Instrukcja obsługi Barska AE10748
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Barska AE10748 (4 stron) w kategorii teleskop. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/4
TELESCOPES
BARSKA® Optics, as manufacturer, warrants this new precision optical product to be
by this warranty. This warranty does not include damage caused by abuse, improper
handling, installation, maintenance, normal wear-and-tear, unauthorized repairs
purchaser and is not transferable.
This warranty applies only to products purchased in the United States of America and
Canada.
In the event of a defect within 30 days, the consumer must return the defective unit to
the BARSKA dealer (the place of purchase) at his/her own expense.
Beyond 30 days, BARSKA products should be sent to the following address for
warranty repairs. Products must be packed carefully and sturdily to prevent damage in
transit, and returned freight prepaid to:
BARSKA® OPTICS
855 Towne Center Drive
Pomona, CA 91767
For additional and updated information
please visit our website at www.barska.com
Please email info@barska.com or call 1.888.666.6769 for Return Merchandise
Number (RMA#) before any returns. NOTE: All merchandise received without a valid
RMA # will be returned to shipper at his/her own expense.
Please include all of the following when returning BARSKA products for service and/or
replacement:
1. Please write your complete details (Name, Address, Telephone #, E-mail address,
RMA#, etc.)
2. Purchase receipt or Proof of Purchase. (Original/Copy)
3. A brief explanation of the defect.
4. A Check/Money Order of $25.00 cover inspection, shipping and handling.
*Please allow 6-8 weeks for delivery.
This product will either be replaced or repaired at the discretion of the warrantor. If it’s
a discontinued item, we will replace the product with an equivalent product. Should
the repair not be covered by this warranty, an estimate will be sent for your approval.
Non-warranty repairs or refurbishing of your optical products are always provided at a
reasonable cost.
BARSKA® shall not be liable for any consequential, incidental and/or contingent
damages whatsoever. We will not pay shipping, insurance or transportation charges
from you to us, or any import fees, duties and or taxes. This warranty supersedes all
previous BARSKA warranties.
7/15© 2015 BARSKA®
1 YEAR LIMITED WARRANTY
7/15 BC432w w w . b a . c o ma r s k
Setup Instructions
Unpack and lay out all of the parts in a large, clear area where you will have
room to assemble the pieces.
1. Fully extend the legs of the tripod apart
2. On the head of the tripod is the Vertical Axis Screw and lock nut. Separate the
Vertical Axis Screw from the lock nut by holding the Vertical Axis Screw in
place and unscrewing the lock nut off the screw
3. Under the base of the telescope is the mounting platform. Align the head of the
tripod to the mounting platform so that the screw in the mounting platform lines
up with the holes of the mounting platform. Insert the Vertical Axis Screw
through the holes to attach the tripod to the telescope pieces together with
lock nut.
Initial set up is shown in the picture on the left. Should look like picture on the
right when nished.
4. Remove caps from telescope
Note: When mounting the parts ensure that the securing screws are not tightened
too tightly. Tightening too tightly could result in damage the parts or the internal
thread of the holders.
w w w . b a r s k a . c o m
2
450 Power, 60050 Starwatcher Telescope 450 Power, 60050 Starwatcher Telescope
3
w w w . b a r s k a . c o m
1. Tripod Brace with Leg
Adjustment Screw
2. Tripod Leg
3. Objective Lens
4. Telescope Main Body
5. Finder Scope
6. Finder Scope Bracket
7. Eyepiece
8. Diagonal
9. Focus Knob
10. Vertical Axis Screw
11. Horizontal Axis Screw
CAUTION: DO NOT LOOK DIRECTLY AT THE
SUN. VIEWING THE SUN OR ANY LIGHT
SOURCE WITH THIS OPTICAL DEVICE CAN
CAUSE PERMANENT EYE DAMAGE.
1
2
3
4
6
5
7
8 9
10
11
Attaching the Accessories
Finderscope
1. Remove caps from the eyepiece of the nderscope
2. Remove the two small, silver thumbscrews located at the back of the
telescope tube
3. Place the nderscope bracket over the two screws, lining up the holes on the
nderscope bracket with those of the screws
4. Replace the two small, silver thumbscrews back on to the screws to secure the
nderscope on to the telescope optical tube
Initial set up is shown in the picture on the left. Should look like picture on the
right when nished.
Diagonal
1. Remove the caps from the focus tube and the diagonal
2. Insert the chrome end of the diagonal into the focuser and lock into place by
tightening the thumb screws on the focus tube
Eyepiece
1. Select an eyepiece, place it into the diagonal. Lock the eyepiece it into place
with the thumb screw.
Barlow Lens
The included 3x Barlow lens triples the magnifying power of each eyepiece.
See Barlow Lens page 6
Diagonal and Eyepiece Initial set up is shown in the picture on the left. Should
look like picture on the right when nished.
How to Use Telescope:
First try out your telescope in the daytime and learn to use the telescope looking
at easily identiable objects. Get familiar with the telescope’s movements,
pointing, focusing, different eyepieces, and magnifying powers. Below is some
information on how to use the telescope.
Telescope Movement:
In order to move the telescope
horizontally (left to right)
- Loosen Horizontal Axis Screw
In order to move the telescope
vertically (up and down)
- Loosen Vertical Axis Screw
Adjusting the Finder Scope:
Since the telescope has a limited eld
of view, it can be quite difcult to locate
a given star or planet. For this reason the telescope is tted with a nder scope
with reticule for orientation. It is advisable to complete the following settings in
daylight.
1. Insert the eyepiece with the lowest magnication in the Zenith mirror
or Zenith prism. Look at a stationary easily recognizable object that
is not further away than 300m. Turn the telescope with the horizontal
axle, and move the vertical axle until the object is in the middle of the
eld of view, and then focus the image. Tighten the adjusting screw
on the mount so that the telescope remains in this position (the higher
the object is above the horizon, the easier it is to locate).
w w w . b a r s k a . c o m
4 5
w w w . b a r s k a . c o m
450 Power, 60050 Starwatcher Telescope 450 Power, 60050 Starwatcher Telescope
Specyfikacje produktu
| Marka: | Barska |
| Kategoria: | teleskop |
| Model: | AE10748 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Barska AE10748, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje teleskop Barska
26 Września 2024
26 Września 2024
26 Września 2024
26 Września 2024
26 Września 2024
26 Września 2024
Instrukcje teleskop
- teleskop Marquant
- teleskop IOptron
- teleskop National Geographic
- teleskop Carson
- teleskop Bresser
- teleskop Orion
- teleskop Levenhuk
- teleskop Sky-Watcher
- teleskop GlobalTronics
- teleskop Celestron
- teleskop Konig
- teleskop Meade
- teleskop Vixen
- teleskop Discovery
- teleskop Danubia
- teleskop ZWO
- teleskop SVBONY
- teleskop DayStar Filters
- teleskop Mizar
Najnowsze instrukcje dla teleskop
8 Października 2024
4 Października 2024
4 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
2 Października 2024
1 Października 2024
1 Października 2024
29 Września 2024