Instrukcja obsługi Yamaha VXS3F

Yamaha głośnik VXS3F

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Yamaha VXS3F (2 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE

PROCEEDING

Please keep this manual in a safe place for future

reference.

WARNING

Always follow the basic precautions listed below

to avoid the possibility of serious injury or even

death from electrical shock, short-circuiting,

damages, fire or other hazards. These

precautions include, but are not limited to, the

following:

Do not open

• This device contains no user-serviceable parts. Do not

attempt to disassemble the internal parts or modify them

in any way. If it should appear to be malfunctioning,

discontinue use immediately and have it inspected by

qualified Yamaha service personnel.

Water warning

• Do not expose the device to rain, use it near water or in

damp or wet conditions. If any liquid such as water

seeps into the device, turn off the power of the amplifier

immediately. Then have the device inspected by

qualified Yamaha service personnel.

Hearing loss

• When turning on the AC power in your audio system,

always turn on the power amplifier LAST, to avoid

hearing loss and speaker damage. When turning the

power off, the power amplifier should be turned off FIRST

for the same reason.

Fire warning

• Do not place any burning items or open flames near the

device, since they may cause a fire.

If you notice any abnormality

• If any of the following problems occur, immediately turn

off the power of the amplifier.

- Unusual smells or smoke are emitted.

- Some object has been dropped into the device.

- There is a sudden loss of sound during use of the

device.

- Cracks or other visible damage appear on the device.

Then have the device inspected or repaired by qualified

Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below

to avoid the possibility of physical injury to you

or others, or damage to the device or other

property. These precautions include, but are not

limited to, the following:

Location

• Do not place the device in an unstable position where it

might accidentally fall over and cause injuries.

• Do not place the device in a location where it may come

into contact with corrosive gases or salt air. Doing so

may result in malfunction.

• Avoid being near the device during a disaster, such as

an earthquake. Since the device may fall and cause

injury, stay away from the device quickly and move to a

safe place.

• Before moving the device, remove all connected cables.

• Always consult qualified Yamaha service personnel if the

device installation requires construction work, and make

sure to observe the following precautions.

- Choose mounting hardware and an installation location

that can support the weight of the device.

- Avoid locations that are exposed to constant vibration.

- Use the required tools to install the device.

- Inspect the device periodically.

Connections

• Before connecting the device to other devices, turn off

the power for all devices. Also, before turning the power

of all devices on or off, make sure that all volume levels

are set to the minimum. Failing to do so may result in

electric shock, hearing loss, or equipment damage.

• Use only speaker cables for connecting speakers to the

speaker jacks. Use of other types of cables may result in

fire.

Handling caution

• Avoid use excessive force on the connectors to prevent

injuries.

• Do not operate the device if the sound is distorting.

Prolonged use in this condition could cause overheating

and result in fire.

• Avoid pulling the connected cables to prevent injuries.

• When choosing a power amplifier for use with this

device, make sure that the output power of the amplifier

is lower than the power capacity of this device. If the

output power is higher than the power capacity,

malfunction or fire may occur.

• Do not input excessively loud signals that may result in

clipping in the amplifier or cause the following:

- Feedback, when using a microphone

- Continuous and extremely loud sound from a musical

instrument, etc.

- Continuous and excessively loud distorted sound

- Noise caused by plugging/unplugging the cable while

the amplifier is turned on

Even if the output power of the amplifier is lower than the

power capacity of this device (program), damage to the

device, malfunction or fire may occur.

PA_en_7

NOTICE

To avoid the possibility of malfunction/ damage to the

product, damage to data, or damage to other property, fol-

low the notices below.



 Handling and maintenance

• Do not expose the device to excessive dust or vibration,

or extreme cold or heat (such as in direct sunlight or near

a heater), in order to prevent the possibility of panel dis-

figuration, unstable operation, or damage to the internal

components.

• When cleaning the device, use a dry and soft cloth. Do

not use paint thinners, solvents, cleaning fluids, or chem-

ical-impregnated wiping cloths.

• Condensation can occur in the device due to rapid,

drastic changes in ambient temperature—when the

device is moved from one location to another, or air con-

ditioning is turned on or off, for example. Using the

device while condensation is present can cause dam-

age. If there is reason to believe that condensation might

have occurred, leave the device for several hours without

turning on the power until the condensation has com-

pletely dried out.

• Be sure to observe the amplifier’s rated load impedance,

particularly when connecting speakers in parallel. Con-

necting an impedance load outside the amplifier's rated

range can damage the amplifier.

• Protection Circuit

This speaker system has an internal protection circuit

that shuts off the speaker unit when an excessive input

signal is applied. If the speaker unit emits no sound,

reduce the volume level of the amplifier immediately. The

sound will return automatically in several seconds.

• Do not place the speaker face down, as deformation of

the grille may result.

Information



 About this manual

• The illustrations as shown in this manual are for instruc-

tional purposes only.

• The company names and product names in this manual

are the trademarks or registered trademarks of their

respective companies.

