Instrukcja obsługi Bresser OMNI-5

Bresser nieskategoryzowany OMNI-5

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Bresser OMNI-5 (3 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/3
OMNI-5
RED/GREEN LOW PROFILE SIGHT INSTRUCTIONS
CAUTION: BEFORE YOU BEGIN, ENSURE THAT THE FIREARM IS CLEAR. REMOVE MAGAZINE,
LOCK ACTION OPEN AND VISUALLY INSPECT TO ENSURE THAT THE CHAMBER IS CLEAR.
PRODUCT SPECIFICATIONS
POWERING UP AND POWERING DOWN THE RED DOT
Depress and release the or button to power up the red dot; press and button “+” “-” “+” “-”
to power down the red dot. Press to change color between red and green. This red dot “C”
has a convenient auto-off feature that will switch off the device if it has been left on for
more than 4 hours. If the unit shuts down automatically, moving or lifting the gun will turn
the unit on again automatically. However, if the unit is turned off by pressing and “+” “-”
simultaneously, the unit will not be turned on automatically by moving or lifting the gun.
ADJUSTING BRIGHTNESS
Press the or button and select the lowest brightness setting that still provides good “+” “-”
contrast against the target. The higher brightness settings should only be used in bright
daylight (otherwise, the reticle may appear distorted).
BATTERY
Your sight includes a 3-volt lithium battery (CR2032). To replace the battery, rotate the
battery cover counter-clockwise and remove. Insert the replacement battery with side “+”
facing out. Replace the cover and hand-tighten.
INSTALLATION
CAUTION: BEFORE YOU BEGIN, ENSURE THAT THE FIREARM IS CLEAR. REMOVE MAGAZINE,
LOCK ACTION OPEN AND VISUALLY INSPECT TO ENSURE THAT THE CHAMBER IS CLEAR.
To get the best performance from your red dot, it must be mounted properly. If you are not
familiar with mounting a red dot, it is strongly recommended that you seek the assistance of
a qualied professional.
MOUNT ONTO A PICATINNY OR WEAVERSTYLE RAIL
Your sight has integrated mounting rails that attach to a standard Weaver-style base or
Picatinny rail.
Loosen both mounting screws and set the sight onto the mounting base of the rearm.
Please note that one mounting screw is lower than the other mounting screw. Only the
lower mounting screw should t into one of the grooves in the top of the mounting base.
Be sure the sight is fully seated on the mounting base before tightening the mounting
screws. To ensure tightening, alternate between screws after each half turn.
( DO NOT OVER TIGHTEN MOUNTING HARDWARE. MAX. TORQUE 20 INCH LBS. )
For additional security, a drop of thread-locker can be added to the mounting screws.
PARALLAX
Your sight has been carefully set to have a minimum parallax at 30 yards. At distances
signicantly greater or less than this distance, some parallax will be observed. To reduce the
possibility of a Point if Impact (POI) shift caused by parallax, the reticle should be kept in the
middle 2/3 of the eld of view when aiming.
ZEROING
Initial Setup
The dot position has been pre-set at the factory. Only minor windage and elevation
adjustments should be required. If possible, a bore sighting device should be used for rough
alignment of the sight to the rearm. If bore sighting is not possible, place the rearm on
a sturdy rest and look through the barrel or along the rail at a small target about 25 yards
away. Turn on the red dot and select a suitable brightness. Using a straight-slot screwdriver,
adjust the windage and elevation until the dot position corresponds with the target. Note
the following when making adjustments.
Click value: 1 MOA (approximately 1” at 100 yards; ¼” at 25 yards)
Windage: Counterclockwise (indicated by arrow) moves point of impact right/clockwise, left.
Elevation: Counterclockwise (indicated by arrow) moves point of impact up/clockwise, down.
FINAL SETUP (LIVE FIRE)
CAUTION: USE ADEQUATE EYE AND EAR PROTECTION AT ALL TIMES. SHOOT ONLY AT AN
APPROVED RANGE OR SUITABLE SAFE AREA.
CAUTION: IF YOU HAVE USED A BORE SIGHTER, CONFIRM THAT THE BORE SPUD IS NO
LONGER IN THE MUZZLE AND THAT THE BORE IS UNOBSTRUCTED.
Position the target no further than 25 yards away to begin the zeroing process. Turn on
the red dot and select a suitable brightness. Carefully re three shots and note where they
strike on the target. Your group should strike the target no greater than 10” from your point
of aim. (Should the group be farther away than this, the mounting process is faulty and
must be corrected before proceeding.) Make adjustments to windage and elevation so that
your group strikes the target approximately 1” beneath the point of aim with no windage
error (at six o’clock, neither left nor right).
When complete, position the target at the desired zero distance. Fire three rounds at this
distance and adjust as necessary to hit dead-on.
RETICLE
Your sight uses a 2 MOA reticle pattern. One MOA is about 1” at a distance of 100 yards (or
3/4” at 75 yards, 1/2” inch at 50 yards, etc.).
FLIP-UP LENS CAPS
This model includes flip-up lens caps. These lens caps are intended to protect the optical
