Instrukcja obsługi Bogen MAX1R

Bogen Konsola miksująca MAX1R

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Bogen MAX1R (2 stron) w kategorii Konsola miksująca. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

MAX1R

Mono Aux Input

Module

Features

• Gain/Trim control

• Bass and treble

• Audio Gating with threshold and duration adjustments

• Variable signal ducking when muted or gated

• Fade back from mute level

• 4 levels of available priority

• Can be muted from higher priority modules

• Can mute lower priority modules

54-2053-01C 0911

Specifications subject to change without notice.

www.bogen.com

Block Diagram

The Bogen MAX1R Mono Aux Input Module is warranted to be free from defects in material and workmanship for

three (3) years from the date of sale to the original purchaser. Any part of the product covered by this warranty that, with

normal installation and use, becomes defective (as confirmed by Bogen upon inspection) during the applicable warranty

period, will be repaired or replaced by Bogen, at Bogen’s option, provided the product is shipped insured and prepaid to:

Bogen Factory Service Department, 50 Spring Street, Ramsey, NJ 07446, USA. Repaired or replacement product will be

returned to you freight prepaid. This warranty does not extend to any of our products that have been subjected to abuse,

misuse, improper storage, neglect, accident, improper installation or have been modified or repaired or altered in any

manner whatsoever, or where the serial number or date code has been removed or defaced.

THE FOREGOING LIMITED WARRANTY IS BOGEN’S SOLE AND EXCLUSIVE WARRANTY AND THE PURCHAS-

ER’S SOLE AND EXCLUSIVE REMEDY. BOGEN MAKES NO OTHER WARRANTIES OF ANY KIND, EITHER

EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICU-

LAR PURPOSE ARE HEREBY DISCLAIMED AND EXCLUDED TO THE MAXIMUM EXTENT ALLOWABLE BY LAW.

Bogen's liability arising out of the manufacture, sale or supplying of products or their use or disposition, whether based

upon warranty, contract, tort or otherwise, shall be limited to the price of the product. IN NO EVENT SHALL BOGEN BE

LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOSS

OF PROFITS, LOSS OF DATA OR LOSS OF USE DAMAGES) ARISING OUT OF THE MANUFACTURE, SALE OR

SUPPLYING OF PRODUCTS, EVEN IF BOGEN HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES

OR LOSSES. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other

rights which vary from State to State.

Products that are out of warranty will also be repaired by the Bogen Factory Service Department – same address as

above or call 201-934-8500. The parts and labor involved in these repairs are warranted for 90 days when repaired by

the Bogen Factory Service Department. All shipping charges in addition to parts and labor charges will be at the owner's

expense. All returns require a Return Authorization number. For most efficient warranty or repair service, please include

a description of the failure.

12/2008

Gain

Provides control over the level of input signal that can be applied to

the internal signal buses of the main unit. Allows a way to balance

the input levels of various devices so that the main unit controls can

be set to relatively uniform or optimum levels.

Bass & Treble (Treb & Bass)

Provides separate control of Bass and Treble cut and boost. The Bass

control affects frequencies below 100 Hz and Treble affects frequencies

above 8 kHz. Clockwise rotation provides boost; counterclockwise rota-

tion provides cut. Center position provides no affect.

Gate - Threshold (Thresh)

Controls the minimum necessary input signal level to turn on the

moduleʼs output and apply mute signal to the main unit's buses.

Clockwise rotation increases the necessary signal level required to

produce output and mute lower priority modules.

Gate - Duration (Dur)

Controls the amount of time the output and mute signal of the module

remains applied to the main unitʼs buses after the input signal falls

below the required minimum signal level (set by the threshold control).

Ducking (Duck)

Controls the level of the output signal from the module when it has

been requested to mute/gate itsʼ output. The range is adjustable from

no reduction in level to full muting of the output signal.

Connections

Uses a standard RCA connector to make connections to the moduleʼs

input. The inputs are quasi-balanced to reduce the chance of ground

loops while still being compatible with unbalanced signal sources.

Module Installation

1. Turn off all power to the unit.

2. Make all necessary jumper selections.

3. Position module in front of desired module bay

opening, making sure that the module is right-

side up.

4. Slide module on to card guide rails. Make sure

that both the top and bottom guides are

engaged.

5. Push the module in to the bay until the face-

plate contacts the unitʼs chassis.

6. Use the two screws included to secure the

module to the unit.

WARNING:

Turn off power to unit and make all jumper

selections before installing module in unit.

Jumper Selections

Priority Level*

This module can respond to 4 different levels of

priority. Priority 1 is the highest priority. It mutes

modules with lower priorities and is never muted.

Priority 2 can be muted by Priority 1 modules

and mutes modules set for 3 or 4. Priority 3 is

muted by either Priority 1 or 2 modules and

mutes Priority 4 modules. Priority 4 modules are

muted by all higher priority modules.

The number of priority levels available is determined

by the amplifier the modules are used in.

Bus Assignment

This module can be set to operate so that the

mono signal can be sent to the main unitʼs A bus,

B bus, or both buses.

Gating

Gating (turning off) of the module's output when

insufficient audio is present at the input can be

disabled. Detection of audio for the purpose of

muting lower priority modules is always active

regardless of this jumper setting.

Specyfikacje produktu

Marka:	Bogen
Kategoria:	Konsola miksująca
Model:	MAX1R

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Bogen MAX1R, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Konsola miksująca Bogen

Bogen BAL2S Instrukcja

1 Marca 2025

Bogen CAM8Pro Instrukcja

1 Marca 2025

Bogen MIC2S Instrukcja

1 Marca 2025

Bogen MIC2X Instrukcja

1 Marca 2025

Bogen MAX1R Instrukcja

1 Marca 2025

Bogen LMR1S Instrukcja

1 Marca 2025

Bogen LMM1S Instrukcja

1 Marca 2025

Bogen TEL1S Instrukcja

1 Marca 2025

Bogen V100 Instrukcja

29 Września 2024

Bogen V150 Instrukcja

14 Września 2024

Instrukcje Konsola miksująca

Najnowsze instrukcje dla Konsola miksująca

Omnitronic PM-202FX Instrukcja

5 Marca 2025

Hobart MG1532 Instrukcja

27 Lutego 2025

American Audio Q-D6 Instrukcja

15 Stycznia 2025

ADB ME1163 Instrukcja

15 Stycznia 2025

Samson L1200 Instrukcja

14 Stycznia 2025

Samson MDR624 Instrukcja

14 Stycznia 2025

Konig KN-DIGICON20 Instrukcja

11 Stycznia 2025

Vonyx STM500BT Instrukcja

11 Stycznia 2025

Rane Sixty-Four Instrukcja

11 Stycznia 2025

Wharfedale SL 1224 USB Instrukcja

11 Stycznia 2025