Instrukcja obsługi Yardforce NX 80i


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Yardforce NX 80i (12 stron) w kategorii kosiarka. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/12
NX 60i / 80i/ 100i
ROBOTIC MOWER
Original Installation Guide
MÄHROBOTER
Original Installationsanleitung
ROBOSEKACKA
Originální instalační průvodce
ROBOT-TONDEUSE
Guide d’installation d’origine
ROBOTMAAIER
Originele handleiding
ROBOT KOSZĄCY
Oryginalna instrukcja
GB
DE
FR
NL
CZ PL
max.
8 m
min.
2 m
30 cm
30 cm
30 cm
30 cm
<
5 cm
A
< 10 cm
> 10 cm
1
GB
Description of product
1. STOP button
2. Ultrasonic sensor
3. Charging inlet
4. Rear wheel
5. Height adjustment dial
6. Control panel
7. Blade plate
8. Carry handle
9. Power switch button
Scope of delivery
Original
instrcution
Warranty
Installation
guide
Robotic Mower
Wire pegs
Manuals
Spare blades
Extension cord
Docking station
Connectors
Measurement ruler Boundary wire
Switching Power Supply
CONTENT
Description of the product .............................................1
Installation ..................................................................... 2
Operation ...................................................................10
Technical data ..............................................................14
Maintenance and storage .............................................15
Troubleshooting ............................................................17
GB
1
2
3
4
5
6
7
8
9
2 3
GB GB
Stones
We recommend clearing the lawn of small (less than 100 mm high) rocks and stones and any
stones with a round or sloped edge. The Robotic Mower might try and climb such rocks instead
of recognising them as a barrier. The Robotic Mower getting stuck on such a stone requires user
intervention to restart mowing. Contact with stones can result in damage to the blades.
Slopes
The Robotic Mower can navigate slopes up to a maximum of 40% incline or decline.
The boundary wire should never be perpendicular to an incline of more than 10%. Also, leave
strip of at least 2 m between a slope of 10% or steeper and the boundary wire. Otherwise, the
higher speed going down the slope may cause the Robotic Mower to go over the boundary wire,
especially on wet and slippery ground.
Paths, Driveways and Roads
If an elevated driveway crosses your lawn, better keep it outside the boundary wire.
Please allow a safety distance of 30 cm between driveway and boundary wire.
cm
If the driveway and lawn are at the same level, feel free to use the boundary wire to create a
corridor. This allows your Robotic Mower to cross the driveway and reach the opposite lawn.
30
Installation
Installation Guide
This chapter explains how to install the Robotic Mower. Please read this completely before you
start the installation.
Introduction
We recommend creating a drawing of your lawn, including all obstacles and how these should be
protected. This makes it easier to find a good position for the docking station and how to correctly
place the boundary wire around your garden perimeter protecting bushes, flower beds etc. You
will also need some tools, like a hammer and wire cutters, pliers or scissors.
Pre Cut your lawn
Your lawn needs to be prepared correctly, prior to installing the robot lawnmower.
Pre cut your lawn to a height of 60 mm.
Cutting limitations
The Robotic Mower is equipped with collision sensors. These detect all rigid and solid obstacles
that are higher than 100 mm, such as walls, fences and garden furniture.
When the sensors report an obstacle, the Robotic Mower stops, backs up and then mows in a
different direction. As a long-term solution, it is recommended to lay the boundary wire accordingly
using the ruler to protect obstacles and the device. Lay the boundary wire so that the Robotic
Mower is not more than 20 m away from the boundary wire at any point in the mowing area.
Trees
The Robotic Mower treats trees as common obstacles, but if the roots of the tree are exposed and
lower than 100mm, this area should be excluded using boundary wire in order to protect the tree
root, cutting blades or rear wheels from damage.
< 60mm
< 60 mm
> 60 mm
100 mm
min.
2
m
>10%
< 40%
> 40%


Specyfikacje produktu

Marka: Yardforce
Kategoria: kosiarka
Model: NX 80i

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Yardforce NX 80i, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje kosiarka Yardforce

Instrukcje kosiarka

Najnowsze instrukcje dla kosiarka

Hecht

Hecht 5564 SX Instrukcja

15 Października 2024
Craftsman

Craftsman 25365 Instrukcja

15 Października 2024
AL-KO

AL-KO Solo 4758 VSI Instrukcja

15 Października 2024
AL-KO

AL-KO Classic 4.64 SP-S Instrukcja

15 Października 2024
Gardena

Gardena PowerMax 36 A Li Instrukcja

15 Października 2024
Einhell

Einhell BG-PM 46 Instrukcja

14 Października 2024
Stihl

Stihl RMA 235 Instrukcja

13 Października 2024
Einhell

Einhell GC-PM 46 S Instrukcja

11 Października 2024
BaByliss

BaByliss Pro FX660E Instrukcja

11 Października 2024
Conair

Conair HC108RGB Instrukcja

9 Października 2024