glass from inclement weather and dust. While impervious to many chemicals, care should be
taken to avoid contact with powerful solvents and chemicals.
MIRROR ANGLE
The mirror-lens can be easily seen when looking through the wrong end of the sight. The tilt
of the mirror-lens is not a defect. It is tilted to reflect the LED’s light back to the user’s eye.
The OMNI-5 red dot sight may be mounted in two congurations:
LOW PROFILE MOUNT HIGH CO-WITNESS MOUNT
Flip Up Cap
Flip Up Cap
Mounng Screws
Baery Cover
Elevaon Adjustment
Windage Adjustment
Power/Brightness
Control
Model 23-20300
Description Red/Green Low
Prole Sight
Magnication 1x
Length 4.8”
Width 2.4”
Height (low/high) 2.3”/2.8”
Optical Height
(low/high)
1.1”/1.4”
Weight (low/high) 0.7lbs/0.75lbs
Power Supply CR2032 3V
Lithium Battery
Brightness 1 - 11
Windage 40 MOA
Elevation 40 MOA
Click Value 1 MOA
Accessories Picatinny Mount
4 Mounting Screws
2mm Hex Wrench
3mm Hex Wrench
2 MOA
Continue on back
Cut and mail in
Register your product.
Learn about the full range of service your warranty provides.
Registering online is quick and easy!
https://explorescientificusa.com/product-registration
For products that do not include a serial number, use the product item number followed by the date of purchase
expressed in a six-digit format. For example, a purchase date of January 1, 2018, would be entered as 010118.
Model numbers: Serial numbers:
FOLD FOLD FOLD FOLD4.25 IN
5.5 IN
MAINTENANCE & CLEANING
Although your red dot is extremely durable, it is a precision instrument that should be
treated with reasonable care.
LENSES
The optical coatings are hard and will last indenitely with proper care.
Should either protective windows become dirty, blow loose materials off before cleaning.
Use lens cleaning fluid and a soft cloth to dab at the surface and remove any abrasive bits
of dust and dirt before applying more pressure. Be patient and clean in steps so as to not
grind abrasive dirt into the lens.
EXTERIOR
Should the exterior become dirty, it may be cleaned with a damp cloth. Do not use oil or
solvents as they may be harmful if inadvertently rubbed onto the optical coatings.
STORAGE
This red dot has been constructed using adhesives and lubricants that enable a broad range
of operational and storage environments. The grease used is temperature-stable from -50 to
+175 degrees Fahrenheit. Do not store at temperatures outside this range
(for example a car trunk on a very hot day).
TROUBLESHOOTING
Please use the following guide to test/correct operational issues with this red dot.
1. Red dot will not power up.
A. Check to see that the battery is properly installed with side facing down.“+”
B. Replace battery.
C. Inspect battery terminals for corrosion or debris inhibiting contact and
correct as necessary.
D. Should the above be ineffective in resolving the problem,
contact Bresser ( call 866.252.3811 or visit explorescientic.supportsync.com )
for return procedures.
2. Red dot brightness will not adjust.
A. Move to where ambient light is low enough to clearly discern a change in brightness.
B. Follow fault diagnosis #1A-C above and repeat 2A. If brightness will not adjust,
contact Bresser ( call 866.252.3811 or visit explorescientic.supportsync.com )
for return procedures.
3. Red dot will not zero.
Review sections of this manual regarding zeroing. ( See ZEROING in this manual. )
This red dot is pre-centered at the factory; if more than 10” of adjustment is required at
a sight-in distance of 25 yards, mounting is at fault.
4. Red dot will not adjust for windage and/or elevation
This red dot has a maximum adjustment range of 30 MOA. Beyond this range of adjustment,
rotating the W/E screws will not provide additional point of impact change. If you believe that
your red dot is within the maximum range of adjustment and not providing W/E movement,
contact Bresser ( call 866.252.3811 or visit explorescientic.supportsync.com )
for return procedures.
5. Red dot appearance and/or target is not clear.
A. Be sure to select the lowest brightness setting that still provides good contrast against
the target; using too high a setting may make the reticle appear distorted.
B. Inspect both sides of the main lens for contamination and clean as necessary.
( See MAINTENANCE & CLEANING in this manual. )
C. Inspect the protective window in front of the diode and clean as necessary.
( See MAINTENANCE & CLEANING in this manual. )
D. Should the above be ineffective in resolving the problem,
contact Bresser ( call 866.252.3811 or visit explorescientic.supportsync.com )
for return procedures.
_________________________________________________________________________________
LIMITED FIVE YEAR WARRANTY
With a mission to make outdoor and scientific exploration accessible and
affordable, EXPLORE SCIENTIFIC has been putting people on a path to
adventure since 2008. A huge part of ensuring that our customers have the
experiences they seek is providing unwavering support and product protection.
