Instrukcja obsługi A-NeuVideo ANI-42HPIPX

A-NeuVideo router ANI-42HPIPX

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla A-NeuVideo ANI-42HPIPX (36 stron) w kategorii router. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/36
ANI-42HPIPX
UHD+ 4x2 HDMI Matrix with PiP
A-NeuVideo.com
Frisco, Texas 75036
INSTRUCTION MANUAL
PACKAGE CONTENTS
Before attempting to use this unit, please check the packaging and make sure the following items are
contained in the box:
ANI-42HPIPX UHD+ 4x2 HDMI Matrix with PiP
24V/2.7A DC Power Adapter
Rackmount Ears (Set of 2)
Shockproof Feet (Set of 4)
SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power o󰀨 and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualied service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualied service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.
TABLE OF CONTENTS
A NEUVIDEO
1
CONTENTS
INTRODUCTION ..........................................................................1
FEATURES / APPLICATIONS / SYSTEM REQUIREMENTS ....2
SPECIFICATIONS / CABLE SPECIFICATIONS ........................3
OPERATION CONTROLS & FUNCTIONS ...............................4
FRONT PANEL ...................................................................4
REAR PANEL .....................................................................5
RS-232 CONTROL / TELNET CONTROL ...................................6
OSD MENU ................................................................................14
WEBGUI CONTROL .................................................................23
CONNECTION DIAGRAM .......................................................29
VIDEO SPECIFICATIONS ........................................................30
AUDIO SPECIFICATIONS ........................................................31
Dear Customer
Thank you for purchasing this product. For optimum performance
and safety, please read these instructions carefully before
connecting, operating or adjusting this product. Please keep this
manual for future reference.
INTRODUCTION
The ANI-42HPIPX This 4x2 HDMI Matrix with PiP is a high
performance HDMI switch with integrated scaling and multi-
windowing technology which can connect up to (4) 4K UHD+ HDMI
sources to up to (2) 4K UHD+ HDMI displays and freely switch
between them. It is an ideal solution for monitoring or displaying
multiple sources simultaneously for use in control rooms, conference
rooms or classrooms. Video resolutions up to 4K@60Hz and LPCM
audio up to 7.1 channels at 192KHz are supported and this unit is
fully compatible with the HDCP 1.x and 2.2 standards.
Any of (4) di󰀨erent HDMI sources may be displayed individually,
full screen, with seamless switching in Matrix mode, or they can be
displayed using a variety of multi-window modes including standard
views like PiP (Picture in Picture) and PoP (Picture outside of
Picture) as well as fully customizable quad-window modes. Control
of input/window routing, position and sizing is easy using the front
panel controls with OSD menu as well as by WebGUI, RS-232, and
Telnet. This product has a 3 year warranty.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
Always follow basic safety precautions to reduce the risk of re,
electrical shock and injury to persons.
• To prevent re or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
su󰀩cient space for air to circulate around the unit.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update or
to keep current the information contained in this document.
We reserve the right to make improvements to this document and/
or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer le, in any form or by any means
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise — without the express written permission and consent.
© Copyright 2022. All Rights Reserved.
Version 1.2 JULY 2022
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.


Specyfikacje produktu

Marka: A-NeuVideo
Kategoria: router
Model: ANI-42HPIPX

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z A-NeuVideo ANI-42HPIPX, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje router A-NeuVideo

A-NeuVideo

A-NeuVideo ANI-42HPIPX Instrukcja

2 Października 2024
A-NeuVideo

A-NeuVideo ANI-44HPSC Instrukcja

2 Października 2024
A-NeuVideo

A-NeuVideo ANI-9-MV Instrukcja

2 Października 2024
A-NeuVideo

A-NeuVideo ANI-42HPIP Instrukcja

2 Października 2024
A-NeuVideo

A-NeuVideo ANI-28UHDDA Instrukcja

2 Października 2024
A-NeuVideo

A-NeuVideo ANI-8X2MFS Instrukcja

2 Października 2024
A-NeuVideo

A-NeuVideo ANI-16-MV Instrukcja

2 Października 2024
A-NeuVideo

A-NeuVideo ANI-88HDRH Instrukcja

2 Października 2024

Instrukcje router

Najnowsze instrukcje dla router