Instrukcja obsługi Bretford CoreX

Bretford Niesklasyfikowane CoreX

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Bretford CoreX (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
CAPACITY per slot width 1.00” 1.25” 1.50” ! ! !
TCOREX24 2 shelves! ! 24 20 devices ! !
TCOREX36 3 shelves! ! 36 30 devices ! !
TCOREX45 3 shelves 45 36 30 devices ! ! ! !
COMPATIBILITY Designed for various sized laptops & chromebooks, yet versatile enough to
support most tablets. Uses the device manufacturer supplied AC power cord and adapter.
! "OUTSIDE DIMENSIONS 29.50”W x 26.00”D x 44.75”H
! ! "SLOT DIMENSIONS 1.25” or 1.50” W x 17”D x
! ! 12.00”H for TCOREX24"
! ! 10.00”H for TCOREX36"
! ! 1.00” or 1.25” or 1.50”W x 17”D x"
! ! 10.00”H for TCOREX45"
!WEIGHT WITHOUT DEVICES!TCOREX24 163 pounds! "
! ! TCOREX24B 170 pounds! "
! ! TCOREX36 175 pounds! "
! ! TCOREX36B 182 pounds! "
! ! TCOREX45 185 pounds! "
! ! TCOREX45B 192 pounds! "
! "POWER MANAGER!Digital
!POWER REQUIREMENTS !100 -125V ac, 12A, 50/60Hz;
!SHIPPING Ships fully assembled, ready to load devices
!WARRANTY For product specific warranty information,
! ! please visit: bretford.com/warranty
USER GUIDE
CoreX Carts
TCOREX24 CoreX Charging Cart AC for up to 24 devices w/Back Panel !
TCOREX24B CoreX Charging Cart AC for up to 24 devices w/Rear Door !
TCOREX36 CoreX Charging Cart AC for up to 36 devices w/Back Panel !
TCOREX36B CoreX Charging Cart AC for up to 36 devices w/Rear Door !
TCOREX45 CoreX Charging Cart AC for up to 45 devices w/Back Panel !
TCOREX45B CoreX Charging Cart AC for up to 45 devices w/Rear Door!
Part # 031-10608 rev December 2016
MADE IN USA
with globally
sourced products
www.bretford.com
Technical Specifications
POWER SWITCH
Located on the
left side of the
cabinet, in the
Power Cord
Shroud
DIRECTIONAL LOCK CASTERS
When engaged, keep the
cart rolling in the right
direction. When
unengaged, allow the cart
to be easily maneuvered
into small spaces. Marked
with a Green Locking Tab
CORD PASS-THRU ON TOP
Allows devices to be
powered outside of the
cart, while their power
cords are plugged
inside the cart.
Front View
Rear View
REAR SECURITY PANEL
VERSION
Can be securely held
in place with Security
Bolts. Panel easily lifts
off to expose the back
of the cart, where the
adapters and cord
sets are kept in cable
bins.
DOOR LOCK SHROUD
Protects the padlock
and the locking
handle during
transport
WARNING:
This cart is not intended
to hold items on the top
surface. Do not place
any item weighing more
than 1 pound on the top
surface of the cart to
avoid damage.
INTEGRATED HANDLE
Handle integrated into
the top of the cart for
pushing and moving
the cart.
USER GUIDE | CoreX CARTS
SETTING THE COMBINATION LOCK
Your new COREX Cart comes equipped with a resettable Combination Padlock. You can program the
lock with your own combination. The lock starts with 0-0-0-0. Follow the directions with the look for
changing the combination. Remember to depress the shackle before un-engaging it from the lock.
AUXILIARY OUTLET CORD
This plugs into its own IEC outlet,
and provides the power for the
cord pass-thru.
NOTICE: This auxiliary outlet
provides a maximum 2 amps.
General Use
REAR LOCKING DOOR
VERSION
Hinged rear door
provides easy access
to the back of the cart.
Door locks in place
with a key. Keys found
in the Hardware Pack.
Rear Access
Versions
Changing the Slot Width
from 1.00” to 1.25” to 1.50”
USER GUIDE | CoreX CARTS
Device Storage & Cable Management
1. Rear Security Panel Versions: At the back of the cart, unscrew the two Thumb
Screws on both sides of the cart. Lift the back panel off of the chassis. This exposes
the power outlet modules for each of the shelves.
