Instrukcja obsługi A-Designs REDDI

A-Designs Niesklasyfikowane REDDI

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla A-Designs REDDI (8 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
REDDI™
Owner’s Manual
LEGAL
NOTICE:
Fill out and Return Warranty Card to A Designs Audio, Inc. Warranty begins the day of purchase. Your name will be
placed on our mailing list (unless otherwise requested) for future updates and new product announcements.
A Designs Audio, Inc. reserves the right to make improvements or changes at any time to this product.
Published by: A Designs Audio, Inc.
P.O. Box 4255, West Hills, CA 91304 U.S.A.
Edition 1.0 2002
Copyright 2013 A Designs Audio
All Rights Reserved.
One Year Limited Warranty Internal Parts, 30-Day Limited Warranty Labor, 30-Day Limited Warranty Tubes.
Warranty will be void if product has been opened by unauthorized personnel or enduser. A Designs Audio, Inc. warrants
that our hardware conforms substantially to the specifications contained in this manual when used in accordance these
specifications for a period of one year from the date of original purchase from A Designs or its authorized dealers. In
case of a valid warranty claim, your sole and exclusive remedy and A Designs’ entire liability under any theory of liability
will be, at its option, to repair or replace the product without charge, or, if not possible, to refund the purchase price to
you. The warranty is not transferable and applies only to the original purchaser of the product.
For warranty service, contact A Designs Audio, Inc. at 818-716-4153 to obtain a Return Merchandise Authorization (RMA)
number. After obtaining the RMA number, ship defective product to A Designs Audio, Inc., P.O. Box 4255, West Hills, CA
91304. Write RMA number on outside of shipping box. Be sure to include your name, address, phone number, copy of
original sales invoice and detailed description of the problem. A Designs Audio will not accept responsibility for loss or
damage in shipping.
Warranty is void if product serial numbers have been removed or if the product has been damaged by abuse or
unauthorized modification and repair. There are no user serviceable parts inside.
THIS WARRANTY IS IN LIEU OF ALL WARRANTIES WHETHER ORAL OR WRITTEN, EXPRESSED OR IMPLIED.
A DESIGNS AUDIO, INC. MAKES NO OTHER WARRANTY EITHER EXPRESSED OR IMPLIED, INCLUDING
WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, UNLESS FOR A PARTICULAR
PURPOSE OR NONINFRINGEMENT. PURCHASERS SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY SHALL BE REPAIR OR REPLACEMENT AS SPECIFIED HEREIN.
IN NO EVENT WILL A DESIGNS AUDIO, INC. BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCREMENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM ANY DEFECT IN THE PRODUCT, INCLUDING LOST PROFITS,
DAMAGE TO PROPERTY AND, TO THE EXTENT PERMITTED BY LAW, DAMAGE FOR PERSONAL INJURY, EVEN IF
A DESIGNS AUDIO, INC. HAS BEEN ADVISED OF THE POSSIBILITIES OF SUCH DAMAGES.
A Designs, A Designs Audio, and REDDI are trademarks of A Designs Audio, Inc. All other trademarks are the
property of their respective owners.
Introduction
Owner’s Manual
|
3REDDI
™
Welcome to the Analog Sound of the REDDI. This is an all tube product, and there are some basics you should know before
using for the first time.
Tubes are a component that have specialized and unique features. If you are a “pre” or baby boomer, born before 1957,
you may recall using tubes in various products, such as radios, amplifiers, and televisions. So, this is just to refresh your
memory. If you are a “post” baby boomer, this could be your first experience with tubes, so please pay close attention!
(You will be tested at the end of this manual).
Tubes are most efficient and effective when “warmed up.” This means, upon starting the REDDI, you should allow the
tubes to become fully heated before attempting to operate. The minimum amount of warm up time is approximately five
minutes.
Set up your instrumentation layout before powering up the REDDI. Plug in your instrument while the unit is off. This will
prevent unwanted noise such as “pops.” The same applies while you shut down. Allow a minimum of 15 seconds for the
power to drain from the tubes properly. Then you can unplug your instrument.
Properly ventilate to avoid overheating! Too much heat will reduce the life-span of your tubes. A Designs Audio, Inc. has
scoured the earth for the perfect combination of tubes for this unique quality sound. Go ahead, get started. Read the
following pages carefully to become acquainted with the warmth and clarity that the REDDI can deliver to your
recordings.
Please feel free to email A Designs via the website with any creative applications for the use of the REDDI. We may just
include your suggestion on our website!
Congratulations on the purchase of your REDDI!
Most of all, have fun!
Peter Montessi, President
A Designs Audio, Inc.

Specyfikacje produktu

Marka: A-Designs
Kategoria: Niesklasyfikowane
Model: REDDI

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z A-Designs REDDI, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane A-Designs

A-Designs

A-Designs MP-2A Instrukcja

8 Października 2024
A-Designs

A-Designs REDDI Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024