Instrukcja obsługi Boss OD-3

Boss nieskategoryzowany OD-3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Boss OD-3 (1 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/1

English

7Equipped with a newly developed “Dual-Stage overdrive circuit.”

7Oers a long sustain that is even more powerful than previous overdrive units.

7Creates a truly natural overdrive sound that oers just the right amount of compression.

Panel Descriptions

Main Features

AC Adaptor

(PSA series; sold separately)

Electric Guitar

LEVEL knob

This adjusts the volume of the eect sound.

OUTPUT jack

Connect an amplier to this jack.

Guitar Amplier

DC IN jack

Accepts connection of an AC Adaptor (PSA series; sold separately). By using an AC Adaptor, you can

play without being concerned about how much battery power you have left.

* We recommend that you keep batteries installed in the unit even though you’ll be powering it with

the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the AC adaptor

gets accidentally disconnected from the unit.

* Use only the specied AC adaptor (PSA-series).

CHECK indicator

This indicator shows whether an eect is ON/OFF, and doubles as the Battery Check

indicator.

The indicator lights when an eect is ON.

* If this indicator goes dim or no longer lights while an eect is ON, the battery is near

exhaustion and should be replaced immediately.

TONE knob

This adjusts the tone.

Rotating the knob counterclockwise makes the sound milder, while

rotating in clockwise makes the sound sharper.

Pedal Switch

This switch turns the eects ON/OFF.

Thumbscrew

When this screw is loosened, the pedal will open, allowing you to change

the battery.

* For instructions on changing the battery, refer to “Changing the Battery.”

DRIVE knob

This adjusts the amount of overdrive.

Rotating it clockwise increases the eect, whereas counterclockwise

rotation reduces the eect.

Owner’s Manual

Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).

After reading, keep the document(s) where it will be available for immediate reference.

* The INPUT jack doubles as power switch.

Power to the unit is turned on when you

plug into the INPUT jack; the power is turned

o when the cable is unplugged. When not

using the eects unit, be sure to disconnect

the plug from the INPUT jack.

INPUT jack

This jack accepts input signals (coming form a guitar, some other electric

or electronic musical instrument, or another eects unit).

Precautions When Connecting

5 Raise the amp volume only after turning on the power to all

connected devices.

5 To prevent malfunction and equipment failure, always turn

down the volume, and turn o all the units before making any

connections.

5 Once the connections have been completed, turn on power to

your various devices in the order specied. By turning on devices

in the wrong order, you risk causing malfunction and/or damage

to speakers and other devices.

When powering up: Turn on the power to your guitar amp last.

When powering down: Turn o the power to your guitar amp rst.

5 Before turning the unit on/o, always be sure to turn the volume

down. Even with the volume turned down, you might hear some

sound when switching the unit on/o. However, this is normal and

does not indicate a malfunction.

Use of Battery

5 A battery is supplied with the unit. The life of this battery may be

limited, however, since its primary purpose was to enable testing.

5 If you handle batteries improperly, you risk explosion and uid

leakage. Make sure that you carefully observe all of the items

related to batteries that are listed in “USING THE UNIT SAFELY” and

“IMPORTANT NOTES” (supplied on a separate sheet).

5 When operating on battery power only, the unit’s indicator will

become dim when battery power gets too low. Replace the

battery as soon as possible.

5 Batteries should always be installed or replaced before connecting

any other devices. This way, you can prevent malfunction and

damage.

Main Specications

Nominal Input Level -20 dBu

Input Impedance 1 MΩ

Nominal Output

Level -20 dBu

Output Impedance 1 kΩ

Recommended Load

Impedance 10 kΩ or greater

Power Supply Carbon-zinc battery (9 V, 6F22) or

Alkaline battery (9 V, 6LR61)

AC adaptor (PSA series: sold separately)

Current Draw 15 mA

* Expected battery life under continuous use:

Carbon: 34.5 hours

Alkaline: 56 hours

These gures will vary depending on the

actual conditions of use.

Dimensions 73 (W) x 129 (D) x 59 (H) mm

2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches

Weight 370 g / 14 oz (including battery)

Accessories Leaet (“USING THE UNIT SAFELY,” “IMPORTANT

NOTES,” and “Information”)

Carbon-zinc battery (9 V, 6F22)

Options

(sold separately)

AC adaptor (PSA-series)

* 0 dBu = 0.775 Vrms

* This document explains the specications of the product at the

time that the document was issued. For the latest information,

refer to the Roland website.

Operating the Unit

1. When you have made the necessary

connections, set the knobs as

shown in the illustration.

2. Depress the pedal switch to turn the eect on. (The

CHECK indicator lights when the eect is on.)

3. Adjust the amount of overdrive

with the DRIVE knob.

4. Adjust the tone using the TONE

knob.

5. Adjust the level of the eect

sounds. Set the knob so there is

no volume dierence between the

eect and straight guitar sounds.

Changing the Battery

1. Hold down the pedal and loosen the thumbscrew, then

open the pedal upward.

* The pedal can be opened without detaching the thumbscrew

completely.

Thumbscrew

Battery Housing

Pedal

Spring Base

Coil Spring

Guide Bush

Hole

Battery Snap

Cord

Battery

Snap

9 V Battery

2. Remove the old battery from the battery housing, and

remove the snap cord connected to it.

3. Connect the snap cord to the new battery, and place

the battery inside the battery housing.

* Be sure to carefully observe the battery’s polarity (+ versus -).

4. Slip the coil spring onto the spring base on the back of

the pedal, and then close the pedal.

* Carefully avoid getting the snap cord caught in the pedal, coil

spring, and battery housing.

5. Finally, insert the thumbscrew into the guide bush

hole and fasten it securely.

Specyfikacje produktu

Marka:	Boss
Kategoria:	nieskategoryzowany
Model:	OD-3
Kolor produktu:	Black, Yellow
Typ produktu:	Pedał ekspresji
Rodzaj zasilania:	AC, Battery
Wysokość produktu:	59 mm
Szerokość produktu:	73 mm
Głębokość produktu:	129 mm
Waga produktu:	370 g
Gniazdko wyjścia DC:	Tak
Liczba baterii:	1
Zużycie energii:	15 mA
Impedancja wejściowa:	1000000 Ω
Impedencja wyjścia:	1000 Ω
Napięcie baterii:	9 V
Najlepsze zastosowania:	Gitara
6,35 mm (1/4 cala) wejście:	1
Ilość efektów dźwiękowych:	1
Nominalny poziom wejścia:	-20 dB
Wskaźnik LED statusu:	Tak