Instrukcja obsługi Atdec AD-WFP-5040

Atdec Wsparcie dla płaskich paneli AD-WFP-5040

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Atdec AD-WFP-5040 (2 stron) w kategorii Wsparcie dla płaskich paneli. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

AD-WFP-5060 Page 1 of 2

REQUIRED TOOLS

• Phillips head screwdriver

• Power drill

• Suitable drill bit

• Driver bit for selected

wall fasteners

• Stud nder

• Spirit level

Wall Plate

Spirit Level

M-A

M5x14 (x4)

Screw

M-B

M6x14 (x4)

Screw

M-C

M6x30 (x4)

Screw

M-G

Short Spacer

(x8)

M-H

Long Spacer

(x8)

M-F

Multi Washer

(x4)

M-D

M8x30 (x4)

Screw

M-E

M8x50 (x4)

Screw

Display Bracket (x2)

Installation Guide

AD-WFP-5040

Portrait Fixed Wall Mount 5040

IMPORTANT INFORMATION

! Please ensure this product is installed as per these installation instructions.

! The manufacturer accepts no responsibility for incorrect installation.

! Failure to mount this product correctly may cause serious injury/death during or following installation.

! This product is not suitable for outdoor use.

! Do not use this product for mobile applications.

! This product supports a maximum load of 50kg (110lb).

! Wall Plate only achieves maximum weight rating when appropriately fastened to a wall of adequate structural capacity.

! Professional installer to ensure adequate structural capacity of wall (including appropriate safety factor) to support total

weight of all equipment being mounted.

! Drilling into electrical wires can cause death - use appropriate equipment and caution when drilling holes in walls to avoid

electrical cables, water pipes and gas pipes. Do not drill into structures unless you have established it’s safe to do so.

! Suits displays with mounting hole patterns from 75mm to 410mm wide by 70mm to 605mm high.

COMPONENT CHECKLIST

0 - 50kg

(0 - 110lb)

WEIGHT RANGE

NOTE:

! Wall Plate Mounting Fasteners are supplied with Wall Mounts. NOT Professional

installer to ensure correct Mounting Fastener type, location & quantity to suit

structure where Wall Mount is installed.

! ALWAYS use a washer between the chosen fastener and the wall plate.

! Mounting fasteners to be used as per manufacturers instructions, including

minimum engagement to achieve necessary performance.

AD-WFP-5060 Page 2 of 2

Slot Dimension

Ø8 x 40mm

*Fasteners shown are not included

NOTE:

• Always use multi-washers M-F.

• Use the shortest combination of spacers (if necessary) ensuring the

display is not loose and screws are not forced too deep into the display.

M-C (M6x30) /

M-D (M8x30)

M-C (M6x30) /

M-D (M8x30)

M-F

M-G

M-F

M-G

M-H

M-F M-F

M-G

M-HM-H

M-G

M-F

M-H

M-F

M-C (M6x30) /

M-D (M8x30)

M-E (M8x50) M-E (M8x50) M-E (M8x50)

M-A (M5x14) /

M-B (M6x14)

M-F

No portion of this document or any artwork contained herein should be reproduced in any way without

the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer

12 3

1. Mount the Wall Plate to the Wall

NOTE:

• Choice and supply of appropriate wall plate fasteners is the

responsibility of the installer.

• Consult a preferred fastener supplier or a structural engineer to

select fasteners which are most appropriate for the weight of

the display and wall construction method.

• Wall plate be level. Verify using a quality spirit level tool must

or the included spirit level C

• On a Stud Wall or Drywall use a good quality Stud Finder to

position mounting fasteners in the centre of studs.

• On a Masonry Wall avoid positioning Wall Plate mounting

fasteners in a mortar join.

2. Attach the Display Brackets to the Display

3. Hook the Display onto the Wall Plate 4. Conceal Straps and Lock Display

3.1. Angle the display and hook the Display Brackets over the top

of the Wall Plate. This should be completed by two people.

3.2. While supporting the display, simultaneously pull each strap

down and lower the display until it is parallel with the wall.

NOTE:

To ensure the display brackets have engaged with the wall

plate and the display cannot be tilted upwards, gently pull

the display forwards from the bottom of the display.

4.1. Conceal straps behind the display ensuring they are not

visible from the desired viewing angle

4.2. (OPTIONAL) To prevent theft of the display, add a

padlock to each display bracket.

NOTE:

Releasing the display from the Wall Plate requires two

people. To do so, retrieve each strap from its concealed

position, then pull both straps downward and whilst holding

them down, tilt the display upwards to clear the lower edge

of the Wall Plate. The straps can then be released and the

display lifted off. This should be completed by two people.

Max. Ø4.5mm

Specyfikacje produktu

Marka:	Atdec
Kategoria:	Wsparcie dla płaskich paneli
Model:	AD-WFP-5040

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Atdec AD-WFP-5040, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Wsparcie dla płaskich paneli Atdec

Atdec AWMS-DW6-S Instrukcja

7 Grudnia 2024

Atdec AWM-W-S Instrukcja

7 Grudnia 2024

Atdec AWMS-46W35-S Instrukcja

7 Grudnia 2024

Atdec AWMS-HX40-H-B Instrukcja

7 Grudnia 2024

Atdec AD-WF-8060 Instrukcja

7 Grudnia 2024

Atdec AD-WT-8060 Instrukcja

7 Grudnia 2024

Atdec AD-WF-10090 Instrukcja

7 Grudnia 2024

Atdec AWM-W-B Instrukcja

7 Grudnia 2024

Atdec AD-WFP-5040 Instrukcja

7 Grudnia 2024

Atdec TH-1030-VFM Instrukcja

22 Września 2024

Instrukcje Wsparcie dla płaskich paneli

Najnowsze instrukcje dla Wsparcie dla płaskich paneli

Rocstor Y10N027-B1 Instrukcja

11 Grudnia 2024

StarTech.com ARMQUADSS Instrukcja

10 Grudnia 2024

CTA Digital ADD-AVPMB Instrukcja

10 Grudnia 2024

Gabor FPC-85 Instrukcja

10 Grudnia 2024

Gabor FPS-L Instrukcja

10 Grudnia 2024

Gabor TM-UL Instrukcja

10 Grudnia 2024

Kanto FMX2 Instrukcja

9 Grudnia 2024

Gabor FSM-L Instrukcja

9 Grudnia 2024

Chief TS218SU Instrukcja

9 Grudnia 2024

Dell MDS19 Instrukcja

8 Grudnia 2024