Instrukcja obsługi Aiphone IX-MV

Aiphone Interkom IX-MV

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Aiphone IX-MV (12 stron) w kategorii Interkom. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/12

1. Aiphone assumes no responsibility for damages as a result of delayed or unusable services, which were

due to failures in network equipment, communication services by Internet and cellular phone companies, line

interruptions, communication failures, or inaccuracies or omissions in the transmission unit.

2. We will under no conditions be liable for damage that occurs due to the inability to communicate due to

malfunctions, problems, or operational errors in this product.

3. If personal information leaked by eavesdropping or unauthorized access in the communication paths over

the Internet, please be aware that Aiphone assumes no responsibility for the damages.

4. We will under no conditions be liable for any damages or losses resulting from this product’s contents or

speciﬁ cations.

without prior permission from Aiphone Co., Ltd. is strictly forbidden.

6. Please note that this manual may be revised or changed without prior notice.

7. Please note that product speciﬁ cations may be changed for the sake of improvement without prior notice.

8. Please be aware that it is the customer’s responsibility to ensure that their computer is secure. We will under

no conditions be liable for security failures.

9. This system is not intended for life support or crime prevention. It is just a supplementary means of

conveying information. Aiphone will under no conditions be liable for loss of life or property which occurs

while the system is being operated.

10. Keep the unit more than 1m (3.3’) away from radio or TV set.

11. Install the unit in an area that will be accessible for future inspections, repairs, and maintenance.

12. As to other manufacturer’s devices (such as sensor, detectors, door releases) used with this system, comply

with the Speciﬁ cations and Warranty conditions that the manufacturers or venders present.

13. If the unit is down or does not operate properly, unplug the power supply or turn off the POWER switches.

14. If it is used close to a cellular phone, the unit may malfunction.

15. The unit can be damaged if dropped. Handle with care.

16. The unit turns inoperative during power failure.

17. In areas where broadcasting station antennas are close by, the intercom system may be affected by radio

frequency interference.

18. All the units, except for door station, is designed for indoor use only. Do not use outdoor.

19. This product, being a control unit of door release, should not be used as a crime prevention device.

20. It must be noted in advance that the LCD panel, though manufactured with very high precision techniques,

inevitably will have a very small portion of its picture elements always lit or not lit at all. This is not

considered a unit malfunction.

21. At a gate or porch illuminated by a ﬂ uorescent lamp, the picture may vary, but this is not a malfunction.

22. If stripes or ﬁ ne patterns are reﬂ ected, outlines and colors shown may differ from actual people or

backgrounds, but this is not a malfunction.

23. Warm-color lighting shining on the video door station may change the tint of the picture on the monitor.

24. When using ﬂ uorescent lights to illuminate the screen its colors may periodically change (color rolling), but

this is not a malfunction.

25. The unit case may become a warm with use, but this is not a unit malfunction.

Handset

Hook switch

Speaker

Keypad

MONITOR

button

TALK button / Talk indicator (blue)

OFF button

Microphone

SPEED DIAL Buttons (x6)

PRIVACY button / Privacy indicator (blue)

TRANSFER button / Transfer indicator (orange)

RESET button (beneath the signature plate)

LIST button / List indicator (blue)

SETTINGS button / Settings indicator (blue)

Select button

ADJUST button

Up/Down and L/R buttons

Door Release button

Color LCD monitor Status indicator (orange/blue) Back

CAT5e/6 cable connections

Low voltage cable connections

MAC address

Press and hold the reset button for

longer than 1 second, then release to

restart station.

Accessories included

Installation Manual

(this manual)

Quick Start Programming Guide

(English) x1

Chinese RoHS paper

DVD-ROM

(Support Tool, Manuals,

Custom Sound (sample)) x1

Mounting bracket

screw x4

Desk stand

Cable tie

Signature card*1

Signature plate*1

Wall mounting

screws x4

*1 Attached to the main unit.

Desk stand

screws x4

Mounting bracket*1

Precautions

ecautions

ecautionsPrecautions

• Read this manual before installation and connection.