Yamaha cannot be held responsible for damage

caused by improper use or modifications to the device.

Install the speakers onto wall/ceiling with the supplied brackets.

Ensure that the wall/ceiling is sufficiently strong.

The installation conditions between VXS3F/VXS3FW and VXS3FT/

VXS3FTW differ slightly. For installation instructions, refer to the

VXS3F/VXS3FW/VXS3FT/VXS3FTW Installation Guide.

Cable preparation

Strip the insulation of cables to be used as

shown in the figure and connect them.

Tap selector

(VXS3FT/VXS3FTW only)

Depending on the installation position of

the speaker, it may be impossible to set the

tap selector on the side of the bracket base.

In such a case, set the tap selector before

installing the bracket base.

1. Install the bracket gear to the speaker.

Use the supplied installation screws to attach the bracket gear.

The method for attaching the bracket gear depends on the orienta-

tion of the speaker (vertical or horizontal).

1. Make holes through the wall/ceiling for the bolts and cables, as

required, and feed the bolts and cables through them.

2. Install the bracket base onto the wall/ceiling.

VXS3F/VXS3FW

VXS3FT/VXS3FTW

For VXS3F/VXS3FW

1. Put the bracket cover on the bracket base.

2. Remove the Euroblock plug from the speaker system.

3. After loosening the terminal screws of the Euroblock plug with a

flat-blade screwdriver, insert the cable into each terminal and

tighten the screws. Make sure that the cables are secure and cannot

be pulled out.

For VXS3FT/VXS3FTW

1. After loosening the input screw on the terminal block with a Phil-

lips screwdriver, insert the cable into the terminal block and

tighten the screw. Make sure that the cables are secure and cannot

be pulled out.

2. Put the bracket cover on the bracket base and tighten it with

screws to secure the bracket cover.

3. Select the appropriate power tap by rotating the tap selector on the

side of the bracket base with a flat-blade screwdriver.

Illustration indicates the setting at 15 W for 100 V line and 7.5 W

for 70 V line.

1. Attach the safety wire to the wall/ceiling.

2. Attach the safety wire to the speaker.

3. Plug the Euroblock plug into the socket in the speaker.

4. Adjust the vertical angle and fix the bracket gear to the bracket

base by tightening with a Phillips screwdriver.

VXS3F/VXS3FW

VXS3FT/VXS3FTW

Installing the Speakers

CAUTION

Do not install brackets horizontally.

Incorrect Correct

Pre-installation

NOTE

• Use cables with a thickness up to AWG 12.

• Do not tin stranded wires by solder because doing so may cause the

wire to break.

1Attach the bracket gear

NOTE

• Determine the orientation for attaching the bracket gear by refer-

ring to the VXS3F/VXS3FW/VXS3FT/VXS3FTW Installation

Guide.

• When placing the speaker face down, place it on a soft cloth to

prevent damage to the grille.

2Install the bracket base onto the wall/

ceiling

NOTE

Determine the position of the holes by putting the bracket base onto

the wall/ceiling or confirming the dimensions.

NOTE

Make a half turn of the junction with the bracket gear as required.

7–8 mm

Tap selector

Bracket gear

M5-16mm

screw

Vertical installation Horizontal installation

Bracket base

Junction with the

bracket gear

NOTE

• If the cable gets in the way when installing, cut the cable tie. When

cutting the cable ties, be very careful not to cut the cables them-

selves by mistake.

• Connect the speaker cables before installing the bracket base, as

required.

3Connect the speaker cables

NOTE

Use a flat-blade screwdriver with a

blade less than 3 mm (0.1 in.).

CAUTION

When connecting speakers with high impedance, be sure that the

output total of each speaker does not exceed the rated output of

the power amplifier. For details, refer to the explanation of high-

impedance connection at the following URL.

Yamaha Pro Audio site: “Better Sound for Commercial Installations”:

http://www.yamahaproaudio.com/global/en/training_support/

better_sound/

If cables are connected in parallel to the subsequent speaker,

connect two cables to one terminal.

Bracket base

Junction with the

bracket gear

Cable tie

Bracket Cover

Euroblock plug

Power amplifier output (-)

Power amplifier output (+)

Speaker internal

connection

Speaker

Less than 3 mm (0.1 in.)

Power amplifier output (+) Power amplifier output (-)

Next speaker

Power amplifier

output

CAUTION

Make sure the amplifier is switched off before operating the tap

selector switch.

4Install the speaker onto the bracket

base

CAUTION

• Make sure to take appropriate measures to prevent the

speaker from falling down in the event of an installation fail-

ure.

• When installing the safety wire to the wall, install it higher

than the wire’s attachment point on the speaker, with as little

slack as possible.

• If the safety wire is too short, prepare another wire appropri-

ate for the speaker weight and installation conditions. If the

wire is too long, should the speaker fall, the wire may snap as

a result of excessive strain.

Bracket cover

M4-8mm screw

Safety wire

Euroblock plug

To the wall To the ceiling

Please check the included accessories.

