Instrukcja obsługi A-Designs MP-2A

A-Designs Niesklasyfikowane MP-2A

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla A-Designs MP-2A (9 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/9
STEREO TUBE MIC PRE
MP-2A
™
Owner’s Manual
W
ARNING!
Before you start your new MP-2A Series True Tube Microphone preamp please read the following:
ANY real tube product is sensitive to a high SPL environment. This may cause microphonics in a recording situation. Make sure you are able to shock
mount and or place the unit in isolation if need be. Direct light will also affect tubes, as well.
PLEASE, be sure to have at least one rack space between any tube e and below the unit. This will products from the product abov ensure your tube unit
will not over heat. Over heating will cause damage to the tubes and shorten their life span. If possible place, the MP-2A Series unit in the top rack space
to allow air flow.
If you have received your unit via UPS/Fed-Ex/DHL, or any other courier, your MP-A should have been double boxed for protection. If it was not double
boxed, please contact your dealer and return the unit to them for a replacement.
We demand ALL our units to be double boxed to help prevent damages during shipping.
Thank you,
Peter Montessi
President
A Designs Audio, Inc.
LEGAL
NOTICE:
Fill out and Return Warranty Card to A Designs Audio, Inc. Warranty begins the day of purchase. Your name will be placed on our mailing list (unless
otherwise requested) for future updates and new product announcements.
A Designs Audio, Inc. reserves the right to make improvements or changes at any time to this product.
Published by: A Designs Audio, Inc.
P.O. Box 4255, West Hills, CA 91304 U.S.A.
Edition 4.0 2009
Copyright 2013 A Designs Audio, Inc. All Rights Reserved.
WARNING: Removing Cover Will Void Your W
arranty
.
One Year Limited Warranty Internal Parts, 30-Day Limited Warranty Labor, 30-Day Limited Warranty Tubes
A Designs Audio, Inc. warrants that our hardware conforms subs d in accordance these tantially to the specifications contained in this manual when use
specifications for a period of one year from the date of original purchase from A Designs Audio, Inc. or its authorized dealers. In case of a valid warranty
claim, your sole and exclusive remedy and A Designs’ entire liability under any theory of liability will be, at its option, to repair or replace the product
without charge, or, if not possible, to refund the purchase pr the original purchaser of the ice to you. The warranty is not transferable and applies only to
product.
For warranty service, contact A Designs Audio, Inc. at 818-716-4153 to obtain a Return Merchandise Authorization (RMA) number.
Warranty is void if product serial numbers have been removed or if the product has been damaged by abuse or unauthorized modification and repair.
There are no user serviceable parts inside.
This warranty is in lieu of all warranties whether oral or written, expressed or implied. A Designs Audio, Inc. makes no other warranty either expressed
or implied, including without limitation, any implied warranties of merchantability, unless for a particular purpose or non-infringement. The purchasers’
sole and exclusive remedy under this warranty shall be repair or replacement as specified herein.
In no event will A Designs Audio, Inc. be liable for any direct, indirect, special, incremental or consequential damages resulting from any defect in the
product, including lost profits, damage to property and, to the extent permitted by law, damage for personal injury, even if A Designs Audio, Inc. has
been advised of the possibilities of such damages.
A Designs, A Designs Audio, Inc., and MP-2A are trademarks of A Designs Audio, Inc. All other trademarks are the property of their respective owners.
Introduction
Owner’s Manual
|
3Stereo Tube Mic Pre, MP-2A
™
Welcome to the Analog Sound of the MP -2A. This is an all tube product, and there are some basics you should know before
using this product for the first time.
Tubes are a component that have specialized and unique features. If you are a “pre” or baby boomer, born before 1957,
you may recall using tubes in various products, such as radios, amplifiers, and televisions. So, this is just to refresh your
memory. If you are a “post” baby boomer, this could be your first experience with tubes, so please pay close attention!
(You will be tested at the end of this manual).
Tubes are most efficient and effective when “warmed up.” This means, upon starting the MP-2A, you should allow the
tubes to become fully heated before attempting to operate. The minimum amount of warm up time is approximately 15 to
20 minutes.
Set up your instrumentation layout before powering up the MP-2A. Plug in your instrument or microphone while the unit is
off. This will prevent unwanted noise such as “pops.” The same applies when you shut down. Allow a minimum of 25
seconds for the power to drain from the tubes properly. Then you can unplug your instrument or microphone. Always turn
your Phantom switch to the off position before plugging or un-plugging your Microphone.
When placing the MP-2A Series in a rack, we recommend using the first tier or allow one x space in order to properly
ventilate. Avoid overheating! Too much heat will reduce the life-span of your tubes. We also recommend strongly that
you observe SPL and shock mount any tube product.
A Designs Audio, Inc. has scoured the earth for the perfect combination of tubes for this unique quality sound. Go ahead,
get started. Read the following pages carefully to become acquainted with the warmth and clarity that the MP-2A can
deliver to your recordings.
Please feel free to email A Designs Audio, Inc. via the website with any creative applications for the use of the MP-2A. We
included some applications in this manual. We may just include your suggestion on our website!
Congratulations on the purchase of your MP-2A all tube microphone preamplifier! Most of all, have fun!
Peter Montessi, President
A Designs Audio, Inc.

Specyfikacje produktu

Marka: A-Designs
Kategoria: Niesklasyfikowane
Model: MP-2A

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z A-Designs MP-2A, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane A-Designs

A-Designs

A-Designs MP-2A Instrukcja

8 Października 2024
A-Designs

A-Designs REDDI Instrukcja

8 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024