Upon receipt of your product, we encourage you to thoroughly inspect it, promptly register it and familiarize
yourself with the applicable warranty coverage as outlined below. If you have any questions or concerns about your
product and its warranty or if you need advice on getting started, please contact us at 1-866-252-3811.
Registering Your Product:
To maximize the warranty coverage provided by EXPLORE SCIENTIFIC, it is important that you promptly register
your product either by mailing in the enclosed card to 1010 South 48th Street, Springdale, AR 72762 or by visiting
https://explorescientificusa.com/product-registration.
If registered within 60 days of purchase, your product will have additional warranty protection against manufacturer
defects. When you purchase an EXPLORE SCIENTIFIC product, you will notice that there are serial numbers on most
telescopes, microscopes, binoculars, riflescopes, eyepieces, and other major components or educational products.
Please use this number to register your item. For products that do not include a serial number, use the product item
number followed by the date of purchase expressed in a six-digit format. For example, a purchase date of January
1, 2018, would be entered as 010118.
Return Authorization: Making it Easy
We know that your time is precious, so we aim to eliminate the hassle of obtaining an authorization to send in your
product for repairs or service. Once you have registered your product, you may visit our online customer service
center ( ) and submit a request for warranty service. This will generate all https://explorescientific.supportsync.com
the required RMA (Return Merchandise Authorization) information. Prior to the return of any product or part, you
must be registered as the current owner, and your Return Merchandise Authorization (RMA) number must be on the
outside of the box. If you need help in using your Return Merchandise Authorization (RMA) number,
please call us at 1-866-252-3811.
Each returned product or part shipped to EXPLORE SCIENTIFIC must include the RMA number, a written statement
detailing the nature of the claimed defect, as well as your name, return shipping address, and a phone number
where we and/or the carrier returning your product can reach you. If the return occurs within 30 days of the
purchase date, contact our Customer Service Department to receive a prepaid return label to cover shipping costs
related to returning the product to our facility.
If it has been more than 30 days since the item was purchased, customers are responsible for shipping costs
related to returning the product to our facility. In the event, that you must return product to EXPLORE SCIENTIFIC,
we recommend that you use a carrier that offers shipment tracking for all returns and insure your package for safe
return to EXPLORE SCIENTIFIC so that you are completely protected if the shipment is lost or damaged in transit. If
you choose not to (1) use a carrier that offers tracking or (2) insure or declare the full value of the product, you will
be responsible for any lost shipment.
Warranty Coverage Periods By Product:
EXPLORE SCIENTIFIC warranties our products to be free from defects in materials and workmanship for a specified
period based on product type. EXPLORE SCIENTIFIC will repair or replace such product or part thereof that upon
inspection by EXPLORE SCIENTIFIC, is found to be defective in materials or workmanship. As a condition to the
obligation of EXPLORE SCIENTIFIC to repair or replace such product, the product must be returned to EXPLORE
SCIENTIFIC together with proof-of-purchase and product registration satisfactory to EXPLORE SCIENTIFIC.
Warranty periods by product brand and type are:
EXPLORE SCIENTIFIC Branded Telescopes: *Limited* USA One Year Warranty once registered within 60 days
EXPLORE SCIENTIFIC Branded Eyepieces: *Limited* USA Five Year Warranty once registered within 60 days
EXPLORE SCIENTIFIC Branded Electronics & Non-Electronic Telescope Accessories: *Limited* USA One Year
Warranty once registered within 60 days
The warranty periods listed below apply to the following branded products:
FirstLight, Bresser, Alpen, Explore One, National Geographic, Discovery
Telescopes: *Limited* USA One Year Warranty once registered within 60 days
Microscopes: *Limited* USA One Year Warranty once registered within 60 days
Riflescopes: *Limited* USA Five Year Warranty once registered within 60 days
Binoculars & Spotting Scopes: *Limited* USA Five Year Warranty once registered within 60 days
Laser Rangefinders, Cameras and Electronics: *Limited* USA One Year Warranty once registered within 60 days
Third-Party Products: Warranty is provided by Third Party Manufacturers
Limited Warranty is in the USA, USA territories and Canada. For full warranty protection, the product must be
registered within 60 days of purchase.
The Details
USA Limited Product Warranty for Products Purchased in the USA and Canada
EXPLORE SCIENTIFIC LLC is the owner and assumes liability for all USA warranties of EXPLORE SCIENTIFIC. During
