Instrukcja obsługi Audiovox PRO-9056TW Pursuit Series

Audiovox Bezpieczeństwo PRO-9056TW Pursuit Series

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Audiovox PRO-9056TW Pursuit Series (2 stron) w kategorii Bezpieczeństwo. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

128-8856

1 of 2

Single Channel Remote

Car Starter

Model PRO-9056TW

Owner’s Manual

FEATURES :

 1 Programmable RF Transmitters, 1 Programmable RF Transceiver

 Single Channel Receiver (capable of accepting 4 transmitters)

 External Superheterodyne Receiver Antenna w/PushButton Switch &

Orange LED

 On-Board Start Relay

 On-Board Accessory Relay

 On-Board Ignition 1 Relay

 On-Board Ignition 2 Relay

 Ignition 2 Relay Selectable On or Off During Cranking

 On-Board Parking Light Relay

 Ignition 3 / Shock By-Pass / GM VAT Output (relay required)

 Tach Signal Learning Circuit

 Two ( + ) and Two ( - ) Safety Shutdown Circuits

 Alarm By-Pass Output

 Accessory Outputs

(Pulse Before & After Start, During Crank & After Shut Down)

 Selectable Steady or Flashing Parking Lights for Run Indication

 Selectable 5, 10, 15, 20 Minute Run Time

Optional Door Unlock Feature For Vehicles Equipped With Power Doors

(Only operational while running under control of the remote start unit.)

128-8856

2 of 2

REMOTE STARTING THE VEHICLE

This will not start the vehicle if any one of the following situations exists:

The vehicle's hood lid is opened.

The gear shift selector is not in Park.

The brake pedal is depressed.

The safety control switch is in the Off position.

1) To start the vehicle, press and release the transmitter button two times within

2 seconds. The vehicle will start and remain running for the

pre-programmed time up to a 60 minute run cycle. As a

visual indication, the parking lights will flash or remain on

depending on the setting by your installation center. Addi-

tionally if the two way transceiver shown on the right is used,

the transceiver will play a melody when the vehicle is started,

and the Orange LED surrounding the transceiver button will

flash every ten seconds while the vehicle is running.

2) When you arrive at the vehicle, turn the ignition key to the

ON position (not the spring loaded start position), then step

on the brake pedal to disengage the remote starter. The

vehicle will continue to run, but now on its own power.

NOTE: The engine will stop running before the pre-programmed

run cycle has expired if you perform any one of the following

functions:

-Press the button on the keychain transmitter two times within 2 seconds

-Depress the brake pedal

-Open the vehicle's hood

-Move the safety control switch to the Off position.

PUSH-BUTTON LED RECEIVER VALET/OVERRIDE/SAFETY CONTROL SWITCH

The Push-Button LED switch located in the receiver allows you to temporarily disable the remote

starting function of the system. This recommended whenever the vehicle is being serviced. To place

the system in the service mode:

1) With the system disarmed/unlocked, and the ignition switch off, Press and Hold the Push-Button

switch found on the windshield receiver, in.

2) Turn the ignition switch on, off, on, off, on, off.

3) The Orange LED begins to flash two short flashes followed by one long flash and continues this

pattern until the unit is returned to the normal mode of operation.

The above action puts the unit into the Remote Start Override/Service mode and will not start from

the RF transmittor or any other input, Posse or otherwise.

To Exit Remote Start Override Mode

1) With the system disarmed, Press and Hold the Push-Button switch found on the windshield

receiver, in.

2) Turn the ignition switch on, off, on, off, on, off.

3) The LED turns off indicating that the Remote Start unit is fully functional once again.

UNLOCKING THE VEHICLE:

If you have electric door lock, and the Optional Unlock feature was added, with the vehicle running

under command of the remote start unit, press and hold the transmitter button for 3 seconds until

the doors unlock.

TELEMATIC UPGRADE:

This system has the ability to have a telematic upgrade module connected to it. This is an upgrade that

can give you control of certain functions of your vehicle from a Telephone, or in some cases a

computer interface. Please check with your installation center for most recent Telematic Upgrades. If

you had a Telematic Upgrade installed, the manual supplied with the upgrade unit will provide a

operator's manual advising of the features of the system and means available to control these

features of your vehicle.

.FUNCTION SETTING CHART To be completed by installer

Run Time 5 Min 10 Min 15 Min 20 Min 

Lights Pulse Steady 

Specyfikacje produktu

Marka:	Audiovox
Kategoria:	Bezpieczeństwo
Model:	PRO-9056TW Pursuit Series

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Audiovox PRO-9056TW Pursuit Series, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Bezpieczeństwo Audiovox

Audiovox AS9233ST Instrukcja

24 Września 2024

Audiovox Prestige Platinum APS 686T Instrukcja

23 Września 2024

Audiovox APS-45 Instrukcja

23 Września 2024

Audiovox PRO-9056TW Pursuit Series Instrukcja

23 Września 2024

Audiovox APS 675 Prestige Platinum Instrukcja

23 Września 2024

Instrukcje Bezpieczeństwo

Najnowsze instrukcje dla Bezpieczeństwo

NetworX NX-595E IP Communication Module Instrukcja

5 Października 2024

Geemarc SOS-PRO 295 Instrukcja

2 Października 2024

One2track Safety Angel Instrukcja

28 Września 2024

Sygonix SY-3851632 Instrukcja

28 Września 2024

Sygonix 1326052 Instrukcja

28 Września 2024

Sygonix 43588A WLAN Camera Instrukcja

28 Września 2024

Sygonix 43176S LAN Camera Instrukcja

28 Września 2024

Sygonix SY-3181234 Instrukcja

28 Września 2024

Sygonix Touch IP65 Instrukcja

28 Września 2024

Sygonix 1882082 Instrukcja

28 Września 2024