Rear Locking Door Versions: Using the keys from the Hardware Pack, unlock the
Rear Door and swing open to reveal the power outlet modules for each of the shelves.
2. Starting in the rear of the cart with the back panel removed, insert a power adapter in
the storage bin for the associated device storage shelf (top, middle or bottom).
3. Measure the amount of cable necessary to reach from the power adapter located in the
bin to the front of the cart (over the AC outlet box, from the back to the front of the cart,
through the cable management hooks). Leave sufficient slack for the power connector
to plug into the device.
4. Plug the device AC adapter plug into one of the outlets nearest to where the power
adapter is located in the bin.
5. Repeat the above process for the total number of devices’ power adapters & cable sets.
6. In the front of the cart, insert a device into each of the slots, and plug in the power
connector to each device.
7. Replace the Back Panel and either reinsert the Thumb Screws, or insert the Security
Screws from the Hardware Pack (using the Security Bit, also in the Hardware Pack).
8. Place the cart near a wall outlet and plug the cart in.
9. Turn on the power switch - located in the front of the cord winder shroud
10. Once the cart is turned on, the power manager begins rotating power to the power
strips very 5 minutes. This allows efficient charing of the devices in the cart from one
single 15 amp circuit.
1. Unscrew the Thumb Screws - one on
each side of the cart at the back. Lift o the ff
Back Panel.
1
TCOREX24
TCOREX36
rear view of the power outlet modules"
2-5. Plug adapters in & thread power
connectors to the front of the cart
front view of the
dividers & slot ID
numbers"
6. Hang the
power
connectors
above the slots
using the slots
hooks provided
1. Slot
2. Tabs located at the front of the plastic device platforms on each of the
shelves can be depressed, and the platform lifts out of the cart.
3. Flip the device platform over, and remove each of the plastic dividers by
“pinching” the divider tabs that stick thru the platform.
4. Reinsert the dividers into the square slots which create the 1.5” slot width.
(see the closeup at the left of the underside of the platform.)
5. Flip the device platform upright and reinsert into the shelf.
6. The slot number indicator can now be repositioned at “10”, replacing “12”
….. “20” replacing #24” and “30” replacing “36”
1.00”
1.25”
1.50”
closeup underside of device platform
Security Screws & Security Bit included in
hardware pack. Your choice to use the
Security Screws.
1. Slot widths ship automatically at
the 1.25” width for the
TCOREX36 & TCOREX24,
1.00” for the TCOREX45. If your
devices need the larger width,
follow these simple directions.
7

Specyfikacje produktu

Marka: Bretford
Kategoria: Niesklasyfikowane
Model: CoreX

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Bretford CoreX, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Bretford

Bretford

Bretford Explorer ETCPRMDL Instrukcja

5 Października 2024
Bretford

Bretford Explorer ETCSM-SB Instrukcja

5 Października 2024
Bretford

Bretford Explorer ETCDS-SB Instrukcja

5 Października 2024
Bretford

Bretford Explorer ETCHNDL-SB Instrukcja

5 Października 2024
Bretford

Bretford Cube TVS10AC Instrukcja

1 Października 2024
Bretford

Bretford CoreX Instrukcja

1 Października 2024
Bretford

Bretford HE405BG2 Instrukcja

1 Października 2024
Bretford

Bretford CUBE Transport Cart Instrukcja

1 Października 2024
Bretford

Bretford HE406BG2 Instrukcja

1 Października 2024
Bretford

Bretford CUBE Cart Mini Instrukcja

1 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024