Instrukcja obsługi York Fitness 1001

York Fitness Sprzęt fitness 1001

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla York Fitness 1001 (6 stron) w kategorii Sprzęt fitness. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/6

MODEL # 5020 PAGE 1

46/99

A S S E M B L Y I N S T R U C T I O N S

46/99

Home - Gym

1001

PAGE 2

46/99

ASSEMBLY INSTRUCTIONS

MODEL # 5020

22241

33B021

33B022

Home - Gym

1001

PAGE 3

46/99

NOTE: MAXIMUM WEIGHT STACK LIMIT 65KGS. (DO NOT

ADD EXTRA WEIGHTS) MAXIMUM WEIGHT OF USER = 100KG

Before assembly, read each section carefully. If these

instructions are followed exactly you will have no problems

with assembly.

Tools required: Slotted Screwdriver and 2 adjustable

Spanners or 7/16"(11mm) Spanner

1/2"(13mm) Spanner

9/16"(15mm) Spanner

5/8"(16mm) Spanner

Take upholstered piece and place upside down.

Place Pt.2205 on top of upholstery and put three x Pt.2290

(5/8" round tubing) through three large holes in Pt.2205 so that

the holes in the round tubing line up with holes in the

upholstery and Pt. 2205 is in the middle.

Insert six x 1/4"x 1 3/4" slotted screws through holes in

Pt.2290 and screw evenly into holes in the upholstery until

secured. Insert Pt.2235 into Pt.2205. Put one x 3/8" x 2" hex

head bolt through the hole in Pt.2235 and put one x 3/8" nyloc

nut on finger tight.

Assemble pulley wheel

in Pt.2205 as shown in (A)

using:

one x 3" pulley wheel

one x 3/8" washer

one x 5/16" hex nut

one x 3/8" x 13/16" stripper bolt

Pulley wheel should move freely

within bracket.

BAG75

Part No. Description Qty

33A03 1/4" Nyloc Nut 1

33A14 1/4" x 1 3/4" RHSMS 6

33A11 1/4" x 2" RHSMS 1

33A32 5/16" Hex Nut 1

41B400 1/4" Thread Cap 1

33A33 5/16" Nyloc Nut 1

33A51 3/8" Hex Nut 1

33A53 3/8" Nyloc Nut 4

33A48 3/8" x 2" H.H. Bolt 1

33A59 3/8" x 4 1/2" H.H. Bolt 2

33A45 3/8" x 13/16" Stripper Bolt 1

33A46 3/8" x 2" Stripper Bolt 1

33A421 3/8" x 4 1/4" Eye Bolt 1

33B63 3/8" SAE Washer 3

41B402 3/8" Thread Cap 1

41B07 1 1/4" SQ. Int. Cap (Black) 6

41B031 1 1/2" SQ. Int. Cap (Black) 4

41A83 Rubber Bumper 1

41A82 3" Pulley Wheel 1

41B211 Foam Cap 1" (Red) 4

41A81 31.75 IDx107.95mm Handgrip 2

BOX1

Part No. Qty.

Description

32B85 Bag 75 1

32B93 Bag 83 1

27E032 Foam Rollers 4

30E02 Upholstery 1001 1

21E2290 3

21E2202 1

21E2203 2

21E2205 1

21E2235 1

21E2229 1

21E2241 2

Attach finger tight two x Pt.2203 to Pt.2205 using:

two x 3/8" x 4 1/2" hex head bolts

and two x 3/8" nyloc nuts

Install four x 1 1/4" and one x 1 1/2" square internal caps.

Install one x round rubber bumper into Pt.2202 using

one x 1/4" x 2" slotted screw and one x 1/4" nyloc nut.

Take one x 4 1/4" eyebolt and screw on one x 3/8" hex nut until

it can go on no further. Insert eyebolt into back of Pt.2202 and

put on remaining one x 3/8" nyloc nut. Install thread cap.

Install remaining black caps into Pts.2202,2203,and 2205.

SECTION 1

Attach Pt.2202 to Pt.2205 as

in drawing B using:

one x 3/8" x 2" stripper bolt

one x 5/16" nyloc nut

two x 3/8" washers.

Leg curl must move freely

so do not over tighten

Insert two Pts.2241 into Pt.2202, slide on foam rollers and install

four large red foam caps into the tubing.

Now have someone sit on the bench while you tighten all the

remaining bolts. This will level the bench. Bolt in PT.2235 must

be tightened until it will not move inside Pt.2205.

Wet inside hand grips with warm soapy water and install on

Pt.2229.

Now open Box No.2 which contains the following parts:

BAG 27

Part No. Qty.

Description

33A03 1/4" Nyloc Nut 4

33A14 1/4" x 1 3/4" RHSMS 4

41A83 Rubber Bumper 4

BOX 2

Part No. Qty.

Description

32B37 Bag 27 1

32B86 Bag 76 1

32B87 Bag 77 1

32B88 Bag 78 1

21E2225 1

21E2227 1

21E2250 1

Locate Bag No.27 and check contents as listed :

Part No. Description

33A32 5/16" Hex Nut 2

33A45 3/8" x 13/16" Stripper Bolt 2

33B63 3/8" SAE Washer 2

41A82 3" Pulley Wheels 2

BAG 76

Turn Pt.2225 upside down and install the two pulley wheels

as you did before.

Put Bag 77, 78, and Pt. 2227 to one side.

Install Pts. from Bag 27 into

Pt.2225 as shown in C.

Locate Bag 76 and check contents as listed:

Qty.

Specyfikacje produktu

Marka:	York Fitness
Kategoria:	Sprzęt fitness
Model:	1001

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z York Fitness 1001, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Sprzęt fitness York Fitness

York Fitness Aspire 101 Instrukcja

23 Września 2024

York Fitness Aspire 120 Instrukcja

22 Września 2024

York Fitness Aspire 220 Instrukcja

22 Września 2024

York Fitness Aspire 420 Instrukcja

22 Września 2024

York Fitness Aspire 180 Instrukcja

22 Września 2024

York Fitness 1001 Instrukcja

19 Września 2024

Instrukcje Sprzęt fitness

Najnowsze instrukcje dla Sprzęt fitness

Tunturi Platinum Upper Body Instrukcja

15 Stycznia 2025

BH Fitness L290 Instrukcja

15 Stycznia 2025

HMS Premium KRM20 Instrukcja

14 Stycznia 2025

HMS Premium MGS02 Instrukcja

14 Stycznia 2025

True FS-70 Instrukcja

10 Stycznia 2025

True FS-100 Instrukcja

10 Stycznia 2025

True XFT-100 Instrukcja

10 Stycznia 2025

Body Solid GCLP100 Instrukcja

5 Stycznia 2025

Body Solid PAB139X Instrukcja

4 Stycznia 2025

Body Solid GFT100 Instrukcja

4 Stycznia 2025