Instrukcja obsługi AFX Vaportite VTL476000LAJD2
AFX
Verlichting
Vaportite VTL476000LAJD2
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AFX Vaportite VTL476000LAJD2 (2 stron) w kategorii Verlichting. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
Model #: VTL243500LAJD2
VTL476000LAJD2
LED Outdoor Luminaires
Ceiling Mount - Vapor Tight
120 277 - VAC / 60Hz
Page 1 of 2 8061547 R0
Safety Precautions
Read all safety precautions and installation instructions carefully before installing or servicing this xture. Failure to comply with these instructions could result in potentially
fatal electric shock and/or property damage.
It is recommended that a qualied electrician perform all wiring. This xture must be wired in accordance with all national and local electrical codes.
Do not handle any energized xture or attempt to energize any xture with wet hands or while standing on a wet or damp surface or in water.
This xture is designed for use in a 120-277VAC, 60Hz fused circuit. This xture is compatible with 0-10V dimming circuit.
To reduce the risk of electrical shock, and to assure proper operation, this xture must be adequately grounded. To accomplish proper grounding, there must be a separate
ground wire (green) contact between this xture and the ground connection of your main power supply panel.
This xture is intended to be used for general door lighting in dry, damp or wet locations. For wet locations, xture must be mounted at least 48 inches above ground out
level.
Disclaimer
Changes or modications not expressly approved by the party responsible for compliance could void NOTE: This equipment the user’s authority to operate the equipment.
has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian ICES-005 (B) / NMB-005 (B). These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiver antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult with the dealer or an experienced radio/TV technician for help.
Any modications to this xture may void the warranty and interfere with the safe operation of the luminaire.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Assembly Instructions
Step 1 Preparing for installation–
A. at fuse or circuit Disconnect electrical power
breaker box before installing or servicing any part
of this xture.
B. Carefully remove the LED xture from the carton.
C. Release the diuser (2) from the xture (1) by
unlatching all mechanical latches. Diuser is
tethered to the latch on both ends.
D. lip Release LED plate assembly (6) from c
brackets. LED plate is tethered to housing (1).
E. Identify location of mounting brackets on xture
relative to power source. Holes are supplied for
power connection at end or through the top. Fitting
is supplied for cord connection If top is used for .
connection, remove knockout and install plastic
cap (6) onto the front end for water tight seal.
F. set of replacement plastic latches are provided if A
factory install metal latches (8 are not desirable. ed )
Pull on the latch to unsnap it from the groove. To
install snap new latch by aligning pin onto the
receiving groove in reverse order of removal.
Step Mounting fixture 2 –
A. Select location for mounting the xture. Two
brackets (3) are supplied with drywall anchors &
screws (4) & (5 Follow drilling dimension for ).
brackets spacing for 48” or 24” fixture.
B. To locate, hold xture assembly up to ceiling with
power supply hole located over entryway for power
supply wires. Mark the locations of the mounting holes for brackets (3 on the ceiling. )
C. Take the xture down and punch a small hole into the ceiling at each location using a nail or awl to see if there is a wood joist. Attach to surface using fasteners and
sealing washers (not provided) appropriate to ceiling materials.
D. If there is a joist, use a suitable wood screw (4) to mount the xture housing. Where there is no joist to screw into, use drywall anchors (4) & (5) or toggle bolts (not
provided) of suitable length to mount housing securely to the ceiling.
E. Mount the xture with appropriate fasteners while passing the supply wires into the opening of the housing.
Wiring All wiring must take place inside junction box (not included) –
Caution: Note: Make sure power is o at fuse or circuit breaker box. Check power wires for damage or scrapes. Use wire suitable for at least °C (194°F). 90 Most dwellings
built before 1985 have supply wire rated to 60C. Consult a qualied electrician ensure correct branch circuit conductor before installing.
Step 3 Wiring fixture –
A. Make all wire connections to appropriate wire. Secure with wire nut and power connectors (supplied).
B. Strip o 1/2" insulation to expose bare wires on supply power source black (L) and white (N).
C. Connect the green wire from the xture to the supply power source ground wire.
D. Connect the black wire from the xture to the black (L) wire from supply power source. Connect the white wire from the xture to the For none dimming xture.
white (N) wire from supply power source. Pink and purple wires are not to be used and must be individually capped to prevent shorting.
