Instrukcja obsługi Antari Z-3000 MK2


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Antari Z-3000 MK2 (32 stron) w kategorii Maszyna efektów. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/32
Z-1200II, Z-1500II & Z-3000II USER MANUAL
Z-1200II, Z-1500II & Z-3000II BEDIENUNGSANLEITUNG
MODE D’EMPLOI des Z-1200II, Z-1500II & Z-3000II
Congratulations on the purchase of your new
ANTARI Z-SERIES II FOG MACHINE.
Wir beglückwünschen Sie zum Kauf Ihres neuen ANTARI Z-SERIES NEBELGERÄTES.
Nous vous félicitons pour l’achat de votre nouvelle
Z-SERIES machine à fumée d’ANTARI.
Read and save these instructions
Bitte lesen Sie diese Anweisungen und bewahren Sie sie gut auf
Lisez et Gardez ces instructions
©
©
©
©© 2006 Antari Lighting and Eects Ltd.
2
TeUser Manual
Antari Z-1200II, Z-1500II and Z-3000II Fog Machine
Congratulations on the purchase of your new
ANTARI Z-Series II FOG MACHINE.
Introduction
Thank you for choosing a ANTARI Z-Series II Fog Machine. You now own a rugged and powerful state-of-
the-art machine. Prior to use, we suggest that you carefully read all of the instructions. By following the
suggestions found in this user manual, you can look forward to the reliable and satisfactory performance of
your ANTARI Fog Machine for years to come.
Please follow these operation, safety and maintenance instructions to ensure a long and safe life for your
fog machine.
CAUTION:
Risk of electric shock. Disconnect the appliance from the electric supply before refilling liquid, cleaning or
performing maintenance on the machine.
Danger of Electric Shock
Keep this device dry.
For inside use only. Not designed for outside use.
For the 110V models, use 3-prong grounded electrical outlet only. Prior to use take care to determine that
the unit is installed at the rated voltage.
Always unplug your ANTARI Z-Series II Fog Machine before filling its tank.
Always keep fog machine in upright position.
Turn off or unplug the machine when not in use.
This machine is not water-proof. If moisture, water, or fog fluid gets inside the housing, immediately unplug
the unit and contact a service technician or your ANTARI dealer before using it again.
No user serviceable parts inside. Refer to your ANTARI dealer or other qualified service personnel.
Danger of Burns
This device is for adult use only and must be installed out of the reach of children. Never leave the unit
running unattended.
Never aim the output nozzle directly at people.
Fog machine output is very hot. Avoid coming within 60 cm of the output nozzle during operation.
Locate the fog machine in a well-ventilated area. Never cover the unit’s vents. In order to guarantee
adequate ventilation, allow a free air space of at least 20 cm around the sides and top of the unit.
Never aim the output nozzle at open flames.
3
If the supply cord is damaged, it must be replaced by manufacturer or its service agent or similarly qualified
personnel in order to avoid a hazard.
The output nozzle becomes very hot during operation (200°C). Keep flammable materials at least 50 cm
away from the nozzle.
Always allow your ANTARI Fog Machine to cool down before attempting to clean or service it.
Danger of Explosion
Never add flammable liquids of any kind (such as oil, gas, perfume) to the fog liquid.
Use only high-quality, water-based fog liquid that your dealer recommends. Other fog liquids may cause
clogging or “spitting”.
Always make sure there is sufficient liquid in the tank. Operating this unit without liquid will cause damage
to the pump as well as over-heating of the heater.
If your ANTARI Z-1200II, Z-1500II or Z-3000II Fog Machine fails to work properly, discontinue use
immediately. Drain all fog liquid from the tank, pack the unit securely (preferably in the original packing
material), and return it to your ANTARI dealer for service.
Always drain tank before mailing or transporting this unit.
Never drink fog liquid. If it is ingested, call a doctor immediately. If fog liquid comes in contact with skin or
eyes, rinse thoroughly with water.
Note: Pay attention to all warning labels and instructions printed on the exterior of your ANTARI Fog Machine
Unpacking & Inspection
Open the shipping carton and verify that all equipment necessary to operate the system has arrived intact.
The shipping carton should contain the following items:
1. One unit of Z-Series II Fog Machine with power cord
2. Mounting brackets with washers/screws (for Z-1200II)
3. Z-8 Multi-function remote control with attached cord (for Z-1200II)
4. Z-20 multi-function remote control with attached cord (for Z-1500II & Z-3000II)
5. User Manual
If any equipment is missing contact your ANTARI dealer immediately.
Before beginning your initial setup on ANTARI Z-1200II, Z-1500II or Z-3000II Fog Machine, make sure that
there is no evident damage caused by transportation. In the event that the unit’s housing or cable is damaged,
do not plug it in and do not attempt to use it until after contacting your ANTARI dealer for assistance.
Setup
Remove all packing materials from shipping box. Check that all foam and plastic padding is removed,
especially in the nozzle area.
Place fog machine on a flat surface and remove fog liquid tank cap.
Fill with high-quality, water-based fog liquid recommended by ANTARI dealer. Any other types of fluid can
damage the unit resulting in spitting and serious clogging problem. When filled, place cap back on liquid
tank.
Be careful not to exceed the maximum fluid level. DO NOT OVERFILL.
Firmly attach the Z-8 or Z-20 control module cable to the connector inside the rear chamber of the machine.


Specyfikacje produktu

Marka: Antari
Kategoria: Maszyna efektów
Model: Z-3000 MK2

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Antari Z-3000 MK2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Maszyna efektów Antari

Antari

Antari F-7X Instrukcja

8 Października 2024
Antari

Antari S-120 Instrukcja

28 Września 2024
Antari

Antari MB-55 Instrukcja

20 Września 2024
Antari

Antari Z-1500 MK2 Instrukcja

19 Września 2024
Antari

Antari Z-9 Instrukcja

17 Września 2024
Antari

Antari DNG-250 Instrukcja

16 Września 2024
Antari

Antari F-80 Instrukcja

16 Września 2024
Antari

Antari Z-3000 MK2 Instrukcja

16 Września 2024
Antari

Antari M-10 Instrukcja

15 Września 2024
Antari

Antari Z-1200 MKII Instrukcja

13 Września 2024

Instrukcje Maszyna efektów

Najnowsze instrukcje dla Maszyna efektów

Velleman

Velleman vdl660rl Instrukcja

10 Października 2024
Valcom

Valcom V-5580041A Instrukcja

8 Października 2024
Magmatic

Magmatic PMDMX1 Instrukcja

8 Października 2024
Magmatic

Magmatic CRISP Instrukcja

8 Października 2024
Magmatic

Magmatic CRISP MAX Instrukcja

8 Października 2024
Magmatic

Magmatic SIDEWINDER Instrukcja

8 Października 2024
Magmatic

Magmatic JAVELIN Instrukcja

8 Października 2024
BeamZ

BeamZ BLAZE3500 Instrukcja

8 Października 2024