Instrukcja obsługi Yuneec Typhoon G
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Yuneec Typhoon G (1 stron) w kategorii Zabawki. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/1
The SteadyGrip™ is a ground handle designed to extend the GoPro® camera from
the sky to the ground, allowing you to capture amazing acon shots easier than
ever before. The camera pitch controller allows precise camera angle control on the
go using your mobile device as a display. The SteadyGrip's ergonomic design is
capable of holding up to a 6.4 inch mobile device.
The GB203 is a 3-Axis brushless self-stabilizing gimbal, compable with GoPro®
Hero 3, Hero 3+, Hero 4 Black and Hero 4 Silver, extending the use of the GoPro®
Camera to capture smooth and fluid photographs and video footage on the ground,
and amazing video footage in the sky as well.
Please take the me to read through this enre instrucon manual for more
informaon on safety, baery charging, camera controls and more before filming
your first hit video. Please also visit www.Yuneec.com for addional informaon
including product updates, bullens, videos and more.
GENERAL SAFETY PRECAUTIONS AND WARNINGS
WARNING: Failure to use this product in the intended manner as described in
instrucon manual can result in damage to the product, property and/or cause
serious injury. This product is not a toy! If misused it can cause serious bodily harm
and damage to property.
WARNING: As the user of this product you are solely and wholly responsible for
operang it in a manner that does not endanger yourself and others or result in
damage to the product or the property of others.
Always allow GB203 and SteadyGrip™ to inialize properly by seng the Steady-
Grip™ on a flat and stable surface prior to switching it on and allowing the Steady-
Grip™ and GB203 to inialize properly which somemes takes about 12 seconds.
Always operate your SteadyGrip™ in a respecul and safe manner.
FCC STATEMENT:
This equipment has been tested and found to comply with the limits for Part 15
of the FCC rules. These limits are designed to provide reasonable protecon
against harmful interference in a residenal installaon. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instrucons, may cause harmful interference to radio
communicaons.
However, there is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to radio or
television recepon, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
BATTERY WARNINGS AND USAGE GUIDELINES
WARNING: Alkaline Baeries May explode or leak, and cause burn injury if
recharged, disposed of in fire, mixed with a different baery type, inserted
backwards or disassembled. Replace all baeries at the same me. Do not carry
baeries loose in your pocket or purse. Do not remove the baery label.
WARNING: All instrucons and precauons must be read and followed exactly
and you must follow instrucons of the baery manufacturer.
INSTALLING THE AA BATTERIES
WARNING: Alkaline Baeries May explode or leak, and cause burn injury if
recharged, disposed of in fire, mixed with a different baery type, inserted
backwards or disassembled. Replace all baeries at the same me. Do not carry
baeries loose in your pocket or purse. Do not remove the baery label.
NOTICE: The use of rechargeable baeries is only recommended.
ATTACHING THE GB203 TO THE STEADYGRIP™
WARNING: Before switching on the SteadyGrip™ it is highly recommended to first
securely aach the GB203 to your SteadyGrip™.
QUICK TIP: Make sure that you have your microSD card with lots of space for
photos and videos handy.
STEP 1) Remove the protecve cover for the contactor as illustrated.
STEP 2) Carefully slide the top part of the GB203 (that also aaches below the
nose of the TYPHOON) onto the mount below the front part of the SteadyGrip™. A
corresponding ‘click’ will be noced once the GB203 has securely been installed
into the slide-in mount on the SteadyGrip™.
GoPro® COMPATIBLE DEVICES
Android:
Depending on devices
Windows Phone (8 & 8.1)²
NOTICE: Please refer to the official website of GoPro® for the latest
informaon.