Read the "Setting Manual" and "Operation Manual" included on the DVD-ROM.

• Conﬁ gure the system settings according to the "Setting Manual" after completing the installation

and connection. The system will not function unless it has been properly conﬁ gured.

• After installation, explain to the customer how to use the device, and be sure to provide the

accompanying DVD-ROM.

Important

• Perform the installation and connection only after fully understanding this device and the manual.

Illustrations used in this manual may be different from the actual ones.

LAN

PoE-enabled switch

(third party)

IX Support Tool

(included with IX-MV)

(

third party

)

PoE-enabled switch

(third party)

PoE-enabled switch

(third party)

IX-BAIX-DA

IX-MV Network Video

Recorder

(third party)

Network Camera

(third party)

EMERGENCY

PoE-enabled switch

(third party)

PoE-enabled switch

(third party)

IX-DF-HID *1

IX-DF-P*2

IX-DF

PoE-enabled switch

(third party)

IX-DF-2RA*1

Warning

1. Voltage is applied to parts within the

equipment. Do not touch any parts that are

not associated with the installation, wiring,

or connection. Electric shock could result.

Dismantling

alteration

2. Do not dismantle or alter the unit.

Fire or electric shock could result.

3. Keep the unit away from water or any

other liquid.

Fire or electric shock could result.

4. The unit is not explosion-proof. Do not

install or use near gases or ﬂ ammable

materials.

Fire or explosion could result.

5. Do not connect any terminal on the unit

to an AC power line.

Fire or electric shock could result.

6. Do not put any metal or ﬂ ammable

material into the unit through the

openings.

Fire, electric shock, or unit trouble could

result.

7. Existing wiring such as chime wiring,

etc. may contain high voltage AC

electricity. Damage to the unit or

electric shock could result. Wiring

and installation should be done by a

qualiﬁ ed technician.

Negligence could result in .death or serious injury

Caution

Negligence could result in .injury to people or damage to property

1. Do not install or make any wire

terminations while power supply is

plugged in. It can cause electrical shock

or damage to the unit.

2. Before turning on power, make sure

wires are not crossed or shorted. If not,

ﬁ re or electric shock could result.

3. Do not install the unit in any of the

following locations. Fire, electric shock,

or unit trouble could result.

• Places under direct sunlight or places

near heating equipment that varies in

temperature.

• Places subject to dust, oil, chemicals,

hydrogen sulﬁ de (hot spring).

• Places subject to moisture and

humidity extremes, such as

bathrooms, cellars, greenhouses, etc.

• Places where the temperature is quite

low, such as inside a refrigerated area

or in front of an air conditioner.

• Places subject to steam or smoke (near

heating or cooking surfaces).

• Where noise generating devices

such as dimmer switches or inverter

electrical appliances are close by.

• Locations subject to extremely

powerful electric ﬁ elds.

4. When mounting the unit on a wall,

install the unit in a convenient location,

but not where it could be jarred or

bumped. Injury could result.

5. Do not place or install the unit in the

locations subject to frequent vibration or

impact. If the unit falls, injury to people

or damage to the unit could result.

6. Do not run wires between movable

objects (doors, windows, etc.). It may

cause malfunction.

7. Do not press on the LCD or subject it to

a high impact. The LCD glass could be

punctured and result in an injury.

8. If the LCD is punctured, do not allow

skin contact with the liquid crystal

inside. Inﬂ ammation could result.

* If liquid crystal is ingested,

immediately gargle with water and

seek medical attention.

* If contact with the eyes or skin

occurs, clean with pure water for at

least 15 minutes and seek medical

attention.

9. Do not put anything on the unit or cover

the unit with cloth, etc. Fire or unit

trouble could result.

10. Be sure to perform a call test or check

the chime volume with the handset on

the hook. If you operate the hook switch

with the handset on your ear, a sudden

call etc. may arrive causing damage to

your ear.