E. . Connect the pink wire from the xture to the dimmer source gray wire. Connect the purple wire from the xture to the dimmer source For (0-10V) dimming xture
purple wire. Connect the white wire from the xture to the neutral (N) wire from dimming source per dimmer wiring instructions. Connect the black wire from the xture
to the control line (L) wire from dimmer supply power source per dimmer wiring instructions.
Model #: VTL243500LAJD2
VTL476000LAJD2
LED Outdoor Luminaires
Ceiling Mount - Vapor Tight
120 277 - VAC / 60Hz
Page 2 of 2 8061547 R0
Limited Factory Warranty
AFX warrants this xture is free from defects in materials and workmanship when installed and used under normal operating conditions for a period of 5 years from date of
purchase. This warranty covers all component parts and extends only to replacement of defective xture or components; it does not cover failure due to improper installation,
misuse, mishandling or damage incurred in transit.
F. Do not mix wires. Pull on each wire lead to make sure connections are secure. Make certain no bare wires are exposed outside of wire connectors.
G. -install LED plate to the clip brackets in the housing (1). Re
Step 4 Color changing temperature adjustment, CCT (if desired) –
A. Adjust CCT switch according to the desired color temperature as shown below. Note: Fixture is preset to 3000K from factory.
Step 5 Diuser installation –
A. Install diuser (2) onto housing by securing latches, rotating/alternating around edge of housing and capturing diuser with rounded lip. Snap latches closed. Twelve
latches for 48” and six for 24” version.
Step 6 store power at fuse or circuit breaker box– Re
Specyfikacje produktu
Marka: | AFX |
Kategoria: | Verlichting |
Model: | Vaportite VTL476000LAJD2 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z AFX Vaportite VTL476000LAJD2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Verlichting AFX
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
Instrukcje Verlichting
- Verlichting Ikea
- Verlichting Tesy
- Verlichting LG
- Verlichting BeamZ
- Verlichting TP-Link
- Verlichting Milwaukee
- Verlichting Philips
- Verlichting Toolcraft
- Verlichting Conceptronic
- Verlichting Theben
- Verlichting Mio
- Verlichting Behringer
- Verlichting Nedis
- Verlichting Be Cool
- Verlichting American DJ
- Verlichting OK
- Verlichting Toshiba
- Verlichting Fenix
- Verlichting Hazet
- Verlichting Ardes
- Verlichting Gardena
- Verlichting DeWalt
- Verlichting Sigma
- Verlichting Honeywell
- Verlichting Chauvet
- Verlichting Steinel
- Verlichting Makita
- Verlichting Dyson
- Verlichting Vintec
- Verlichting RYOBI
- Verlichting Godox
- Verlichting Chamberlain
- Verlichting Trust
- Verlichting IFM
- Verlichting Biltema
- Verlichting V-TAC
- Verlichting Schneider
- Verlichting Eurolite
- Verlichting Emos
- Verlichting Crivit
- Verlichting Osram
- Verlichting Perel
- Verlichting Ansmann
- Verlichting DiO
- Verlichting Velleman
- Verlichting Delta Dore
- Verlichting Nordlux
- Verlichting Monster
- Verlichting Showtec
- Verlichting Lenoxx
- Verlichting EtiamPro
- Verlichting Ibiza Sound
- Verlichting ION
- Verlichting Maginon
- Verlichting Brilliant
- Verlichting Brandson
- Verlichting Rocktrail
- Verlichting Novy
- Verlichting Innoliving
- Verlichting Omnitronic
- Verlichting Livarno Lux
- Verlichting Elro
- Verlichting Hama
- Verlichting Busch + Müller
- Verlichting Cameo
- Verlichting Goobay
- Verlichting COLBOR