WINDOWS SYSTEM
REQUIREMENTS
Windows XP (Service Pack 2 or later)
or Vista
3.2GHz Penum 4 or faster
Minimum 4GB of system RAM
MAC SYSTEM
REQUIREMENTS
Mac OS® X 10.4.11 or later
2.0GHz Intel Core Duo or faster
Minimum 4GB of system RAM
NOTICES AND WARNINGS
IMPORTANT NOTE: All safety precauons and warnings, instrucons, warranes
and other collateral informaon is subject to change at the sole discreon of
Yuneec. For the most up-to-date informaon please visit the corresponding
product page at www.Yuneec.com or contact the nearest Yuneec office or
authorized distributor.
The following special language terms are used throughout the product literature to
indicate various levels of potenal harm when operang this product:
NOTICE: Procedures, which if not properly followed, create a possibility of property
damage and/or lile to no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of
property damage and/or a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of
property damage, collateral damage and/or serious injury or create a high probability
of superficial injury.
WARNING: Read the ENTIRE instrucon manual to become familiar with the
features of the product before operang. Failure to operate the product correctly
can result in damage to the product, property and/or cause serious injury.
WARNING: This is a sophiscated consumer product. It must be operated with
cauon and common sense, and requires some basic mechanical ability. Failure to
operate this product in a safe and responsible manner could result in damage to the
product, property and/or cause serious injury. This product is not intended for use
by children without direct adult supervision. Do not use with incompable
components or alter this product in any way outside of the instrucons provided by
Yuneec. The instrucon manual contain instrucons for safety, operaon and
maintenance. It is essenal to read and follow all the instrucons and warnings
prior to assembly, setup and/or use in order to operate the product correctly and
avoid damage or serious injury.
AGE RECOMMENDATION: NOT FOR CHILDREN UNDER 14 YEARS. THIS IS NOT
A TOY.
Apple iOS:
iphone/ipad/ipod touch
OVERVIEW
SteadyGrip™ and GB203
for GoPro® Cameras
1. GB203
2. Main Status LED
3. Pitch Control Roller Wheel
4. Mode Switch Buon
5. Rubberized Ergonomic Grip
6. On/Off Switch
7. 8x AA Baery Compartment
STEP 1) Remove the Baery Cover / Door from the boom of the SteadyGrip™
Hold the boom of the SteadyGrip™ toward yourself with the front part facing
downward. Slide the baery cover / door upward with slight force and inspect the
AA baery compartment.
STEP 2) Install 8x AA Baeries
Install 8x AA Baeries as illustrated.
STEP 3) Re-installing the Baery Cover / Door on the boom of the SteadyGrip™
Once you’ve installed 8 fresh AA baeries, Hold the boom of the SteadyGrip™
toward yourself with the front part facing downward. Slide the baery cover / door
downward with slight force and ensure you hear and feel a noceable ‘click’
indicang the baery cover / door has been closed securely.
STEP 3) Powering on and inializaon. Place your
SteadyGrip™ on a flat and stable surface, then switch
on the SteadyGrip™ and it will inialize aer 12
seconds of no movement or vibraon. The LED Status
indicator on the GB203 will blink green slowly when
inializaon is completed.
GB203 LED Status:
GB203 Connecng with the SteadyGrip: LED blinking green slowly
GB203 Failing to Connect with the SteadyGrip: LED off
GB203 Connecng with the Remote Controller: LED blinking green slowly
GB203 Error: LED blinking red
CUSTOMER SERVICE
YUNEEC EU
24568 Kaltenkirchen, Germany
+49 4191 932620
eusales@yuneec.com
YUNE EC AU
53 Ellemsea Circuit, Lonsdale
South Australia 5160
+61 (0) 8 8186 3301
aussales@yuneec.com
YUNEEC USA
5555 Ontario Mills Parkway,
Ontario, CA91764, USA
1 855 2848888
sales@yuneec.com
YUNEEC HK
2/F, Man Shung Industrial Building,
7 Lai Yip Street, Kwun Tong,
Kowloon, Hong Kong
852 3616 6071
asiasales@yuneec.com
hp://yuneec.com/support
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Any informaon above might be changed due to the soware update.
For the latest documents, please check the official website.
