Instrukcja obsługi ATen CV100KM

ATen Kable do komputerów PC i urządzeń peryferyjnych CV100KM

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla ATen CV100KM (2 stron) w kategorii Kable do komputerów PC i urządzeń peryferyjnych. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Overview

The CV-100KM is a PS/2 keyboard and mouse emulator

designed to provide a simple, inexpensive solution to common

problems associeated with KVM (keyboard, video, mouse),

switches. It permanently cures damaging computer lock-up

commonly found in those KVM switches that do not provide

keyboard and mouse emulation. With those switches, the

computers ’lose’ the keyboard and/or mouse when the focus

switches to a different system.

Simply plug the emulator into the computer’s keyboard and

mouse ports, and the CV-100KM’s state-of-the-art

microprocessor appears to the system as if there were an actual

keyboard and mouse present. The computer boots and operates

normally, with or without the presence of a real keyboard and

mouse.

Because the CV-100KM’s circuitry allows seamless and fail-safe

hot plugging of the keyboard and mouse, you can hot swap the

two peripherals among any number of computers at any time.

The emulator works with just the keyboard or just the mouse

present, as well.

Features

MPrevents comptuer lockup due to keyboard signal loss with

KVM switches

MAllows hot plugging of the keyboard and mouse

MAllow keyboardless/mouseless boot and run - for increased

security

MNon-powered - uses the computer’s keyboard power source

MFor KVM devices that do not provide keyboard and mouse

emulation

System Requirements

PS/2 Keyboard and Mouse ports installed on your

computer or KVM switch.

Top View

1. Mouse and Keyboard Ports

The cables from your PS/ 2 Mouse and PS/ 2 Keyboard plug

in here. Each port is marked with an appropriate icon to

indicate which one it is.

Note: If you are using a KVM switch, the keyboard and

mouse connectors from the KVM cable plug in here.

2. Mouse and Keyboard LEDs

The LEDs light to show that the peripheral has connected to

the computer. The corresponding LED flashes when the

keyboard or mouse transmits data.

3. Mouse and Keyboard Connectors

These connectors plug into the keyboard and mouse ports of

your computer. Each connector is marked with an appropriate

icon to indicate which one it is.

Bottom View

1. Wake Up Switch

MIf your keyboard has Wake Up capability, you can bring

the computer back from power saving mode, by pressing

its Wake Up key, or by tapping the Right Shift key.

MIf your keyboard does not have Wake Up capability, press-

ing this Wake Up switch brings the computer back from

power saving mode.

NOTE: This equipment has been tested and found to comply

with the limits for a Class B digital device pursuant to Subpart

J of Part 15 of FCC Rules. These limits are designed to

provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more

of the following measures:

MReorient or relocate the receiving antenna.

MIncrease the separation between the equipment and re-

ceiver.

MConnect the equipment into an outlet on a circuit different

from that which the receiver is connected.

MConsult the dealer or an experienced radio/television tech-

nician for help.

- 2 -- 1 - - 3 -

Installation

Installation simply entails plugging the cables into their

appropriate sockets as shown in the diagrams below:

Troubleshooting

Problem Cause Action

Erratic Operation Static electricity may

cause the unit to

operate erratically.

Unplug the CV-100KM’s

cables from the computer’s

keyboard and mouse ports,

then reinsert them.

Specifications

Function Specification

Connectors Keyboard 1 x 6 pin mini-din F (to keyboard)

1 x 6 pin mini-din M (to computer)

Mouse 1 x 6 pin mini-din F (to keyboard)

1 x 6 pin mini-din M (to computer)

LEDs 2

Switches 1 x Remote wakeup pushbutton

Cable Length 30 cm

Operating Temperature 0 ~ 50o C

Storage Temperature -20 ~ 60o C

Humidity 0 ~ 80% RH

Housing Plastic

Limited Warranty

IN NO EVENT SHALL THE DIRECT VENDOR’S LIABILITY

EXCEED THE PRICE PAID FOR THE PRODUCT FROM

DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES RESULTING FROM THE USE

OF THE PRODUCT, DISK, OR ITS DOCUMENTATION.

The direct vendor makes no warranty or representation,

expressed, implied, or statutory with respect to the contents or

use of this documentation, and especially disclaims its quality,

performance, merchantability, or fitness for any particular

purpose.

The direct vendor also reserves the right to revise or update the

device or documentation without obligation to notify any

individual or entity of such revisions, or update. For further

inquiries, please contact your direct vendor.

- 4 - - 5 -

User Manual

CV-100KM

Read this manual thoroughly and follow the installation and

operation procedures carefully to prevent any damage to the

unit, and/or any of the devices connected to it.

This package contains:

M1 CV-100KM PS/2 Keyboard-Mouse Emulator

M1 User Manual

If anything is damaged or missing, contact your dealer.

Manual Part No. PAPE-1227-1AT

Printed in Taiwan 01/2003

All brand names and trademarks are the registered property of their respective owners.

Specyfikacje produktu

Marka:	ATen
Kategoria:	Kable do komputerów PC i urządzeń peryferyjnych
Model:	CV100KM

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z ATen CV100KM, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Kable do komputerów PC i urządzeń peryferyjnych ATen

ATen CV190 Instrukcja

22 Września 2024

ATen SXP325A Instrukcja

22 Września 2024

ATen CS62KM Instrukcja

22 Września 2024

ATen CV211CP Instrukcja

21 Września 2024

ATen ACS-62 Instrukcja

20 Września 2024

ATen CV211 Instrukcja

18 Września 2024

ATen UC485 Instrukcja

18 Września 2024

ATen CV100KM Instrukcja

18 Września 2024

ATen UE250 Instrukcja

18 Września 2024

ATen UC1284B Instrukcja

17 Września 2024

Instrukcje Kable do komputerów PC i urządzeń peryferyjnych

Najnowsze instrukcje dla Kable do komputerów PC i urządzeń peryferyjnych

Goobay 68874 Instrukcja

9 Października 2024

Goobay 61259 Instrukcja

9 Października 2024

Kogan KAHBCSPLT4A Instrukcja

9 Października 2024

Laserliner PersonalCable Instrukcja

9 Października 2024

StarTech.com USBAUB1MBK Instrukcja

9 Października 2024

StarTech.com USBAUB3MBK Instrukcja

9 Października 2024

StarTech.com USBAUB2MBK Instrukcja

9 Października 2024

StarTech.com CRJ4550PK Instrukcja

9 Października 2024

StarTech.com CRJ45C6STR50 Instrukcja

9 Października 2024

StarTech.com ST8CU824 Instrukcja

9 Października 2024