Instrukcja obsługi Atdec TH-30-50-RW

Atdec Wsparcie dla płaskich paneli TH-30-50-RW

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Atdec TH-30-50-RW (2 stron) w kategorii Wsparcie dla płaskich paneli. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Component Checklist
Bits Box Mounting
Screws
Installation Instructions
TELEHOOK
30”-50” UNIVERSAL ROTATING WALL MOUNT
Attaching the Display to the Wall Plate
C
Mounting the Wall Plate
A
Masonry Wall Timber Stud Wall
Adjusting the Pivot Head to suit the weight of the
Display
The Pivot head is factory set to hold
approximately 35kgs (77lbs). If the display is not
holding its position when placed on the wall it
may be necessary to remove the display from
the wall and tighten the M12 Hex Nut on the
back of the Pivot Head using a 17mm (
11/16”)
socket wrench or shifter. To achieve a one-touch
effortless adjustment setting it is advised that the
nut be tightened at half turns and re-tested, until
the desired friction is achieved. Alternatively the
M12 Hex Nut can be over tightened in order to
lock the display in position.
Bracket (x2)
Pivot Head
Extension Plate
Wall Plate
Bracket Plate (x2)
Coach
Screw (x4)
Masonry Wall
Plug (x4)
Large
Washer (x4)
Multi
Washer (x4)
Spacer
Bush (x4)
M6x16mm Socket
Drive Screw (x12)
M8x20mm
Phillips Head
Screw (x4)
M6x16mm
Phillips Head
Screw (x6)
M5x16mm
Phillips Head
Screw (x6)
Allen Key
Small
Washer (x4)
Large Washer
Masonry
Wall Plug
Wall Plate
12mm (1/2
”)
Hole
TIP: Use a spirit
level to ensure the
wall plate is
horizontal
Note: Ensure the Wall Plate
is mounted with the narrow
end of the Mounting Slot
at the bottom.
Coach Screw
Note: Ensure the Wall Plate is
mounted with the narrow end of the
Mounting Slot at the bottom.
Large
Washer
Coach Screw
8mm (5/16 ”)
Hole
Timb er
Stud
With the mount attached to the display, lift the
display and slide the Back Plate into the Mounting
slots to ensure a secure connection.
Tighten
M12 Hex Nut
Security Option
D
For additional security,
it is suggested that a
Padlock be attached to
the Back plate as shown.
The Padlock (not supplied)
should have a shackle
diameter no larger than
4mm (3/16”).
Padlock
Note: This procedure will require two persons
Back Plate
Mounting
Slots
Mounting Slot
Note: For demonstration purposes, the display
has been omitted from the image below.
Back plate
Shackle 4mm (3/16”)
diameter or less
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 18.04.07 ©
Important Notes
TOOLS REQUIRED:
Power Drill
12mm or 8mm Drill Bit
Phillips Head Screw Driver
Spirit Level
17mm (11/16”) Socket Wrench
or Shifter
The Telehook 30-50 Universal Rotating Wall Mount supports flat panel displays from 30” (76cm) to 50” (127cm)
and supports a maximum load of 85kgs (187lbs).
This product is factory set to support 35kgs (77lbs), and will need to be adjusted if the display is heavier or lighter.
The manufacturer does not accept responsibility for incorrect installation.
TIP: Use a spirit
level to ensure the
wall plate is
horizontal
C.1. Attaching the Display to the Wall Plate C.2. Pivot Head Load Capacity Adjustment
M4x16mm
Phillips Head
Screw (x6)
Centre Holes
Note: It is recommended to
mount the Wall Plate by firmly
fixing the four Coach Screws
into two studs. However, if the
weight of the display is less than
50kgs (110lbs), it is possible to
mount the Wall Plate to one stud
by fixing the two Coach Screws
through the two Centre holes.
Note: For demonstration purposes, the wall
has been omitted from the above image.
Configuration 3: 260mm to 660mm (101/4”-26”) x 200mm to 400mm (8”-15 3/4”)
Mounting Hole Patterns
Choosing and Assembling the Correct Mounting Configuration
B
Measure the mounting hole pattern on the back of the display. Select the appropriate configuration (either 1, 2
or 3) that best suits the mounting hole pattern of the display then attach the product to the display as shown.
ii
Mounting Screw
Pivot Head
Back
of Display
Note: The
100mmx200mm
mounting
configuration is
shown. For mounting
displays with
100mmx100mm
mounting hole
patterns, use the
100mmx100mm holes
in the Pivot Head.
Bracket
Plate
Pivot Head
Back
of Display
Bracket
M6 Socket
Drive Screw
Mounting
Screw
Multi Washer
100mm
(4”)
100mm
(4”)
200mm (8”)
260mm
(101/4”)
660mm (26”)
400mm
(153/4”)
200mm
(8”)
Spacer Bush Assembly
If the mounting holes are recessed into the
back of the display, use the supplied Spacer
Bushes to pack the recessed hole and ensure
that the bracket is securely fixed to the display.
Note: If the display has a vertical
mounting distance of 200mm and
requires the use of the M6 Mounting
Screws, it will be necessary to
substitute the MuIti Washers for the
small washers provided.
Pivot Head M6 Socket
Drive Screw
Bracket
Plate Mounting
Screw
Multi Washer
Extension
Plate
Multi Washer
Mounting Screw
Bracket
Recessed Hole
Spacer Bush
Small
Washer
M6 Mounting
Screw
Back
of Display
Configuration 1: VESA Compliant 100mmx100mm (4”x4”) & 100mmx200mm (4”x8”)
Mounting Hole Patterns
Configuration 2: 200mmx200mm to 400mm (8”x8”-15 3/4”) Mounting Hole Patterns
200mm
(8”)
200mm
(8”)
400mm
(153/4”)
Attaching the Bracket to the Display
Note: When assembling the product,
ensure the red Telehook Badges are
positioned towards the bottom of the display
In order to ensure the display is securely attached to the
bracket it is recommended that the bracket be fastened with the
mounting screws aligned along the bottom edge of the slots.
It is also important that you use the supplied Multi Washer and
ensure that the tightest fitting hole in the washer is used for the
specific size screw
M6 Screw
Hole
M8 Screw
Hole
M4 & M5
Screw Hole
Multi Washer
Slot
Telehook
Badge
Note: When assembling the
product, ensure the Telehook
Badges are positioned towards the
bottom of the display
Telehook
Badge
100mm
(4”)
Spacer Bush
Top of
Display
Top of
Display
Top of
Display