Notice

Installation Manual IX-MV (Master Station)

Example of

Example of System Con

System Con

System Conﬁ

ﬁ

gur

gura

ation

tion

tionExample of System Conﬁ guration

Par

art Names and Accessories

t Names and Accessories

t Names and AccessoriesPart Names and Accessories

Intr

Introduction

oduction

oductionIntroduction

Indica

Indicator

tor

tors

sIndicators

Refer to the separate "IX-MV Operation Manual" for indicators other than those listed.

Light ON

Light OFF

Name Status (Pattern)

Explanation

Status

indicator

Orange

ﬂ ashing

Normal ﬂ ashing

0.75 sec 0.75 sec

Booting

Fast ﬂ ashing

0.25 sec 0.25 sec

Device

error

Long interval ﬂ ashing

0.5 sec 4 sec

Communication

failure

Long irregular ﬂ ashing

1 sec 0.25 sec 0.25 sec0.25 sec 0.25 sec 0.25 sec

Firmware

version

upgrading

Short irregular ﬂ ashing

1 sec 0.25 sec0.25 sec 0.25 sec

Initializing

Blue

light

During

communication,

Standby

(Depends on

setting)

Issue Date : Nov. 2014 FK2121 A P1114 SQ 56145 Printed in Thailand

Number of station registrations in address book

Product number Product name

Number of station registrations

in address book

IX-MV Master Station 500 stations

IX-DA, IX-DF, IX-DF-HID-I*1, IX-DF-HID*1,

IX-DF-2RA*1, IX-DF-PI*2, IX-DF-P*2

Video Door Station 20 stations*

IX-BA, IX-SS, IX-SS-2RA*1

Audio Only Door Station

20 stations*3

*1 North America only.

*2 Except North America. HID Card Reader is not included.

*3 Only Master Stations can be registered (Max. 20).

Installation of Master Station

Mounting height

(box center)

1,500 mm (5')

Main unit

Signature plate p2-x1 (included*

Signature card p2-x1 (included*

CAT5e/6 cable

Attach the main unit to the

mounting bracket.

3-gang box

Mounting bracket

(attached to the back of the main unit.)

Low voltage cable Mounting bracket screws (included) x4

Attach the mounting bracket to

the wall.

Fill in name on signature card

(1) Remove the transparent signature plate

while pressing the top or bottom of the

plate.

*Remove the signature card.

(2) Fill in the registered station names onto

the white part of the signature card.

(3) Reattach the signature plate.

*1: The signature plate and signature card

are attached before shipment. Connect the CAT5e/6 cable and low voltage cable to the main unit.

Wall Mounting

83.5 mm (3-5/16")

92 mm (3-5/8")

Mounting height

(equipment center)

1,500 mm (5')

Point

The supplied screws cannot be used on plaster or concrete

walls, please use anchors or concrete plugs (both are locally

available products).

Main unit

Wall mounting screws (included) x4

Connect the CAT5e/6 cable

and low voltage cable to the

main unit, wiring as shown in

the figure.

Mounting bracket

Surface wiring

Connect the CAT5e/6 cable and

low voltage cable to the main unit.

Assemble the Desk stand.

* Set the Desk stand on a flat surface to keep it stable.

If necessary, secure the Desk stand.

* The Desk stand can be adjusted in 3 angles. Fit the

legs into the grooves of the desired angle.

Attach the mounting

bracket to the Desk

stand.

Attach the main

unit to the

mounting bracket.

CAT5e/6 cable

Mounting

bracket

Desk stand

(included)

Weak current line

Desk stand screws p2-x4 (included)

Point

•

Insert the Desk stand screws into the mounting bracket screw holes, then attach the mounting bracket to the Desk stand tightly.

• If necessary, secure the CAT5e/6 cable or low voltage cable using the included cable tie.

• When using the Desktop mounting, use the included Desk stand.

2 14

Main unit

30°

45°

60°

LegUnit



If mounting on the Desk stand

Connection Precautions

Cable

The cable is not included with the product.

CAT5e/6 cable

• Use a straight cable when connecting between equipment.

