Instrukcja obsługi Boston Acoustics Sub10F

Boston Acoustics subwoofer Sub10F

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Boston Acoustics Sub10F (6 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/6
In-Floor Subwoofer
Sub10F
Introduction
In many homes and installations, the deep bass of a powered subwoofer is desired, but often there is
not a suitable location to install a box subwoofer. The Boston Sub10F In-Floor Subwoofer handily solves
this dilemma. Located below the floor and powered by the companion Boston SA1 Subwoofer Power
Amplifier, all that is visible in the listening room is a floor register.
Warning: Always turn off the amplifier when connecting the subwoofer and any other components to
the system.
Note: The Sub10F is an installed product. Installation should only be attempted by professional
installers or those possessing skills in construction, the proper use of hand and power tools, knowledge
of local building and fire codes, and a familiarity with the environment below the floor in which the sub-
woofer will be installed.
Placement
For maximum bass, place the Sub10F so its vent is near a corner or sidewall and is as close to the main
speakers as possible.
Floor Register (Not supplied)
The Sub10F mounts in the floor directly below a floor register. The register should have a minimum air
opening of 3 x 9". Return registers without moving parts should be used. If the register has moving lou-
vers or other moving parts, they will need to be removed to prevent them from rattling.
Floor Thickness
As floors differ in thickness, it is important to measure the depth of the floor register and the thickness
of the floor to confirm that the floor register will not be in contact with the subwoofer’s grille.
2
Location Hazards
It is the nature of low-frequency energy (bass) to make objects vibrate. Care should be taken in planning
the installation of the in-floor subwoofer to minimize the risk of room vibration and noise. Do not locate
the in-floor subwoofer close to lamps or furniture that might rattle or vibrate. Some bass energy will be
heard in the room below the subwoofer. If the ceiling below is finished, ceiling fixtures may rattle or
vibrate.
It is recommended that in the area where the Sub10F is to be mounted, the subfloor is glued to the
joists and extra nails are used to secure the subfloor. Be sure the joists to which the Sub10F is mounted
are securely braced against each other so that the distance between them does not change and they
are not able to move or shift (consult local building codes)
Amplifier Requirements & Wiring
The Sub10F must be used with the Boston SA1 Subwoofer Power Amplifier. Use with any other amplifier
will result in poor performance. One SA1 Power Amplifier can power up to two Sub10F subwoofers.
Only one Sub10F should be connected to each set of terminals on the SA1. If you are installing only one
Sub10F, pre-wire so that a second one can be added, but do not connect the extra set of speaker wires
to the SA1.
Set the equalization switch (EQ-MODE) on the back of the SA1 amplifier to the “ ” position. WeFLOOR
recommend the use of 16-gauge or larger speaker wire with both the Sub10F and SA1.
Service Access
If service is needed, the Sub10F’s woofer can be removed through the access panel on the bottom of
the subwoofer. If there is a finished ceiling below the Sub10F, ideally a door allowing access to the
complete subwoofer enclosure, or at minimum, to the Sub10F’s service panel, should be left in the ceil-
ing below.
3

Specyfikacje produktu

Marka: Boston Acoustics
Kategoria: subwoofer
Model: Sub10F

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Boston Acoustics Sub10F, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje subwoofer Boston Acoustics

Boston Acoustics

Boston Acoustics HPS 12HO Instrukcja

13 Grudnia 2024
Boston Acoustics

Boston Acoustics CPS 12Wi Instrukcja

13 Grudnia 2024
Boston Acoustics

Boston Acoustics CPS 10Wi Instrukcja

13 Grudnia 2024
Boston Acoustics

Boston Acoustics GTuned Instrukcja

13 Grudnia 2024
Boston Acoustics

Boston Acoustics Sub10F Instrukcja

13 Grudnia 2024
Boston Acoustics

Boston Acoustics VSi S8W2 Instrukcja

13 Grudnia 2024
Boston Acoustics

Boston Acoustics Classic CS Sub10 II Instrukcja

13 Grudnia 2024

Instrukcje subwoofer

Najnowsze instrukcje dla subwoofer

OSD Audio

OSD Audio GLS8 Instrukcja

5 Stycznia 2025
Audibax

Audibax DSP18s Instrukcja

5 Stycznia 2025
Audibax

Audibax DSP12s Instrukcja

5 Stycznia 2025
Audibax

Audibax Manhattan 18S Instrukcja

5 Stycznia 2025
Ecler

Ecler LABI1-SB18p Instrukcja

5 Stycznia 2025
OSD Audio

OSD Audio BOM4.1.2 Instrukcja

4 Stycznia 2025
Kenwood

Kenwood Excelon XM1041BL Instrukcja

4 Stycznia 2025
REL Acoustics

REL Acoustics T/9x SE Instrukcja

4 Stycznia 2025
James

James 81ST4 Instrukcja

4 Stycznia 2025
James

James 800PTM Instrukcja

4 Stycznia 2025