Instrukcja obsługi Canon EF-M 55-200mm f/4.5-6.3 IS STM

Canon soczewka EF-M 55-200mm f/4.5-6.3 IS STM

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Canon EF-M 55-200mm f/4.5-6.3 IS STM (4 stron) w kategorii soczewka. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

ENG-1

❶

❷

❹

❸

Wide end

Telephoto end

Zoom ring

ENG EF-M LENS Instructions

EF-M55-200mm f/4.5-6.3 IS STM

①

②

③

④⑤

⑥

⑦

Nomenclature

① Focusing ring

② Hood mount

③ Filter Mounting Thread

④ Lens mount index

⑤ Contacts

⑥ Zoom position index

⑦ Zoom ring

Thank you for purchasing a Canon product.

The Canon EF-M55-200mm f/4.5-6.3 IS STM lens is a

telephoto zoom lens developed for digital cameras compatible

with EF-M lenses*.

* Only the following cameras are compatible with EF-M lenses (as

of February 2014):

EOS M, EOS M2*1

*1: Not available in certain countries and regions.

• "IS" stands for Image Stabilizer.

• "STM" stands for stepping motor.

Safety Precautions

• Do not look at the sun or a bright light source through the

lens. Doing so could result in vision loss or blindness.

• Whether it is attached to the camera or not, do not leave

the lens under the sun without the lens cap attached. This

is to prevent the lens from concentrating the sun’s rays, which

could cause a fire.

Handling Cautions

• If the lens is taken from a cold environment into a warm

one, condensation may develop on the lens surface and

internal parts. To prevent condensation in this case, first

put the lens into an airtight plastic bag before taking it from a

cold to warm environment. Then take out the lens after it has

warmed gradually. Do the same when taking the lens from a

warm environment into a cold one.

• Do not leave the lens in excessive heat such as in a car in

direct sunlight. High temperatures can cause the lens to

malfunction.

• Please also refer to the handling cautions found in your

camera’s instructions.

Conventions used in this instruction

Warning to prevent lens or camera malfunction or

damage.

Supplementary notes on using the lens and taking

pictures.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Do not make any changes or modifications to the equipment unless

otherwise specified in the instructions. If such changes or modifications

should be made, you could be required to stop operation of the

equipment.

This equipment has been tested and found to comply with the limits for

a class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to

radio communications.

However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAN ICES-3 (B) / NMB-3 (B)

1. Mounting and Detaching the Lens

See your camera’s instructions for details on mounting and

detaching the lens.

• After detaching the lens, place the lens with the rear end

up to prevent the lens surface and contacts from getting

scratched. (fig. )❶

• If the contacts get soiled, scratched, or have fingerprints on

them, corrosion or faulty connections can result. The camera

and lens may not operate properly.

• If the contacts get soiled or have fingerprints on them, clean

them with a soft cloth.

• If you remove the lens, cover it with the dust cap. To attach

it properly, align the lens mount index and the index of the 

dust cap as shown in the diagram, and turn clockwise. (fig. ) ❷

To remove it, reverse the order.

2. Zooming

Turn the lens’ zoom ring to adjust the size of the photo field or

subject. (fig. )❸

• For wider shots, turn the zoom ring toward the wide end.

• For closer shots, turn the zoom ring toward the telephoto end.

• Be sure to finish zooming before focusing. Zooming after

focusing can affect the focus.

• Blurring may temporarily occur if the zoom ring is quickly

rotated.

• Zooming during still image exposure will result in delayed

focus. This causes any streaks of light that are captured

during exposure to be blurred.

3. Manual Focus

When the camera’s focus mode is set to [MF], focus manually by

turning the focusing ring (fig. ).❹

Quickly rotating the focusing ring may result in delayed focus.

• Focus mode is set using the camera. Please refer to the

camera’s instructions.

• After autofocusing in [AF+MF] mode, focus manually by

pressing the shutter button halfway and turning the focusing

ring (full-time manual focusing).

4. Image Stabilizer

This lens is equipped with an Image Stabilizer. This function

corrects camera shake, allowing users to capture sharp images.

Also, the Image Stabilizer automatically provides optimal image

stabilization depending on shooting conditions (such as shooting

still subjects and following shots). Please set the Image Stabilizer

ON or OFF using the camera settings. See your camera’s

instructions for details.

