Instrukcja obsługi Anton/Bauer QRC-Digital

Anton/Bauer nieskategoryzowany QRC-Digital

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Anton/Bauer QRC-Digital (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Anton/Bauer Inc., 14 Progress Drive, Shelton, Connecticut 06484 USA • (203) 929-1100 • Fax (203) 925-4988 • support@antonbauer.com

Europe, B.V. Eurode Business Center, Eurode-Park 1-2, 6461 KB Kerkrade, The Netherlands • (+31) 45 5639220 • Fax (+31) 45 5639222 • eurosupport@antonbauer.com

Singapore Office - Anton/Bauer, 6 New Industrial Road, # 02-02 Hoe Huat Ind. Bld., Singapore 536199 • (+65) 62975784 • Fax (+65) 62825235

www.antonbauer.com 7595-0282 Rev E

QRC GOLD

Installation Instructions

A7595-0282 Rev E

DA-E751 Sht 1 of 2

FEATURES

CAUTION: Open + and – wires inside bracket. DO NOT attach battery without terminating wires.

1. Cam action latch for improved ease of battery loading and removal. Red label below latch indicates battery is not fully

latched, eliminating inadvertent battery unloading.

2. PowerTap® Connector. A built-in fused 10 amp connector for powering Ultralight® portable camera light and

accessories. NOTE: Requires PowerTap connector. The PowerTap connector is included on all Ultralight 2 light

assemblies and cable assemblies for the older Ultralight SINGLE or DUAL.

3. Mounting Pattern. The Snap-On Gold Mount bracket is fully compatible with all existing cameras and batteries using

the Anton/Bauer mounting system. NOTE: When custom mounting the Gold Mount bracket system it is necessary to

support the shaded areas (see Fig. A) against a flat surface. A backplate is provided with each Gold Mount bracket for

this purpose.

4. PowerTap Fuse Holder. The fuse holder for the PowerTap connector. The fuse holder located in the bracket is press

fit. To remove the fuse holder,

ras

the main fuse holder bod

and

ull u









Compact universal Gold Mount® kit with mounting hardware and wire terminals, most DC powered professional video

equipment utilize specific Gold Mount models (see Anton/Bauer catalog’s Gold Mount section and Product Application Guide).

The QRC-Gold is ideal for adapting video devices where no other Gold Mount is specified. Before adapting the QRC-Gold to

any video device for the first time, check to confirm compatibility with an Anton/Bauer 14.4 volt battery.

Approved Copy

A7595-0282 Rev E

DA-E751 Sht 2 of 2

To replace the fuse:

A. Remove the fuse from the fuse holder by pushing the assembly through the square access opening in the main body.

B. Pull the press fit fuse caps from both ends of the spent fuse and replace with a new fuse. (Note: The replacement fuse must be a 10

amp 250 volt 5 x 20mm fuse).

Manufacturer’s part numbers: Anton/Bauer (3713-1010), Schurter (001.2514), or Little Fuse (218-010)

C. Replace both fuse caps onto the new fuse and press the fuse assembly back into the main body.

D. Press the fuse holder back into its original location within the bracket.

5. Banana Pins. The Gold Mount Banana Pins are gold plated with eight contact points for ultra-low resistance and optimum dependability.

Both pins are externally removable with a 4mm hex nut driver for ease of serviceability. NOTE: When reinstalling pins, caution should

be taken not to over tighten the pin assembly.

Replacement Banana pins are available only through the Anton/Bauer Customer Support Group. The Anton/Bauer part number is 3320-

0105.



SERVICE

If you have any questions regarding this Anton/Bauer product, please call our Customer Support Group at 1-800-541-1667. If repair or appraisal is

necessary, ship your product prepaid, together with proof of purchase, to Anton/Bauer Inc., 14 Progress Drive, Shelton, CT 06484 ATTENTION:

SERVICE DEPARTMENT.

Use of unauthorized equipment in conjunction with Anton/Bauer products constitutes misuse under our warranties and may limit or void

those warranties. Anton/Bauer does not authorize, condone, recommend, or otherwise assume any liability or responsibility resulting from the

use of any battery, charger or accessory made by Anton/Bauer manufacture with any battery, charger or accessory not manufactured,

produced or sold by Anton/Bauer. Anton/Bauer only authorizes the use of original Anton/Bauer product with this product. Use only original

Anton/Bauer equipment with this product.

Approved Copy

Specyfikacje produktu

Marka:	Anton/Bauer
Kategoria:	nieskategoryzowany
Model:	QRC-Digital
Kolor produktu:	Czarny
Wysokość produktu:	119.4 mm
Szerokość produktu:	76.2 mm
Głębokość produktu:	12.7 mm