CAMERA CONTROL
Please be sure to set photo or video mode for GoPro® Camera BEFORE installing
it into the GB203. Any operaon related to camera controls should be referred to
and downloaded according to the official website of GoPro®. GoPro® requires
APP to take photos and record videos.
NOTICE: MK58 is for long-distance real-me image transmission when installing
it on the aircra.
SWITCHING THE MODE
There are two modes of Pitch Follow Mode and Angle Mode.
Pitch Follow Mode allows the gimbal camera to track SteadyGrip in pitch
direcon. The Main Status LED indicator will be solid green.
In Angle Mode, the camera lens scks to a fixed direcon instead of following the
movement of the SteadyGrip. The user can control the Pitch Direcon through
pitch control roller wheel.
NOTICE: The default mode of SteadyGrip is Pitch Follow Mode.
To Enter Angle Mode:
Press the Mode Switch Buon on the top of the SteadyGrip to exit the Pitch
Follow mode. The Main Status LED indicator will blink GREEN. The SteadyGrip
will enter Angle Mode.
To Enter Pitch Follow Mode:
Press Mode Switch Buon again to enter Pitch Follow Mode. The Main Status
LED indicator will be solid green.
NOTE: When SteadyGrip™ is in Pitch Follow status, the gimbal camera tracks
SteadyGrip™ in pitch direcon, and the gimbal pitch control roller wheel on
SteadyGrip™ is disabled.
WARNING: procedures, which if not properly followed, create the probability of
property damage, collateral damage and serious injury or create a high probability
of superficial injury.
Failure to exercise care while using this product and comply with the following
condions and guidance could result in product malfuncon, excessive heat, fire,
property damage, and ulmately injury.
Lithium lon baeries are not toys. For the purpose of the document Li-lon, Li-Po,
Li-Fe, NiCd or NiMH baeries will be described as "Baeries".
Handling and Storage:
● Never alter, puncture or impact Baeries or related components.
● Do not directly connect the terminals with metal objects. This will short-circuit
Baeries, resulng in heat and electrical discharge.
● Never store loose Baeries together, the Baeries' terminals may contact one
another causing a short circuit.
● Never expose Baeries to extreme temperatures or direct sunlight.
● Always disconnect Baeries when not in use.
Before the First Charge:
● Ensure baeries are not damaged, as this may cause a short circuit of fire. Charging
● Always refer to your charger's manual to ensure safe operaon.
● Always charge Baeries in an open area away from flammable materials, liquids and surfaces.
● Never charge Baeries that are hot to the touch (above 120°F)
If at any me Baeries become damaged, hot, or begin to balloon or swell,
disconnue charging (or discharging) immediately. Quickly and safely disconnect
the charger. Then place the Baeries and/or charger in a safe, open area away from
flammable materials in an approved Li-Po bag to observe. Aer one hour, remove
the Baeries from service. DO NOT connue to handle, aempt to use, or ship the
Baeries. Failure to follow these procedures can cause damage to Baeries,
personal property or cause serious injury.
Damaged or swollen Baeries can be unstable and very hot. DO NOT touch
baeries unl they have cooled. Dispose of baeries in the manner required by
your city, county, state or country. Contact the appropriate Yuneec Product
Support Office to speak to a service technician for more informaon.
In the event of fire, a Class D, dry chemical fire exnguisher must be used then
baeries must be placed inside of an approved Li-Po bag.
Addional Guidelines and Warnings:
● In the event of a crash, always quickly and safely disconnect and remove Baeries
from the model. Then follow the previously listed safety procedures.
● If the internal contents of Baeries come into contact with your skin, wash the
affected area(s) with soap and water immediately. If it comes into contact with your
eye(s), flush them with generous amounts of water for 15 minutes and seek
immediately medical aenon.
• Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
This device complies with part 15 of the FCC rules. Operaon is subject to the
following two condions:
(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operaon.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protecon against harmful interference in a
residenal installaon. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruc-
ons, may cause harmful interference to radio communicaons. However, there is
no guarantee that interference will not occur in a parcular installaon. If this
equipment does cause harmful interference to radio or television recepon, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separaon between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
RF EXPOSURE WARNING
• This equipment must be installed and operated in accordance with provided
instrucons and the antenna(s) used for this transmier must be installed to
provide a separaon distance of at least 20 cm from all persons and must not be
co-located or operang in conjuncon with any other antenna or transmier.
End-users and installers must be provide with antenna installaon instrucons and
transmier operang condions for sasfying RF exposure compliance.
IC RADIATION EXPOSURE STATEMENT FOR CANADA
This device complies with Industry Canada licence-exempt RSS standard(s).
Operaon is subject to the following two condions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interfer-
ence that may cause undesired operaon of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitaon est autorisée aux deux
condions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'ulisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est suscepble d'en compromere le fonconnement.
This equipment complies with IC RSS-102 radiaon exposure limit set forth for an
uncontrolled environment.
Cet équipement respecte les limites d'exposion aux rayonnements IC définies
pour un environnement non contrôlé
ATTACHING A MOBILE DEVICE TO THE STEADYGRIP™
Step 1) Press the Curved Lip at the top
front of the SteadyGrip™ as illustrated
and fit your Mobile Device with the
screen facing toward the Main LED and
Pitch Control Wheel.
Step 2) Bind your Mobile Device to the
GoPro® camera.
The SteadyGrip™ features a camera pitch controller that allows precise camera
angle control on the go. Simply roll the pitch control wheel forward to move the
camera pitch/angle downward and roll the pitch control wheel backward to move
the camera pitch/angle upward. Please review these instrucons along with the
illustraons to familiarize yourself on how to control the GB203 and GoPro®
camera with your SteadyGrip™.
USING THE CAMERA PITCH CONTROL WHEEL
GROUND IMAGING SYSTEM
INTRODUCTION
GROUND IMAGING SYSTEM
GROUND IMAGING SYSTEM
NOTICE: The GB203 can be supplied with power through SteadyGrip™ by the Lipo
Balance Connetor Charge Lead (sold seperately) when the contact is damaged.
SteadyGrip™ LED STATUS:
Main Status LED:
Upon Powering on: Green LED blinking for twice and
then solid GREEN
Low Voltage Warning: RED LED blinking slowly
Power Cut-off: RED LED blinking quickly
Pitch Follow Funcon on: GREEN LED solid
Pitch Follow Funcon off: GREEN LED blinking
SPECIFICATIONS
STEADYGRIP™
Height: 223mm (8.78 in)
Depth (front to back): 182mm (7.17 in)
Width: 70mm (2.76 in)
Weight (without gimbal/baeries): 254g (8.96 oz)
Angle Control Range (Pitch): 30° to -90°
Runme: 240 min (depending on usage)
GB203
