Instrukcja obsługi Atdec AD-WF-10090

Atdec Wsparcie dla płaskich paneli AD-WF-10090

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Atdec AD-WF-10090 (2 stron) w kategorii Wsparcie dla płaskich paneli. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

AD-WF-10090 Page 1 of 2

Wall Plate

Display Bracket (x2)

M-G

Short

Spacer

(x8)

M-H

Long

Spacer

(x8)

M-F

Multi

Washer

(x4)

M-D

M8x30

Screw

(x4)

M-B

M6x14

Screw

(x4)

M-A

M5x14

Screw

(x4)

M-C

M6x30

Screw

(x4)

M-E

M8x50

Screw

(x4)

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! The manufacturer accepts no responsibility for incorrect installation.

! Failure to mount this product correctly may cause serious injury/death during or following installation.

! This product is not suitable for outdoor use.

! Do not use this product for mobile applications.

! Wall Plate only achieves maximum weight rating when appropriately fastened to a wall of adequate structural capacity.

! Professional installer to ensure adequate structural capacity of wall (including appropriate safety factor) to support total

weight of all equipment being mounted.

! Drilling into electrical wires can cause death - use appropriate equipment and caution when drilling holes in walls to avoid

electrical cables, water pipes and gas pipes. Do not drill into structures unless you have established it’s safe to do so.

COMPONENT CHECKLIST

NOTE:

! Wall Plate Mounting Fasteners are supplied with Wall Mounts. NOT

Professional installer to ensure correct Mounting Fastener type, location &

quantity to suit structure where Wall Mount is installed.

! ALWAYS use a washer between the chosen fastener and the wall plate.

! Mounting fasteners to be used as per manufacturers instructions, including

minimum engagement to achieve necessary performance. 0 - 100kg

(0 - 220lb)

WEIGHT RANGE

Installation Guide

AD-WF-10090

Fixed Wall Mount 10090

REQUIRED TOOLS

• Phillips head screwdriver

• Power drill

• Suitable drill bit

• Driver bit for selected

wall fasteners

• Stud nder

• Spirit level

AD-WF-10090 Page 2 of 2

Slot Dimension

Ø8 x 46mm

12 3

1. Mount the Wall Plate to the Wall

*Fasteners shown are for example only

M-H (OPTIONAL)

SPACER HEIGHT (mm)

M-G (OPTIONAL)

M-A

M-B

M-C

M-D

M-E

(M5x14)

(M6x14)

(M6x30)

(M8x30)

(M8x50)

M-F

403530252015105

3. Hook the Display onto the Wall Plate 4. Check Security and Conceal Straps

3.1. Angle the display and hook the Display Brackets over

the top of the Wall Plate. This should be completed by

two people.

3.2. The silver locking tabs on the Display Brackets will

make a “click” sound to conrm a secure installation.

You may need to gently apply pressure to the

lower half of the display if this does not happen

automatically.

4.1. Gently pull the display forwards from bottom of the

display to ensure the the locking tabs have engaged

with the wall plate and the display cannot be tilted

upwards.

4.2. Conceal straps behind the display using the magnets

at the end of each strap to prevent accidental unlock

and dismount of the display.

NOTE:

Ensure the silver locking

tabs are pushed in prior

to mounting the display.

NOTE:

To unlock display from the Wall Plate for display removal

- retrieve the straps from their concealed position and pull

each strap down once briey until a “click” is heard.

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

NOTE:

• Choice and supply of appropriate wall plate fasteners is the

responsibility of the installer.

• Consult a preferred fastener supplier or a structural engineer

to select fasteners which are most appropriate for the weight

of the display and wall construction method.

• Wall plate be level. Verify using a quality spirit level tool.must

• On a Stud Wall or Drywall use a good quality Stud Finder to

position mounting fasteners in the centre of studs.

• On a Masonry Wall avoid positioning Wall Plate mounting

fasteners in a mortar join.

NOTE:

• Always use multi-washers M-F.

• Ensure the display brackets are

not loose and screws are not

forced too deep into the display.

• If spacers are needed, use the

shortest possible combination

between the display bracket and

the display.

2. Attach the Display Brackets to the Display

Specyfikacje produktu

Marka:	Atdec
Kategoria:	Wsparcie dla płaskich paneli
Model:	AD-WF-10090

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Atdec AD-WF-10090, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Wsparcie dla płaskich paneli Atdec

Atdec AWMS-DW6-S Instrukcja

7 Grudnia 2024

Atdec AWM-W-S Instrukcja

7 Grudnia 2024

Atdec AWMS-46W35-S Instrukcja

7 Grudnia 2024

Atdec AWMS-HX40-H-B Instrukcja

7 Grudnia 2024

Atdec AD-WF-8060 Instrukcja

7 Grudnia 2024

Atdec AD-WT-8060 Instrukcja

7 Grudnia 2024

Atdec AD-WF-10090 Instrukcja

7 Grudnia 2024

Atdec AWM-W-B Instrukcja

7 Grudnia 2024

Atdec AD-WFP-5040 Instrukcja

7 Grudnia 2024

Atdec TH-1030-VFM Instrukcja

22 Września 2024

Instrukcje Wsparcie dla płaskich paneli

Najnowsze instrukcje dla Wsparcie dla płaskich paneli

B-tech BT9340-FM Instrukcja

15 Stycznia 2025

StarTech.com ARMPIVOTE2 Instrukcja

15 Stycznia 2025

StarTech.com 3M1A3SG-MONITOR-ARM Instrukcja

15 Stycznia 2025

Vogel's FM1622 Instrukcja

15 Stycznia 2025

NeoMounts DS45-430BL16 Instrukcja

14 Stycznia 2025

NeoMounts DS42-430BL14 Instrukcja

14 Stycznia 2025

NeoMounts NS-WMB300PBLACK Instrukcja

14 Stycznia 2025

StarTech.com MONSTADJD Instrukcja

14 Stycznia 2025

Manhattan 424868 Instrukcja

14 Stycznia 2025

Manhattan 424820 Instrukcja

14 Stycznia 2025