- Verlichting Elation
- Verlichting GVM
- Verlichting Infinity
- Verlichting Denver
- Verlichting Blumfeldt
- Verlichting Intellytech
- Verlichting Nitecore
- Verlichting SereneLife
- Verlichting Olight
- Verlichting Black Diamond
- Verlichting Martin
- Verlichting Vivanco
- Verlichting PowerPlus
- Verlichting HiKOKI
- Verlichting Workzone
- Verlichting Ikan
- Verlichting Kathrein
- Verlichting Impact
- Verlichting Monacor
- Verlichting Aputure
- Verlichting HQ Power
- Verlichting Dörr
- Verlichting Karma
- Verlichting Smartwares
- Verlichting Magmatic
- Verlichting Metabo
- Verlichting Adj
- Verlichting Varaluz
- Verlichting ETC
- Verlichting Cotech
- Verlichting Gre
- Verlichting Stairville
- Verlichting XQ-lite
- Verlichting Perfect Christmans
- Verlichting Profoto
- Verlichting Rosco
- Verlichting Light4Me
- Verlichting Reflecta
- Verlichting Qazqa
- Verlichting Tel Sell
- Verlichting Brennenstuhl
- Verlichting KonstSmide
- Verlichting LivarnoLux
- Verlichting Tiger
- Verlichting Eglo
- Verlichting Lucide
- Verlichting Caliber
- Verlichting Kichler
- Verlichting Sun Joe
- Verlichting GLP
- Verlichting Megaman
- Verlichting GlobalTronics
- Verlichting Steren
- Verlichting Livarno
- Verlichting Watshome
- Verlichting Melinera
- Verlichting In Lite
- Verlichting Maul
- Verlichting Näve
- Verlichting Chacon
- Verlichting Astro
- Verlichting Bigben
- Verlichting Massive
- Verlichting Yongnuo
- Verlichting Gamma
- Verlichting Lexon
- Verlichting Steinhauer
- Verlichting QTX
- Verlichting HQ
- Verlichting Max
- Verlichting Nanlite
- Verlichting Ranex
- Verlichting Paul Neuhaus
- Verlichting REV
- Verlichting Dymond
- Verlichting Friedland
- Verlichting Nexxt
- Verlichting Neewer
- Verlichting Artecta
- Verlichting Litepanels
- Verlichting Litecraft
- Verlichting Garden Lights
- Verlichting Manfrotto
- Verlichting Shada
- Verlichting Swisstone
- Verlichting KS
- Verlichting Dydell
- Verlichting Aqara
- Verlichting Botex
- Verlichting Levita
- Verlichting Paulmann
- Verlichting Heirt
- Verlichting Kogan
- Verlichting LYYT
- Verlichting Wetelux
- Verlichting Aqua Signal
- Verlichting Century
- Verlichting Esotec
- Verlichting Lideka
- Verlichting Obsidian
- Verlichting Lutec
- Verlichting FlinQ
- Verlichting IXL
- Verlichting Fun Generation
- Verlichting Meipos
- Verlichting Beghelli
- Verlichting EXO
- Verlichting Mellert SLT
- Verlichting 4K5
- Verlichting Wireless Solution
- Verlichting LightZone
- Verlichting Varytec
- Verlichting Canarm
- Verlichting GP
- Verlichting Luxform
- Verlichting Karwei
- Verlichting Blumill
- Verlichting Delock Lighting
- Verlichting LightPro
- Verlichting CIVILIGHT
- Verlichting Gingko
- Verlichting Outspot
- Verlichting Raya
- Verlichting Chrome-Q
- Verlichting Maxim
- Verlichting Megatron
- Verlichting MeLiTec
- Verlichting Integral LED
- Verlichting Casalux
- Verlichting Briloner
- Verlichting Dainolite
- Verlichting GEV
- Verlichting Kinotehnik
- Verlichting Litegear
- Verlichting HERA
- Verlichting Astera
- Verlichting Temde
- Verlichting Aveo Engineering
- Verlichting AD Trend
- Verlichting Prolycht
- Verlichting DeSisti
- Verlichting Cineo
- Verlichting Zylight
- Verlichting Smith-Victor
- Verlichting Light & Motion
- Verlichting ET2
- Verlichting Quoizel
- Verlichting Golden Lighting
- Verlichting Weeylite
- Verlichting Crystorama
- Verlichting Valerie Objects
Najnowsze instrukcje dla Verlichting
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024