Instrukcja obsługi BASSBOSS MFLA-MK3


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla BASSBOSS MFLA-MK3 (12 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/12
Dual 12”
Line Array
MFLA-MK3
User Manual
MFLA-MK3 Line Array User Manual
2
Table of Contents
Overview 2
SettingUptheMFLA-MK3LineArray 4
CorrectStackingProcedures 4
TheLinkage 5
SettingtheAngles 6
RiggingFrame 7
GroundSupport 9
ConnectingtheArray 11
QuickStartGuide 12
OutboardProcessorWarning 13
SetupProcedure 13
OperationandControls 14
IndicatorLEDs 14
HowtoUsethePresets 15
Pre-InstalledOnboardPresets 16
PowerDistribution 17
Troubleshooting 17
Specifications 18
Warranty 19
SafetyInformation 20
FCCComplianceNotice 21
The MFLA-MK3 is a dual 12” line array element featuring dual 3” voice coil, 1.4” throat compression drivers, a 3000W
amplifier and an integrated DSP. Low current draw and light weight relative to their output capacity means you can
provide intense sound with less power and fewer boxes.
Thecomprehensive processing ensures consistent, undistortedhigh-SPL operationand maximum reliability.All the
processingnecessary for linearfrequencyresponseand phasecoherentoperationare pre-programmedinto theDSP,
deliveringexceptionaldynamicresolutionanddetailalongwithprecisecontrol.
TheproprietaryprocessingprogrammedintotheBASSBOSSMFLA-MK3providetheeaseofplug-and-playoperation
andverysimpleandeasysetups.Youalsogetthepeaceofmindthatcomesfromknowingthattheintegratedlimiters
makethesystemcapableofoperatingreliablyatextremelyhighoutputlevels.
MFLA-MK3 Dual 12”
Line Array
Estemanualestádisponibleenespañolennuestrositiowebenbassboss.com/support
MFLA-MK3 Line Array User Manual
4
Setting up the MFLA-MK3 Line Array
Using the Rigging System
TheMFLA-MK3LineArrayhasrecessesononesideandslidersontheother.Theslidersare
locatedatthebottomofthecabinet.Therigginghardwareincludessingleextensionsatthe
bottomfrontanddoubleextensionsatthetopfront.
Therearetwoholesjustbehindandbelowthepivotpointofthecam.Theseholesline
upwithholesinthecamandareusedtolockthecamintospecificpositionsbeforethe
cabinetsareflownorsecured.
Bottom of Array Position
Thisistheupperholeandisusedonlyforthebottomcabinetinaflownarray.Itkeepsthe
camclearofthetuningports.Forcabinetsinotherpositions,thisholewillnotbeused.
Transport Position
Thispositionusesthelowerhole.Useittolockthecamabovethebottomofthecabinet
whenmovingitbyhand.Pushthehandledownuntilthecam’supperedgeiscenteredon
theportinthesideofthecabinet,theninsertthepinintothelowerholebehindthepivot.
Landing Position
Thispositionisalsoalignedwiththelowerhole.Itcorrespondstoa1-degreeangle,making
iteasytolandarraysontocartsoradditionalelementswithminimalsplay.Liftthehandle
nearthetopofthecabinetuntilanotherholeinthecamisexposed.Alignthisholewiththe
lowerholeandinsertthepintolockitinplace.
Correct Stacking Procedures
Theslidersandgrooveshelpyoulineupthecabinetsbeforethemetalpartstouch,making
thealignmentprocesseasierandsafer.Thistwo-stageprocesssupportstheweightand
guidesthepartsaccurately,reducingtheriskofdamagetothelinkageandyourfingers.
1. Setting Up the First Cabinet (Cab A)
-PlaceCabAinpositionandsecureit.Makesuretherearenopinsinitsupper-frontlinkages.


Specyfikacje produktu

Marka: BASSBOSS
Kategoria: Niesklasyfikowane
Model: MFLA-MK3

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z BASSBOSS MFLA-MK3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Niesklasyfikowane BASSBOSS

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

SmallRig

SmallRig VB99 SE Instrukcja

29 Stycznia 2025
QSC

QSC TSC-8 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025
Sunding

Sunding SD-581G Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025
XTRARM

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025
OSEE

OSEE TX402 Instrukcja

29 Stycznia 2025