• The Image Stabilizer cannot compensate for a blurred shot

caused by a subject that moved.

• The Image Stabilizer may not be fully effective if you shoot

from a violently shaking vehicle or other transportation.

• The Image Stabilizer consumes more power than normal

shooting, resulting in fewer shots and a shorter movie

shooting time.

• When shooting a still subject, it compensates for camera

shake in all directions.

• It compensates for vertical camera shake during following

shots in a horizontal direction, and compensates for

horizontal camera shake during following shots in a vertical

direction.

• When you use a tripod, the Image Stabilizer should be

turned off to save battery power.

• Even with a monopod, the Image Stabilizer will be as

effective as during hand-held shooting.

However, depending on the shooting environment, the

Image Stabilizer effect may be less effective.

CT1-8598-000

COPY

ENG-2

❺

0214Ni © CANON INC. 2014

5. Hood (sold separately)

The ET-54B hood cuts out unwanted light and protects the front of

the lens from rain, snow, and dust.

To attach the hood, align the hood’s attachment position mark with

the red dot on the front of the lens, then turn the hood as shown

by the arrow until the lens’ red dot is aligned with the hood’s stop

position mark. (fig. )❺

The hood can be reverse-mounted on the lens for storage.

• If the hood is not attached properly, vignetting (darkening of

the perimeter of the picture) may occur.

• When attaching or detaching the hood, grasp the base of

the hood to turn it. To prevent deformation, do not grasp the

rim of the hood to turn it.

6. Filters (sold separately)

You can attach filters to the filter mounting thread on the front of

the lens.

Only one filter may be attached.

Specifications

Focal Length/Aperture 55-200mm f/4.5-6.3

Lens Construction 11 groups, 17 elements

Minimum Aperture f/22-32

Angle of View

Diagonal: 27°50'-7°50'

Vertical: 15°40'-4°20'

Horizontal: 23°20'-6°30'

Min. Focusing Distance 1.0m/3.28ft

Max. Magnification 0.21x (at 200 mm)

Field of View

Approx. 248x375-73x109 mm/

9.76x14.76-2.87x4.29 inch

(at 1.0 m/3.28 ft.)

Filter Diameter 52 mm

Max. Diameter and Length 60.9x86.5 mm/2.40x3.41 inch

Weight Approx. 260 g/9.2 oz

Hood ET-54B (Sold Separately)

Lens Cap E-52 II

Dust Cap Lens Dust Cap EB

Case LP816 (Sold Separately)

• Equivalent to 88-320 mm in the 35mm film format.

• The lens length is measured from the mount surface to the front

end of the lens. Add 20 mm when including the lens cap and

dust cap.

• The size and weight listed are for the lens only, except as

indicated.

• Extenders cannot be used with this lens.

• Aperture settings are specified on the camera. The camera

automatically compensates for variations in the aperture setting

when the camera is zoomed in or out.

• All data listed is measured according to Canon standards.

• Product specifications and appearance are subject to change

without notice.

COPY

Specyfikacje produktu

Marka:	Canon
Kategoria:	soczewka
Model:	EF-M 55-200mm f/4.5-6.3 IS STM
Kolor produktu:	Czarny
Waga produktu:	260 g
Przeznaczenie:	SLR
Kompatybilność:	Canon
Długość ogniskowa:	55 - 200 mm
Stabilizator obrazu:	Tak
Struktura soczewki:	17/11
Wielkość filtra:	52 mm
interfejs mocowania obiektywu:	Canon EF-M
Najmniejsza odległość ogniskowa:	1 m
Średnica:	60.9 mm
Długość produktu:	86.5 mm
Kąt widzenia obiektywu, w poziomie:	6.5 °
Kąt widzenia obiektywu w pionie:	4.33 °
Kąt widzenia soczewki, przekątna:	27.86 - 7.86 °
Maksymalna przesłona:	32
Minimalna przesłona:	4.5
Minimalna ogniskowa (35mm equiv):	88 mm
Maksymalna ogniskowa (35mm equiv):	320 mm
Maksymalne powiększenie:	0.21 x
Typ obiektywu:	Standardowy obiektyw zmiennoogniskowy
Liczba elementów przysłony:	7
Format czujnika obrazu:	APS-C
Napęd AF:	STM