Instrukcja obsługi Atdec SD-POS-VBM

Atdec Wsparcie dla płaskich paneli SD-POS-VBM

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Atdec SD-POS-VBM (2 stron) w kategorii Wsparcie dla płaskich paneli. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
A. Determine the degree of
rotation you require. (Refer to
Mounting Options above)
B. To Limit the Rotation,
use the 2.5mm Allen Key to
insert the supplied M5
Grub Screw into your
chosen Locking Hole until it
sits flush with the Base Plate.
NOTE: If you want the full
355° rotation, you do NOT
need to install a grub screw.
Step 1. Limit Rotation
Component Checklist (Check you have received all parts against the Component Checklist below)
M4x10mm Screws (x4)
M4x16mm Screws (x4)
POS Assembly (x1)
Hardware
2.5mm Allen Key (x1)
M4x12mm Screws (x4)
Installation Instructions
Installation Template
(x1)
M5 Grub Screw (x1)
4 x Ø3mm (1/8”)
Pilot Holes
Centre for
45mm(1¾”) Cable
Access Hole
Mounting Options
A. Position the Installation
Template in the desired location
on your work surface. Ensure the
straight edge sits perpendicular
with the User’s line of sight. Mark
the center points of each of the
required holes onto the work
surface with a pencil.
B. Drill 4 x 3mm (1/8”) Pilot
Holes to a depth of 15mm (9/16”).
Use a 45mm (1¾”) hole saw to
drill the Cable Access Hole in the
work surface.
C. Reposition POS Multi with
the “Direction Arrow” pointing in
the direction required for your
chosen rotation. Secure the POS
to the work surface using the
supplied 14 Gauge Screws (x4).
INSTALLATION
TEMPLATE
Top Cap (x1)
Screw Cover
(x1)
14 Gauge Screws (x4)
0° Locking Hole (Fixed)
0-180° Locking Hole
0-270° Locking Hole
0-90° Locking Hole
Direction Arrow
Locking Holes
Rotation Options
0° Rotation (Fixed)
0-90° Rotation
0-180° Rotation
0-270° Rotation
0-355° Rotation
OR
4x
M5x75mm Screws
(To suit 70mm
4x M5
Cable Management
Hole
14 Gauge
Screws (x4)
Ø45mm
(1¾”) Cable
Access Hole
4 x Ø3mm (1/8”)
Pilot Holes
USER
USER
5° Gap in
Rotation
USER
Step 2. Locate and Secure your POS Multi
5° Gap in
Rotation
270°
180°
0°
90°
270°
180°
0°
90°
355°
355°
M5 Grub Screw
Your POS Multi offers 355° of
Rotation. This can also be limited
to suit a specific application.
The Direction in which you
mount POS Multi will determine
where the 5° gap in Rotation is
located, and how you choose to
limit the rotation.
2.5mm Allen Key
Base Plate
Direction
Arrow
Direction
Arrow
2mm Allen Key (x1)
Display | POS Multi
SD-POS-VBM
Security Screw (x1)
Tightening Tool (x1)
VESA plate (x1)
A. Loop the Security Cable
(Kensington or similar)
around the internal post
of the POS Assembly.
B. Feed the other
end
of the cable through
the POS Assembly and
out the Cable
Management Hole.
C. After you have attached the monitor
(As directed in ) install the lock to theStep 8
monitor as per the manufacturer guidelines.
Step 5. Install Top Cap
Step 4. (Optional) Install Monitor Security Cable (Security Cable NOT Included)
Prior to attaching your monitor,
install the monitor cables.
Run them through the Cable
Management Hole, down the
pole and out the Cable Access
Hole in the work surface.
Step 6. Install Monitor Cables
Top Cap Cable
Management
Hole
OUT
IN
Step 3. Attach Screw Cover
Remove the paper backing from the Screw
Cover and adhere to the POS base as shown.
Screw
Cover
These Installation Instructions secure
the POS Multi using the provided
fasteners from above thework surface.
For advanced Security Installation from
below the work surface. Please refer to
the Advanced Security Installation
Addendum.
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 27.07.09 ©
Position your Display to the desired viewing
angle, using the 40° angular movement
allowed by the VESA Ball Mount.
If the display does not hold its position,
or is too resistant, adjust the Tension Plate
(see diagram right).
To make any adjustments, use the
Tightening Tool supplied.
Top of
Display
There are two mounting hole configurations:
UÊÇxÊÝÊÇx
UÊ£ääÊÝÊ£ää
Choose appropriate Mounting Screws
from the Hardware supplied to suit
your Display.
Mounting Screws (x4)
VESA Plate
Back of Display
Çx
(3”) £ää
(4”)
Çx
(3”)
£ää
(4”)
Step 7. Attach the VESA plate to your Display
Step 8. Attach your Display to the POS Assembly
Step 9. Adjust the VESA Ball Mount Advanced Security Installation
PUSH
Push down firmly to attach the Top Cap.
Hook the top of the VESA plate onto
the Quickshift Mount.
Gently push the bottom of the Display
into the Mount until you hear a ‘CLICK’.
Insert the Security Screw, and tighten
using the 2mm Allen Key supplied.
Tighten (+Kg)
Loosen (-Kg)
Tension
Plate
Tightening
Tool
Security
Screw
CLICK
PUSH
HOOK
TIGHTEN
Back of Display
2mm
Allen Key

Specyfikacje produktu

Marka: Atdec
Kategoria: Wsparcie dla płaskich paneli
Model: SD-POS-VBM

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Atdec SD-POS-VBM, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Wsparcie dla płaskich paneli Atdec

Atdec

Atdec TH-1030-VFM Instrukcja

22 Września 2024
Atdec

Atdec TH-30-50-RW Instrukcja

22 Września 2024
Atdec

Atdec TH-3070-UF flat panel wall mount Instrukcja

22 Września 2024
Atdec

Atdec TH-3070-CTW Instrukcja

22 Września 2024
Atdec

Atdec L-PB Instrukcja

21 Września 2024
Atdec

Atdec VF-AT-W/TAA Instrukcja

21 Września 2024
Atdec

Atdec SD-DP-750 Instrukcja

21 Września 2024
Atdec

Atdec VF-AT-D Instrukcja

21 Września 2024
Atdec

Atdec AF-AT-D Instrukcja

21 Września 2024
Atdec

Atdec VFS-DH/TAA Instrukcja

21 Września 2024

Instrukcje Wsparcie dla płaskich paneli

Najnowsze instrukcje dla Wsparcie dla płaskich paneli

NEC

NEC PDVWXUN 55 P Instrukcja

15 Października 2024
Insignia

Insignia NS-STV3N1705 Instrukcja

15 Października 2024
One For All

One For All DM 4110 Instrukcja

9 Października 2024
One For All

One For All DM 7220 Instrukcja

9 Października 2024
One For All

One For All DM 2220 Instrukcja

9 Października 2024
Kogan

Kogan KASMM39S12A Instrukcja

9 Października 2024
Kogan

Kogan KATWM70TLMA Instrukcja

9 Października 2024
Kogan

Kogan KADMM46G24A Instrukcja

9 Października 2024
Kogan

Kogan KADMMPCGASC Instrukcja

9 Października 2024
One For All

One For All DM 2210 Instrukcja

9 Października 2024