• Do not use a CAT5e/6 cable with a bending angle of less than a

25 mm (1”) radius. A radius of less than 25 mm (1”) could cause a

communication failure.

CAT5e/6 cableCAT5e/6 cable

Radius ≥ 25 mm (1") Radius < 25 mm (1")

• Do not peel the jacket off the CAT5e/6 cable any more than is

necessary.

• Attach the RJ45 modular plugs using either EIA/TIA-568A or 568B.

Pair4

Pair3

Pair2

Pair1

T568A

Pair4

Pair2

Pair3

Pair1

T568B

1 2 3 4 5 6 7 81 2 3 4 5 6 7 8

• Use the LAN tester to conﬁ rm conduction before connecting the

CAT5e/6 cable.

• The RJ45 connector with cover cannot be connected to CAT5e/6 cable

terminals for Master Station or Door Stations. Use cables without covers

on the connectors.

• Do not pull the CAT5e/6 cable or apply excessive load.

Cable precautions

• Do not use separate conductors, twisted pair cables, or coaxial cables.

• Do not use an odd number cable.

How to attach and remove a low voltage cable

• Insert into the quick connection terminal.

• If it is difﬁ cult to insert the wire, hold down the disconnect button while

inserting the wire.

Example: Back of the IX-MV

Remove

button

8 mm(3/8")

Wiring Connection

LAN/PoE

10BASE-T

100BASE-TX

CAT5e/6 straight (UTP)

Relay output

Contact Input*2

PoE-enabled switch

100 m (330')

ϕ0.8mm(20AWG)-2C

IX-MV

Master Station

ϕ0.8mm(20AWG)-2C

Polarized

*1 Relay Output Speciﬁ cations

Output

method

Normally open dry contact

Voltage

between the

terminals

AC 24V, 0.5A (resistive load)

DC 24V, 0.5A (resistive load)

Minimum load (AC/DC): 100 mV, 0.1 mA

*2 Contact Input Speciﬁ cations

Input

method

Form C dry contact (N/O or N/C)

Level detection method

Fixed

detection

time

200 msec or more

Contact

resistance

Maximum closure resistance: 700 or lessΩ

Minimum open resistance: 3 k or moreΩ

Terminal

short-circuit

current

10 mA or less

Voltage

between the

terminals

DC5 V or less

(between open terminals)

How to Install

w to Install

w to InstallHow to Install Ho

How to Connect

w to Connect

w to ConnectHow to Connect

Specyfikacje produktu

Marka:	Aiphone
Kategoria:	Interkom
Model:	IX-MV

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Aiphone IX-MV, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Interkom Aiphone

Aiphone LEF-10 Instrukcja

27 Września 2024

Aiphone TD-3H/B Instrukcja

22 Września 2024

Aiphone IX-MV Instrukcja

16 Września 2024

Aiphone JP-DV Instrukcja

12 Września 2024

Aiphone LE-DA Instrukcja

11 Września 2024

Aiphone DBS-1A Instrukcja

8 Września 2024

Aiphone TD-12H/B Instrukcja

5 Września 2024

Aiphone JOS-1F Instrukcja

5 Września 2024

Aiphone JPS-4AEDV Instrukcja

30 Sierpnia 2024

Aiphone GT-1A Instrukcja

22 Sierpnia 2024

Instrukcje Interkom

Najnowsze instrukcje dla Interkom

Viking K-1900-712L-EWP Instrukcja

9 Października 2024

Viking K-1700-3 Instrukcja

9 Października 2024

Viking E-50-SS Instrukcja

9 Października 2024

Viking E-50-WH Instrukcja

9 Października 2024

Viking K-1700-IP-EWP Instrukcja

9 Października 2024

Viking E-60-BN Instrukcja

9 Października 2024

Viking E-1600-53-IP Instrukcja

9 Października 2024

Viking E-60-WH Instrukcja

9 Października 2024

Viking K-1900-8-IP-EWP Instrukcja

9 Października 2024

Viking W-2000A Instrukcja

9 Października 2024