Instrukcja obsługi Zebra 8585

Zebra Niesklasyfikowane 8585

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Zebra 8585 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
OVERVIEW OF THE INSTALLATION
STEPS
PREPARE/SWITCH ON 8585/8595
8585/8595 Vehicle-Mount
PREREQUISITES
Note: A description of the Config settings is detailed in the 8585/8595
User Guide, PN 8000240.
>Launch Config through Start>Programs.
>Note that Config settings can only be saved in .Admin Mode
>Enter the password .gold
>Configure the Automatic Switch-off function - this
governs the power-up and shutdown procedure for the
8585/8595 connected to a separate start up signal (for
example, a car ignition).
>Program the Front Panel keys of the 8585/8595. Assign
frequently used functions to the soft keys.
OVER >
Note: Configure the 8585/8595 before fastening it to machines or
vehicles. In this way, software configuration for the WLAN
function, for Automatic switch-off. etc. is significantly
simpler and more convenient.
>Power supply cable 1616302-001 or 1616303-001.
>If operating the 8585/8595 using an external mouse or
keyboard, connect this before switching on the device.
POWER SUPPLY/SWITCH ON THE DEVICE
>Connect the 8585/8595 to the vehicle power supply using
a 1616302-001 or 1616303-001 power cable.
>Press the Power button to switch on the 8585/8595.
IMPORTANT: The 8585/8595 series is equipped with an integrated
power supply for direct voltage. 12/24 VDC and
24/48 VDC models are available. The output
voltage of the vehicle must be compatible with the
input voltage of the 8585/8595. If it is not, the
8585/8595 may be badly damaged.
CONFIGURING THE 8585/8595
WITH CONFIG
The 8585/8595 is equipped with the configuration program, Config.
You can define the automatic switch off and front key assignment
along with other settings using this program.
IMPORTANT: Config settings should only be made by qualified
technical staff.
Config Program Functions
>Click on the Congig icon in the taskbar.
LAUNCHING CONFIG
>Config is automatically launched in the . Note Admin Mode
that Config settings can only be saved in Admin Mode.
>Enter the password . gold
Or
CONFIGURING CONTINUED
Note: Use the Settings menu to define the language of the Config
software.
WIRELESS NETWORK SETTINGS
(WLAN)
As an option, the 8585/8595 can be equipped with a Summit WLAN
card. A default WLAN profile with the basic settings is defined at the
factory. This profile must be adjusted to customer-specific require-
ments using the Summit Client Utility program (SCU).
IMPORTANT: WLAN settings with SCU should only be changed by
qualified technical staff.
>To launch SCU, click on the on the desktop.SCU icon
>Log on, and insert the password (all in uppercase).SUMMIT
>Make the necessary setting changes.
SUMMIT CLIENT UTILITY PROGRAM (SCU)
Before you mount the 8585/95:
>The automatic switch-off function must be configured.
>The installation site/vehicle must be prepared (on vehicles:
connection to ignition, observe correct voltage, etc.).
POSITION OF 8585/8595 ON VEHICLES
>The driver’s field of vision must be obstructed.not
>If a keyboard and scanner are to be installed, allow
enough space.
We recommend that the installation process be carried out in the
following sequence:
> Step 1: Secure the mounting bracket onto the vehicle.
> Step 2: Connect the cables to the device.
> Step 3: Attached the 8585/8595 to the mounting bracket.
> Step 4: If 8585/8595 is mounted above head height, it is
recommended to also use a safety strap with the
mount bracket.
Note: Copy the following web site to your browser to access product
User Guide and mounting bracket Installation Instructions:
http://www.ingenuityworking.com/knowledge/w/
knowledgebase/1135.85858595-vehicle-mount-computers-prod
uct-manuals.aspx
Ignition adaptor
cable
PN 1616302-001
Screen blanking
adaptor cable
PN 1616303-001
March 8, 2015
PN MN001636A02.a
8585/8595 VEHICLE-MOUNT COMPUTER
Quick Start Guide
M N 0 0 1 6 3 6 A 0 2
ELECTRICAL INSTALLATION
IMPORTANT!
>Position and connect the 8585/8595 as close to the battery
as possible.
>Do not attach the 8585/8595 directly to a connector for a
high-powered consumer (e.g., an inverter for forklift motors)
as this could cause restarts, malfunctions or damage to
the device.
>Some forklifts have a chassis that is connected to DC+;
therefore, the 8585/8595 chassis is also connected to DC+.
However, if peripheral devices that supply DC- to the
8585/8595 through an interconnector (such as a DC- serial
port), this will cause a short circuit. This will inevitably lead
to malfunctions or even a total system failure.
>Some forklifts have a chassis that is isolated from DC+ and
DC-. Ground connection of the 8585/85 chassis should be
connected to the vehicle chassis.
>Ensure that the ground connection is correct. Individual
vehicle requirements and any installed supplementary
electronic systems on the vehicles must be reviewed to
ensure that 8585/8595 grounding is compatible.
Refer to vehicle manufacturers instructions.
ELECTRICAL CONTINUED
Ground bolt
8585/8595 connectors,
24/48 VDC
8585/8595 connectors,
12/24 VDC
CABLE COVER AND STRAIN
RELIEF
Once the 8585/8595 and mounting bracket have been secured:
>Prepare the strain relief. (See illustration on next page.)
>Position the cables on the stress relief rail so that they will
fit through the openings in the cable cover.
>Mount the cable loosely on the strain relief rail.
Zebra reserves the right to make changes to any product to improve reliability, function, or design.
Zebra does not assume any product liability arising out of, or in connection with, the application or use of any
product, circuit, or application described herein.
No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or
patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in
which Zebra products might be used. An implied license exists only for equipment, circuit, and subsystems
contained in Zebra Products.
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty
Zebra Technologies Corporation
Lincolnshire, IL U.S.A.
http://www.zebra.com
Psion, Psion Teklogix, and the 8585/95 are trademarks of Psion Inc. Other product names mentioned in
this document are trademarks or registered trademarks of other hardware, software, or service provid-
ers and are used herein for identication purposes only.
© 2015 Psion Inc.
Final steps:
>Fix the cables to the strain relief rail.
>Close the cable cover carefully.
Example of cable positioning to the
strain relief rail

Specyfikacje produktu

Marka: Zebra
Kategoria: Niesklasyfikowane
Model: 8585

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Zebra 8585, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Zebra

Zebra

Zebra 8595 Instrukcja

9 Października 2024
Zebra

Zebra 8585 Instrukcja

9 Października 2024
Zebra

Zebra FXR90 Instrukcja

3 Października 2024
Zebra

Zebra TC27 Instrukcja

23 Września 2024
Zebra

Zebra TC22 Instrukcja

23 Września 2024
Zebra

Zebra TC58 Instrukcja

17 Września 2024
Zebra

Zebra RS6100 Instrukcja

11 Września 2024
Zebra

Zebra GS20 Instrukcja

6 Września 2024
Zebra

Zebra RE40 DKRE Instrukcja

6 Września 2024
Zebra

Zebra VS20 Instrukcja

6 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024