the applicable warranty period, EXPLORE SCIENTIFIC will repair or replace the product, or part thereof, found upon
inspection by EXPLORE SCIENTIFIC to be defective, provided the defective part or product is returned to EXPLORE
SCIENTIFIC LLC, freight prepaid, with verification of product registration. EXPLORE SCIENTIFIC products purchased
outside the United States and Canada are not included in this warranty, but are covered under separate warranties
issued by authorized EXPLORE SCIENTIFIC International Distributors.
Non-EXPLORE SCIENTIFIC Branded/Third-Party Products
If you discover what you believe is a defective product or software from any third-party product, please contact the
manufacturer of such third-party product directly for information regarding the manufacturer’s warranty. Please
note that products or software sold through the EXPLORE SCIENTIFIC online store that do not bear the EXPLORE
SCIENTIFIC name or are not EXPLORE SCIENTIFIC’s brands produced products are serviced and supported
exclusively by their manufacturers in accordance with the terms and conditions packaged with the products.
EXPLORE SCIENTIFIC’s warranties do not apply to products that are not EXPLORE SCIENTIFIC’s brands, or other
EXPLORE SCIENTIFIC produced products, even if packaged or sold with EXPLORE SCIENTIFIC products.
Silver Grade Products
EXPLORE SCIENTIFIC products purchased through our Silver Grade program are covered for the same warranty
protection periods outlined above in regard to functional and/or optical defects. Cosmetic issues such as dents and
blemishes are not covered as these issues are inherent to the Silver Grade designation.
Disclaimer
This warranty is not valid in cases where the product has been abused or mishandled or where unauthorized repairs
have been attempted or performed. EXPLORE SCIENTIFIC specifically disclaims special, indirect, or consequential
damages or lost profits, which may result from a breach of this warranty. Any implied warranties that cannot be
disclaimed are hereby limited to a term of one year from the date of purchase by the original retail purchaser.
EXPLORE SCIENTIFIC reserves the right to change product specifications or to discontinue products without prior
notice. All EXPLORE SCIENTIFIC’s warranties are limited to the original owner. These warranties give you specific
rights. You may have other rights, which vary from state to state.
Customers living outside of the USA, who have purchased an EXPLORE SCIENTIFIC product in the USA, your
warranty is valid within the USA, however, customers returning a product from outside the USA for warranty repair/
maintenance are responsible for shipping fees (customs, fees, duties, etc.) to and from our facility.
Certain state laws do not allow limitations on implied warranties or the exclusion or limitation of certain damages.
If these laws apply to you, some or all of the disclaimers, exclusions or limitations may not apply to you, and you
might have additional rights.
APO/FPO Addresses: If you’re an APO/FPO customer and you’re outside the domestic delivery area, the standard
EXPLORE SCIENTIFIC Warranty Policy applies. However, you are responsible for shipping the product back to a
stateside return address, plus handling, customs, and inventory liability. Since you are responsible for the safe
delivery of any product you are returning to EXPLORE SCIENTIFIC, we recommend that it is insured against loss.
Repurposing: Our Exclusive Product Trade-Up Program
As an owner of an EXPLORE SCIENTIFIC product, you may find that it is time to grow in your exploration and
you would like to trade up for a higher performance product. For a selection of products, we do offer a trade-up
program. To find out if your product qualifies or for additional details, please contact our Customer Service team at
1-866-252-3811. This program is for EXPLORE SCIENTIFIC products purchased from authorized dealers in the U.S.
and Canada or direct from us.
Join the Explore Care Alliance!
If you are interested in additional product protection options, EXPLORE SCIENTIFIC offers exclusive benefits to
those who become members of the Explore Care Alliance. As a member of this community, you also will have
access to special member pricing, new product previews and more. To find out more about this paid membership
program and its benefits, visit https://explorescientificusa.com/explorecarealliance.
Name
Address
Address 2
City
State/Zip Code
Phone
Email
Date Purchased
Store Name
Would you like to sign up for our
newsletter?
YES NO
Would you like to learn more about our
Explore Care Alliance Program?
YES NO
Please mail to:
Explore Scientific
1010 South 48th Street
Springdale, AR 72762
FOLD FOLD FOLD FOLD4.25 IN
5.5 IN

Specyfikacje produktu

Marka: Bresser
Kategoria: nieskategoryzowany
Model: OMNI-5

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Bresser OMNI-5, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany Bresser

Bresser

Bresser OMNI-5 Instrukcja

4 Sierpnia 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024