Specyfikacje produktu

Marka: Atdec
Kategoria: Wsparcie dla płaskich paneli
Model: TH-30-50-RW

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Atdec TH-30-50-RW, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Wsparcie dla płaskich paneli Atdec

Atdec

Atdec AWMS-DW6-S Instrukcja

7 Grudnia 2024
Atdec

Atdec AWM-W-S Instrukcja

7 Grudnia 2024
Atdec

Atdec AWMS-46W35-S Instrukcja

7 Grudnia 2024
Atdec

Atdec AWMS-HX40-H-B Instrukcja

7 Grudnia 2024
Atdec

Atdec AD-WF-8060 Instrukcja

7 Grudnia 2024
Atdec

Atdec AD-WT-8060 Instrukcja

7 Grudnia 2024
Atdec

Atdec AD-WF-10090 Instrukcja

7 Grudnia 2024
Atdec

Atdec AWM-W-B Instrukcja

7 Grudnia 2024
Atdec

Atdec AD-WFP-5040 Instrukcja

7 Grudnia 2024
Atdec

Atdec TH-1030-VFM Instrukcja

22 Września 2024

Instrukcje Wsparcie dla płaskich paneli

Najnowsze instrukcje dla Wsparcie dla płaskich paneli

Adicam

Adicam MAX+ Film Cart Instrukcja

29 Stycznia 2025
Adicam

Adicam STANDARD Film Cart Instrukcja

29 Stycznia 2025
Adicam

Adicam MINI Film Cart Instrukcja

29 Stycznia 2025
B-tech

B-tech BT9340-FM Instrukcja

15 Stycznia 2025
StarTech.com

StarTech.com ARMPIVOTE2 Instrukcja

15 Stycznia 2025
StarTech.com

StarTech.com 3M1A3SG-MONITOR-ARM Instrukcja

15 Stycznia 2025
Vogel's

Vogel's FM1622 Instrukcja

15 Stycznia 2025
NeoMounts

NeoMounts DS45-430BL16 Instrukcja

14 Stycznia 2025
NeoMounts

NeoMounts DS42-430BL14 Instrukcja

14 Stycznia 2025
NeoMounts

NeoMounts NS-WMB300PBLACK Instrukcja

14 Stycznia 2025