.

To turn auto receive on or off

1. Enter the Receive Mode (page E-26).

2. Hold down E for at least two seconds. Release E after AUTO

appears. This is the setting screen.

• Note that the setting screen will not appear if the currently selected

Home City is one that does not support time calibration reception.

3. Press A to toggle auto receive between on (On ) and off (

OFF).

4. Press E to exit the setting screen.

On/Off statusOn/Off status

E-23

Radio-controlled Atomic Timekeeping Precautions

• Strong electrostatic charge can result in the wrong time setting.

• Even if a receive operation is successful, certain conditions can cause the time setting to be off by up

to one second.

• The watch is designed to update the date and day of the week automatically for the period January 1,

2000 to December 31, 2099. Updating of the date by signal reception will no longer be performed

starting from January 1, 2100.

• If you are in an area where signal reception is not possible, the watch keeps time with the precision

noted in “Speciﬁ cations”.

• The receive operation is disabled under any of the following conditions.

– While power is at Level 3 (L) or lower (page E-11)

– While the watch is in the power recovery mode (page E-13)

– While a direction, barometric pressure/temperature, or altitude reading operation is in progress

– When the watch is in the function sleep state (“Power Saving”, page E-14)

– While the barometric pressure change indicator is displayed

– While a countdown timer operation is in progress (page E-79)

• A receive operation is cancelled if an alarm sounds while it is being performed.

• The Home City setting reverts to the initial default of TYO

(Tokyo) whenever the battery power level

drops to Level 5 or when you have the rechargeable battery replaced. If this happens, change the

Home City to the setting you want (page E-31) .

Operation Guide 3410

Specyfikacje produktu

Marka:	Casio
Kategoria:	zegarek
Model:	G-Shock GW-9400-3ER
Materiał obudowy:	Żywica
Wysokość produktu:	55.2 mm
Szerokość produktu:	53.5 mm
Głębokość produktu:	18.2 mm
Waga produktu:	80 g
Elektryczny kompas:	Tak
Rodzaj baterii:	CTL1616
Liczba baterii:	1
Wodoodporny:	Tak
Typ mechanizmu:	Kwarc (słoneczny)
Odporny na wstrząsy:	Tak
Chronograf:	Nie
Funkcja alarmu:	Tak
Kalendarz:	Tak
Typ zegarka:	Zegarek z bransoletką
Kolor obudowy:	Zielony
Tworzywo paska:	Żywica
Kolor główny paska:	Zielony
Kształt koperty:	Okrągły
Kolor tarczy zegarka:	Czarny
Styl oznaczenia godzin i minut:	Liczby arabskie
Konstrukcja produktu:	Sport
Podświetlenie LED:	Tak
Funkcja wstrzymania:	Tak
Tryb zegarka:	12 h/24 h
Głębokość wodoszczelności:	200 m
Wskaźnik poziomu baterii:	Tak
Barometr:	Tak
Wysokościomierz:	Tak
Typ szkła:	Mineralny
Dedykowana płeć:	Męski
Funkcja world time:	Tak
Odbiornik sygnału radiowego:	EU, USA, Japan, China
Wodoszczelność:	20 ATM
Timer:	Tak