Dimensions: 110*80*115mm(4.33*3.15*4.53in)
Weight(without camera): 145g(5.11oz)
Pitch Control Range: 30°~-90°
Pitch Mechanical Range: 75°~-120°
Roll Mechanical Range: -45°~+45°
Yaw Mechanical Range: -45°~+45°
Compable Device: GoPro®Hero 3, Hero 3+, Hero 4 Black, Hero 4
Silver
NOTICE: If use MK58, GoPro®Hero4 Black is suggested to achieve
Specyfikacje produktu
| Marka: | Yuneec |
| Kategoria: | Zabawki |
| Model: | Typhoon G |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Yuneec Typhoon G, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Zabawki Yuneec
14 Września 2024
12 Września 2024
21 Sierpnia 2024
Instrukcje Zabawki
- Zabawki Ikea
- Zabawki Kindercraft
- Zabawki Joy-It
- Zabawki Lego
- Zabawki Berg
- Zabawki Hasbro
- Zabawki DJI
- Zabawki Chicco
- Zabawki Spin Master
- Zabawki Biltema
- Zabawki Playmobil
- Zabawki Crivit
- Zabawki Salta
- Zabawki Little Tikes
- Zabawki Chipolino
- Zabawki Velleman
- Zabawki DS
- Zabawki Hauck
- Zabawki Vtech
- Zabawki Lenoxx
- Zabawki Peg Perego
- Zabawki Parrot
- Zabawki Makeblock
- Zabawki Carrera
- Zabawki Viper
- Zabawki Kinderkraft
- Zabawki Smoby
- Zabawki Mattel
- Zabawki Jumbo
- Zabawki Kemo
- Zabawki Playtive
- Zabawki Ravensburger
- Zabawki SereneLife
- Zabawki EasyMaxx
- Zabawki BABY Born
- Zabawki Lorelli
- Zabawki Arctic
- Zabawki MJX
- Zabawki BeeWi
- Zabawki Huffy
- Zabawki Easypix
- Zabawki Sunny
- Zabawki Steren
- Zabawki King
- Zabawki Fisher Price
- Zabawki Kayoba
- Zabawki Tamiya
- Zabawki Amigo
- Zabawki X4-Tech
- Zabawki Ingo
- Zabawki Plum
- Zabawki Feber
- Zabawki Syma
- Zabawki Megableu
- Zabawki Valk
- Zabawki Wilesco
- Zabawki FABER CASTELL
- Zabawki Crayola
- Zabawki Marklin
- Zabawki Mega Bloks
- Zabawki WowWee
- Zabawki Ninetec
- Zabawki Nerf
- Zabawki KidKraft
- Zabawki Geomag
- Zabawki Bellelli
- Zabawki AXI
- Zabawki Thames & Kosmos
- Zabawki Knex
- Zabawki MNKY
- Zabawki Laptronics
- Zabawki Falk
- Zabawki Silvergear
- Zabawki Kids Knex
- Zabawki Rayline
- Zabawki Quadro
- Zabawki Pardini
- Zabawki Tiamo
- Zabawki Svexia
- Zabawki Skippy Buddy
- Zabawki Fast Rider
- Zabawki Plusbricks
- Zabawki Kogan
- Zabawki Backyard Discovery
- Zabawki Rovo Kids
- Zabawki Snap Circuits
- Zabawki Rainbow
- Zabawki Gagato
- Zabawki BIG
- Zabawki Discovery
- Zabawki Dynacraft
- Zabawki Cosco
- Zabawki Step2
- Zabawki Jamara
- Zabawki Zizzle
- Zabawki Starlyf
- Zabawki Vandermeulen
- Zabawki Merlin
- Zabawki Pure Fun
- Zabawki Dickie
- Zabawki Lidl
- Zabawki Playland
- Zabawki Hurtle
- Zabawki Jobe
- Zabawki WLtoys
- Zabawki Style Me Up
- Zabawki Bruder
- Zabawki Hudora
- Zabawki Rolly Toys
- Zabawki ProSin
- Zabawki SpinMaster
- Zabawki Tot Tutors
- Zabawki Dario
- Zabawki Invento
- Zabawki Estes
- Zabawki Air Wars
- Zabawki Radio Flyer
- Zabawki Pedalo
- Zabawki Millennium
- Zabawki Webley
- Zabawki Polly Pocket
- Zabawki AquaPlay
- Zabawki Teksta
- Zabawki Trigano-Jardin
- Zabawki Promedia
- Zabawki Triumph Sports
- Zabawki Bullet
- Zabawki Schleich
- Zabawki Propel
- Zabawki Elenco
- Zabawki Gel Blaster
- Zabawki Nils Fun
- Zabawki Nordic Play
- Zabawki Swurfer
- Zabawki Valley Dynamo
Najnowsze instrukcje dla Zabawki
13 Października 2024
13 Października 2024
11 Października 2024
10 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
Mega Bloks Despicable Me - Micro Action Figures Series 10 Instrukcja
9 Października 2024
Mega Bloks Buildable Minions Blind Packs Series III Instrukcja
9 Października 2024