Instrukcja obsługi Blaupunkt KPT-S1

Blaupunkt kamera bezpieczeństwa KPT-S1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Blaupunkt KPT-S1 (3 stron) w kategorii kamera bezpieczeństwa. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/3

Wireless Remote Keypad with Proximity Tags (KPT-S1)

1. Active LED (Blue/Orange)

2. Status LED (Blue/Red)

3. Fault LED (Orange)

4. Away Arm Key

5. Home Arm Switch

6. Status Key

7. Disarm Key

8. Panic Alarm

Press both 1 and 3 key to trigger Panic alarm

9. Fire Alarm

Press both 4 and 6 key to trigger Fire alarm

10. Emergency Alarm

Press both 7 and 9 key to trigger Emergency alarm

11. Battery Insulator

12. Mounting Knockouts

13. Tamper Switch

The Tamper switch protects the from unauthorized cover PIR

opening.

14. RFID TAG

1 x Remote Keypad

2 x wall plugs and screws

2 x RFID Tags

1 lithium batteries -installed) x 3V (pre

For learning the Remote Keypad:

1. Put the Control Panel into learning mode.

2. and Press both # 



 keys to transmit learn code

3. Refer to Control Manual to complete the learning process.

The Remote Keypad has 2 knockouts on the back where plastic

is thinner for wall mounting.

1. Use the two knockouts on the back to mark position on the

wall at chest height. Open the back cover.

2. Drill holes into the wall using the knockouts as template.

3. Fix the keypad base onto the wall with the screw and plugs

provided.

4. Replace the keypad cover onto the base.

The Remote Keypad features a power saving feature. When no

key is pressed for 5 seconds, the Remote Keypad will turn off

automatically to conserve power. When any key is pressed, the

Remote Keypad will wake up and turn on Active LED to indicate it

is now under normal operation

The Remote Keypad features a Test (programming) mode for you

to customize its setting. Before you start using the Remote

Keypad, you should first finish configuration setting.

The Remote Keypad also feature a Keypad PIN code which is

used to access the Test mode, To enter Test Mode, Enter

“ ”0000 (Default Keypad PIN code) key, the Active Orange + “ ”＊

LED will light up

Under Test Mode, the following functions include:

Key

Function

“ ” + “ ”＊1

Tag Management

“ ” + “7” ＊

Transmit learn code (same as pressing

both keys under normal mode) #and 





“ ” + “2” ＊

Enable dual key Panic Alarm function

“ ” + “3” ＊

Enable dual key Fire Alarm function

Surface Fixing

Knockouts x 2

“ ” + “4” ＊

Enable dual key Medical Alarm function

“ ” + “ ”＊5

Disable all dual key functions

“ ” + “6”＊

Change Keypad PIN Code:

1. Enter old code + “Status” Key

2. Enter new 4-digit code + “#” key

“ ” + “8”＊

Enable Arming without Use PIN code

function

“ ” + “9”＊

Enable Arm with User PIN code function

( ) Default

“ ” + “0”＊

Enable Arming with KP PIN code

function

“Disarm” twice

To leave Test Mode

RRFFIIDD TTAAGG MMaannaaggeemmeenntt

The Keypad can function with the RFID tags included in the

package. By assigning User PIN Code to a Tag, you can use the

Tag to Arm/Home/Disarm the Control Panel with a simple swipe.

Up to 6 tags can be stored in the Keypad and assigned to User

PIN Codes for panel control:

Add New Tag:

1. Enter Keypad Test Mode.

2. Enter 1 for Tag Management. Red Status LED will light up. “ ”＊+“ ”

3. Enter a 4-digit Control Panel User PIN Code key. “ ” + “ ”#

Status RED LED

flashes

Success

Status Blue LED

flashes with 4 beeps

Error: Wrong PIN Code length

Status Red LED

flashes with 4 beep

Error: Keypad already stored 6 Tags

4. Put the TAG close to the Keypad when Status Red LED is

flashing .

Status RED LED On

with 2 beeps

Success

Status Red LED On

with 1 bee

Same PIN Code already assigned to

this Tag

Status Red LED On

with 4 beeps

Error: Tag already assigned to another

User PIN Code

5. After finish adding new Tag, press Disarm key to exit Tag “ ”

Management.

