Instrukcja obsługi BASSBOSS DJ18-MK3

BASSBOSS głośnik DJ18-MK3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla BASSBOSS DJ18-MK3 (16 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/16
User ManUal
Single 18”
Powered Subwoofer
DJ18S-MK3
DJ18-MK3 User Manual
2
Table of Contents
Overview 2
QuickStartGuide 4
OutboardProcessorWarning 5
SetupProcedure 5
OperationandControls 6
IndicatorLEDs 6
HowtoUsethePresets 7
Pre-InstalledOnboardPresets 8
PowerDistribution 9
Troubleshooting 9
CardioidMode 10
Specifications 11
Warranty 12
SafetyInformation 13
ImportantNotes 14
FCCComplianceNotice 14
Overview
The DJ18-MK3 is a premium-quality subwoofer which delivers deep bass at levels far higher than
would be expected from its size. Suitable for the truly bass-insatiable who focus on modern music with
frequencies well below the usual 50-100Hz range, this compact sub weighs only 110 lbs and delivers
output down to 27Hz (-3dB).
The DJ18-MK3 is a single 18-inch direct-radiating subwoofer featuring a long-excursion woofer loaded
into a vented enclosure that is optimally tuned to deliver flat frequency response to very low frequencies
with high sensitivity. The cabinet was designed to minimize mass and maximize eiciency. The point is
to do less heavy lifting and deliver more heavy bass.
Estemanualestádisponibleenespañolennuestrositiowebenbassboss.com/support
Single 18”
Powered Subwoofer
DJ18S-MK3
bassboss.com
3
The DJ18-MK3 features a 2500W amplifier with an auto-sensing, globally compatible power supply
that can run on mains supplies anywhere between 90 and 250 Volts. Full output power is available on
anything over 110V. The amplifier’s high peak-output voltage provides intense high SPL hits, while its
sustained output is unparalleled in its ability to deliver those “liquid” lows.
The amplifier is passively cooled via its external heat-sink and by woofer-generated air-flow through the
port. When necessary, two blower-fans are engaged to provide additional forced-air cooling capacity in
more extreme conditions.
New to the MK3 are Neutrik powerCON True 1 TOP (Total Outdoor Protection) waterproof mains
connectors. Waterproof mains connectors, along with a totally isolated input connection section and
cones that are waterproofed, make the MK3 series the powered loudspeakers that can be used outdoors
without fear of what the weather will bring, or used indoors without fear of what the partiers fling.
Electrical power is converted into the much more desirable acoustical power by a robust, neodymium
motor, 18-inch woofer with a massive 4.5-inch (115mm) copper-wound voice coil. Neodymium magnets
are lighter and their higher intensity provides higher eiciency, so the result is a lighter and louder cabinet
than those with ferrite drivers.
The MK3 features an all-new DSP. The comprehensive suite of processing includes high-pass and low-
pass filters as well as multiple protection systems and limiters to prevent driver overload in as many
ways as possible, including thermal, excursion and clipping. The five levels of protection actively prevent
overheating of the voice coil, minimize long-term thermal compression, and limit excursion. Because
they operate in 5 dierent modes, the limiters are sophisticated enough to have a largely unnoticable
eect on the transient response, and so allow the subwoofer to deliver peak output safely.
The new DSP features an Ethernet interface. This can be used to control the cabinets from a computer
or to load software or firmware updates. The ethernet connectivity, in conjunction with the new DSP
board, will allow signal to be sent via Milan AVB. (Firmware updates will provide access to this feature.)
Within the software, multiple cabinets can be grouped together, allowing them to respond to commands
simultaneously. This permits the levels of groups of loudspeakers to be adjusted together and yet
independently from the levels of other groups of loudspeakers. In addition to individual and grouped
level controls, presets can be loaded and signal levels and temperatures can be monitored. Each cabinet
includes a two-port switch, so multiple cabinets can be chained on the same data cable.
The MK3 DSP features storage capacity of up to 100 presets, eight of which can be accessed at the touch
of a button with no need for a connected computer. The eight directly accessible presets are compatible
with all the presets in the MK3 Top Boxes and are also compatible with previous generation tops and subs.

Specyfikacje produktu

Marka: BASSBOSS
Kategoria: głośnik
Model: DJ18-MK3

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z BASSBOSS DJ18-MK3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik BASSBOSS

BASSBOSS

BASSBOSS DJ18-MK3 Instrukcja

5 Października 2024
BASSBOSS

BASSBOSS SSP118-MK3 Instrukcja

5 Października 2024
BASSBOSS

BASSBOSS CCM12-MK3 Instrukcja

5 Października 2024
BASSBOSS

BASSBOSS AT212-MK3 Instrukcja

5 Października 2024
BASSBOSS

BASSBOSS BB15-MK3 Instrukcja

5 Października 2024
BASSBOSS

BASSBOSS KRAKEN-MK3 Instrukcja

4 Października 2024
BASSBOSS

BASSBOSS DiaMon-MK3 Instrukcja

4 Października 2024
BASSBOSS

BASSBOSS SSP218-MK3 Instrukcja

16 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024