Instrukcja obsługi Antari Z-4
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Antari Z-4 (7 stron) w kategorii Maszyna efektów. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/7

1
Z-SERIES USER MANUAL
Congratulations on the purchase of your new
ANTARI Z-SERIES FOG MACHINE.
Save and read these instructions
2000 Antari Lighting and Eects Ltd.

2
User Manual
Antari Fog Machine
Congratulations on the purchase of your new
ANTARI Z Series FOG MACHINE.
Introduction
Thank you for choosing an ANTARI Fog Machine. You now own a rugged and powerful
state- -the-art machine. Prior to use, we suggest that you carefully read all of the of
instructions. By following the suggestions found in this user manual, you can look forward to
the reliable and satisfactory performance of your ANTARI Fog Machine for years to come.
Please follow these operation, safety and maintenance instructions to
ensure a long and safe life for your fog machine.
Cautions
Danger of electric shock
Keep this device dry.
For inside use only. Not designed for outside use.
For the 110V models, use 3-prong grounded electrical outlet only. Prior to use take care
to determine that the unit is installed at the rated voltage.
Always unplug your ANTARI Fog Machine before lling its tank.
Keep fog machine upright.
Turn off or unplug when not in use.
This machine is not water- or splash-proof. If moisture, water, or fog liquid gets inside the
housing, immediately unplug the unit and contact a service technician or your ANTARI
dealer before using it again.
No user serviceable parts inside. Refer to your ANTARI dealer or other qualied service
personnel.
Danger of burns
For adult use only. Fog machine must be installed out of the reach of children. Never
leave the unit running unattended.
Never aim the output nozzle directly at people.
Fog machine output is very hot. Avoid coming within 60 cm of the output nozzle during
operation.
Locate the fog machine in a well-ventilated area. Never cover the unit’s vents. In order to
guarantee adequate ventilation, allow a free air space of at least 20 cm around the sides
and top of the unit.
Never aim the output nozzle at open flames.
The output nozzle becomes very hot during operation (300 degrees C). Keep ammable
materials at least 50 cm away from the nozzle.
Always allow your ANTARI Fog Machine to cool down before attempting to clean or
service it.

3
Danger of explosion
Never add ammable liquids of any kind (oil, gas, perfume) to the fog liquid.
Pay attention to all warning labels and instructions printed on the exterior of your ANTARI
Fog Machine
Use only the high-quality, water-based fog liquid that your dealer recommends. Other fog
liquids may cause clogging or “spitting”.
Always make sure there is sufcient liquid in the fog liquid tank. Operating this unit
without liquid will cause damage to the pump as well as over-heating of the heater.
If your ANTARI Fog Machine fails to work properly, discontinue use immediately. Drain all
fog liquid from the tank, pack the unit securely (preferably in the original packing material),
and return it to your ANTARI dealer for service.
Always drain tank before mailing or transporting this unit.
Never drink fog liquid. If it is ingested, call a doctor immediately. If fog liquid comes in
contact with skin or eyes, rinse thoroughly with water.
Unpacking & Inspection
Open the shipping carton and verify that all equipment necessary to operate the system has
arrived intact. Refer to the “Features” section for information on what items are included with
your model. If any equipment is missing contact your ANTARI dealer immediately.
Before beginning initial setup of your ANTARI Fog Machine, make sure that there is no
evident damage caused by transportation. In the event that the unit’s housing or cable is
damaged, do not plug it in and do not attempt to use it until after contacting your ANTARI
dealer for assistance.
Setup
Remove all packing materials from shipping box. Check that all foam and plastic padding
is removed, especially in the nozzle area.
Place fog machine on a at surface and remove fog liquid tank cap.
Fill with ANTARI Fog Liquid or other high-quality water-based fog fluid. Any other types of
uid can damage the unit. When filled, place cap back on liquid tank.
Firmly attach the remote control cable to the proper input on the rear of the machine.
Operation
Plug power cord into a grounded electrical outlet. If necessary, turn power switch on rear
of unit to “ON” position. Warm-up is complete when green lamp lights up on remote unit.
To emit fog, press the appropriate button on the remote for the desired length of time.
he machine re-heats to the proper The remote unit’s lamp will cycle on and off as t
operating temperature.
For further information on operating your ANTARI Fog Machine, see the section titled,
“Remote Control Operation”.
If your model includes a mounting bracket designed for overhead installation, it may be
installed at floor level or suspended overhead. If the unit is to be mounted using the bracket,
it is important that the fog does not shoot directly at any one’s face. Whatever installation
method you choose, do not allow the unit to have more than a 15 degree angle of inclination.
Specyfikacje produktu
Marka: | Antari |
Kategoria: | Maszyna efektów |
Model: | Z-4 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Antari Z-4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Maszyna efektów Antari

5 Marca 2025

5 Marca 2025

5 Marca 2025

5 Grudnia 2024

8 Października 2024

28 Września 2024

20 Września 2024

19 Września 2024

17 Września 2024

16 Września 2024
Instrukcje Maszyna efektów
- Maszyna efektów BeamZ
- Maszyna efektów Behringer
- Maszyna efektów Nedis
- Maszyna efektów American DJ
- Maszyna efektów Boss
- Maszyna efektów Westinghouse
- Maszyna efektów Chauvet
- Maszyna efektów Viking
- Maszyna efektów Eurolite
- Maszyna efektów Velleman
- Maszyna efektów Manta
- Maszyna efektów Pyle
- Maszyna efektów NGS
- Maszyna efektów Showtec
- Maszyna efektów TC Electronic
- Maszyna efektów Klark Teknik
- Maszyna efektów Doepfer
- Maszyna efektów Cameo
- Maszyna efektów Lotronic
- Maszyna efektów Elation
- Maszyna efektów Futurelight
- Maszyna efektów Martin
- Maszyna efektów Monacor
- Maszyna efektów HQ Power
- Maszyna efektów Karma
- Maszyna efektów Magmatic
- Maszyna efektów Technical Pro
- Maszyna efektów Adj
- Maszyna efektów Steren
- Maszyna efektów Valcom
- Maszyna efektów QTX
- Maszyna efektów Konig
- Maszyna efektów Valueline
- Maszyna efektów Fredenstein
- Maszyna efektów HQ
- Maszyna efektów Max
- Maszyna efektów Monoprice
- Maszyna efektów ColorKey
- Maszyna efektów Elysia
- Maszyna efektów Black Lion Audio
- Maszyna efektów Laserworld
- Maszyna efektów JB Systems
- Maszyna efektów Evo-Lite
- Maszyna efektów Blizzard
- Maszyna efektów Hazebase
- Maszyna efektów IGS Audio
- Maszyna efektów Sagitter
- Maszyna efektów Fun Generation
- Maszyna efektów IMG Stage Line
- Maszyna efektów Lexicon
- Maszyna efektów The Confetti Maker
- Maszyna efektów BoomTone DJ
- Maszyna efektów TCM FX
- Maszyna efektów Audibax
Najnowsze instrukcje dla Maszyna efektów

27 Lutego 2025

14 Stycznia 2025

5 Stycznia 2025

5 Stycznia 2025

5 Stycznia 2025

5 Stycznia 2025

5 Stycznia 2025

5 Stycznia 2025

5 Stycznia 2025

5 Stycznia 2025