Remove Existing Tag:

1. Enter Keypad Test Mode.

2. Enter 1 for Tag Management. Red Status LED will light “ ”+“＊”

up.

3. Enter the User PIN Code of the Tag you want to remove, then

press the Status key.

4. The Keypad will emit a long beep, the Tag info is removed.

If Remote Keypad is set to “Arm with Use PIN code ( ” “ ” + “9”＊

under Test Mode)

Away Arm

1. Enter a Control Panel User PIN Code +

“ ”Arm Key.

2. Press Arm Key + put Tag on Keypad. “ ”

Home Arm

1. Enter a Control Panel User PIN Code +

“ ”Home Key.

2. Press Home Key + put Tag on Keypad. “ ”

Disarm

1. Enter a Control Panel User PIN Code +

“ ”Disarm Key.

2. Press Disarm Key + put Tag on Keypad. “ ”

If Remote Keypad is set to Arm without Use PIN code ( 8“ ” “ ” + “＊”

under Test Mode)

Away Arm

Press Arm Key “ ”

Home Arm

Press Home Key “ ”

Disarm

Enter a Control Panel User PIN Code +

“ ”Disarm Key

If Remote Keypad is set to Arm with Keypad PIN code (“ ” “ ” + ＊

“ ”0 under Test Mode)

Away Arm

Enter Keypad PIN Code + Arm Key “ ”

Home Arm

Enter Keypad PIN Code + Home Key “ ”

Disarm

Enter Keypad PIN Code + Disarm Key “ ”

Press the Status key to inquire Control Panel status, the Status

LED will light up according to Control Panel mode

Red LED On

Away Arm mode

Red LED Flash

Home Arm mode

Blue LED on

Disarm mode

Dual Key Alarm function will activate alarm when both keys are

pressed at the same time. To use the functions, please enable

them under Test Mode. (Default are disabled)

“ ” “ ”1 + 3

Panic Alarm

“ ” “ ”4 + 6

Fire Alarm

“ ” “ ”7 + 9

Emergency Alarm



AAccttiivvee LLEEDD

The Active LED light up whenever any key is pressed.

Off

Keypad in Standby Mode

Blue LED On

Keypad in Normal Operation

Blue LED Flash

Keypad in Normal Operation and under

Low Battery

Orange LED On

Keypad in Test Mode

Orange LED Flash

Keypad in Test Mode and under Low

Batte ry



The Status LED light up during operation or when the Status key “ ”

is pressed to inquire Control Panel status

Red LED On

Away Arm mode

Red LED Flash

Home Arm mode

Blue LED On

Disarm mode

Blue LED Flash

No reply from Control Panel

Incorrect PIN code

Request for Home arm when under Away

arm mode

Request for Force Arm



The Fault LED light up whenever faults are detected in the alarm

system.

Orange LED On

Alarm in memory

Orange LED Off

Fault exists in system

BBaatttteerryy

The Remote Keypad uses 3 lithium battery as its power one V

source. It also features low battery detection function to notify the

Control Panel when battery voltage is low.

When the Remote Keypad is on low battery, follow the procedure

below to change the batteries.

1. Open the back cover

2. Remove the old batteries

3. Press any key several times to fully discharge.

4. Insert the new batteries observing correct polarity.

5. Replace the back cover.

FFaaccttoorryy RReesseett

If you forget your Keypad PIN code, or the Remote Keypad has

any problem, you can reset the Remote Keypad to factory

default.

1. Open the back cover and remove the battery

2. Press and hol 3 key and insert battery d “ ”

3. The Remote Keypad will sound 3 short beeps

4. Release 3 key, the reset process is now complete “ ”

- C to 40 C, relative humidity 85% non-condensing 10° ° .

868 MHz

Specyfikacje produktu

Marka:	Blaupunkt
Kategoria:	kamera bezpieczeństwa
Model:	KPT-S1
Kolor produktu:	Biały
Technologia łączności:	Bezprzewodowy
Ilość:	1
Zakres temperatur (eksploatacja):	-10 - 40 °C
Zakres wilgotności względnej:	0 - 85 %
Wymiary produktu (SxGxW):	80 x 116 x 20.5 mm
Odległość sensora:	200 m