Instrukcja obsługi Anton/Bauer QR-gold

Anton/Bauer nieskategoryzowany QR-gold

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Anton/Bauer QR-gold (2 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

QR-GOLD

Installation Instructions

The Gold Mount

Battery System is an advanced design of the popular Anton/Bauer

Snap-On

Mounting System currently

being used by virtually every professional video camera manufacturer in the world.

FEATURES

CAUTION: Open + and – wires inside bracket. DO NOT attach battery without terminating wires.

1. Cam action latch for improved ease of battery loading and removal. Red label below latch indicates battery is not fully

latched, eliminating inadvertent battery unloading.

2. Safety lock provides user with a safety for the latch mechanism. Will allow battery to remain in the fully latched position in

the event the mounted battery is shocked or latch mechanism is accidentally depressed. Green label below safety

indicates locked “shoot” position.

(continued)

Approved Copy

Anton/Bauer Inc., 14 Progress Drive, Shelton, Connecticut 06484 USA • (203) 929-1100 • Fax (203) 925-4988 • support@antonbauer.com

Europe, B.V. Eurode Business Center, Eurode-Park 1-2, 6461 KB Kerkrade, The Netherlands • (+31) 45 5639220 • Fax (+31) 45 5639222 • eurosupport@antonbauer.com

Singapore Office - Anton/Bauer, 6 New Industrial Road, # 02-02 Hoe Huat Ind. Bld., Singapore 536199 • (+65) 62975784 • Fax (+65) 62825235

www.antonbauer.com 7595-0079 Rev N

3. PowerTap® Connector. A built-in fused 10 amp connector for powering Ultralight

® portable camera light and

accessories. NOTE: Requires PowerTap connector. The PowerTap connector is included on all Ultralight 2 light

assemblies and cable assemblies for the older Ultralight SINGLE or DUAL.

4. Mounting Pattern. The Snap-On Gold Mount bracket is fully compatible with all existing cameras and batteries using the

Anton/Bauer mounting system. NOTE: When custom mounting the Gold Mount bracket system it is necessary to

support the shaded areas (see Fig. A) against a flat surface. A backplate is provided with each Gold Mount bracket for

this purpose.

5. PowerTap Fuse Holder. The fuse holder for the PowerTap connector. The fuse holder located in the bracket is press fit.

To remove the fuse holder, grasp the main fuse holder body and pull up.

To replace the fuse:

A. Remove the fuse from the fuse holder by pushing the assembly through

the square access opening in the main body.

B. Pull the press fit fuse caps from both ends of the spent fuse and replace with a new fuse. (Note: The replacement

fuse must be a 10 amp 250 volt 5 x 20mm fuse).

Manufacturer’s part numbers: Anton/Bauer (3713-1010)

Schurter (001.2514)

Little Fuse (218-010)

C. Replace both fuse caps onto the new fuse and press the fuse assembly back into the main body.

D. Press the fuse holder back into its original location within the bracket.

6. Banana Pins. The Gold Mount Banana Pins are gold plated with eight contact points for ultra-low resistance and

optimum dependability. Both pins are externally removable with a 4mm hex nut driver for ease of serviceability.

NOTE: When reinstalling pins, caution should be taken not to over tighten the pin assembly. Replacement Banana pins

are available only through the Anton/Bauer Service Department. The Anton/Bauer part number is 3320-0105.

Use of unauthorized equipment in conjunction with Anton/Bauer products constitutes misuse under our warranties and

may limit or void those warranties. Anton/Bauer does not authorize, condone, recommend, or otherwise assume any

liability or responsibility resulting from the use of any battery, charger or accessory made by Anton/Bauer manufacture

with any battery, charger or accessory not manufactured, produced or sold by Anton/Bauer. Anton/Bauer only authorizes

the use of original Anton/Bauer product with this product. Use only original Anton/Bauer equipment with this product.

Approved Copy

Specyfikacje produktu

Marka:	Anton/Bauer
Kategoria:	nieskategoryzowany
Model:	QR-gold
Kolor produktu:	Czarny
Wysokość produktu:	119.4 mm
Szerokość produktu:	94 mm
Głębokość produktu:	12.7 mm