Included Accessory

• Speaker × 2

• Bracket gear × 2

• M5-16mm screw (for speaker installation;

with washer) × 2

• Owner’s Manual

(this leaflet)

• Installation Guide

(English only)

VXS3F/VXS3FW

• Bracket base × 2

• Bracket cover × 2

VXS3FT/VXS3FTW

• Bracket base × 2

• Bracket cover × 2 • M4-8mm screw (for

fixing bracket cover)

× 2

• Safety wire × 2

*1: Full-space (4π)

*2: Pink noise (200 Hz–10 kHz)

*3: Calculated based on power rating and sensitivity, exclusive of power compression

* The contents of this manual apply to the latest specifications as of the printing date. To obtain the latest manual, access the

Yamaha website then download the manual file.

* The dimensions are shown on the reverse side of the Japanese manual.

Specifications

Model VXS3F/VXS3FW VXS3FT/VXS3FTW

Type Full-range, acoustic suspension type

Component 3.5 (9cm) cone driver

Coverage angle (-6 dB) Horizontal: 150°, Vertical: 160°

Rated impedance 8 Ω

100 V line:

670 Ω (15 W),

1.3 kΩ (7.5 W),

2.7 kΩ (3.8 W)

70 V line:

330 Ω (15 W),

670 Ω (7.5 W),

1.3 kΩ (3.8 W),

2.7 kΩ (1.9 W)

Power rating

NOISE 20 W —

PGM 40 W —

MAX 80 W —

Sensitivity

*1 86 dB SPL (1 W, 1 m) *2

Maximum SPL *3 105 dB SPL (1 m)

98 dB SPL (15 W, 1 m) *2

95 dB SPL (7.5 W, 1 m)

92 dB SPL (3.8 W, 1 m) *2

89 dB SPL (1.9 W, 1 m)

Frequency range (-10 dB) 130 Hz – 20 kHz

Connector

Euroblock (4 pin) × 1 (input: +/-,

loop-thru: +/-)

Max. wire size 12AWG (3.3 mm

Input terminal: screw type (4 × 4 con-

necter) × 1 (input: +/-)

Max. wire size 12AWG (3.3 mm

Transformer

Taps

70 V — 15 W, 7.5 W, 3.8 W, 1.9 W

100 V — 15 W, 7.5 W, 3.8 W

Overload protection Full-range power limiting for protecting network and transducers

Magnetically shielded No

Dust and water resistant —

Enclosure Cabinet VXS3F/VXS3FT: ABS (UL94-5VB), black

VXS3FW/VXS3FTW: ABS (UL94-5VB), white

Baffle ABS (UL94-5VB), black

Metal grille Powder coated perforated SPCC (t=0.8mm), aperture ratio: 55%

Outer color VXS3F/VXS3FT: Black (approximate value: Munsell N3)

VXS3FW/VXS3FTW: White (approximate value: Munsell N9)

Dimensions

(in horizontal

cabinet setup,

W × H × D)

speaker only 184 × 130 × 95 mm

(7 1/4" × 5 1/8" × 3 47/64")

with bracket, in

0 degree setup

184 × 130 × 134 mm

(7 1/4" × 5 1/8" × 5 9/32")

184 × 178 × 139 mm

(7 1/4" × 7 1/64" × 5 15/32")

Net weight speaker only 1.0 kg (2.2 lbs)

with bracket 1.1kg (2.4 lbs) 1.7kg (3.7 lbs)

Packaging Packaged in pair

SPEAKER SYSTEM

VXS3F/VXS3FW/VXS3FT/VXS3FTW

Owner’s Manual

ZT08430

Yamaha Pro Audio global website

http://www.yamahaproaudio.com/

Yamaha Downloads

http://download.yamaha.com/

(weee_eu_en_01)

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying documents means that used electri-

cal and electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collec-

tion points, in accordance with your national legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any

potential negative effects on human health and the environment which could otherwise arise from

inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local

municipality, your waste disposal service or the point of sale where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities

or dealer and ask for the correct method of disposal.

English

Auf der Rückseite befindet sich die deutsche Version der Bedienungsanleitung.

Specyfikacje produktu

Marka:	Yamaha
Kategoria:	głośnik
Model:	VXS3F

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Yamaha VXS3F, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje głośnik Yamaha

Yamaha WX-010 Instrukcja

15 Stycznia 2025

Yamaha DXR15 MKII Instrukcja

13 Stycznia 2025

Yamaha NS-F 51 Instrukcja

13 Stycznia 2025

Yamaha CMA3SW Instrukcja

9 Stycznia 2025

Yamaha IF2112/64 Instrukcja

9 Stycznia 2025

Yamaha IF2115/99 Instrukcja

9 Stycznia 2025

Yamaha VXC2FB Instrukcja

9 Stycznia 2025

Yamaha VXC6W Instrukcja

9 Stycznia 2025

Yamaha VXC2P Instrukcja

9 Stycznia 2025

Yamaha VXC8-VA Instrukcja

9 Stycznia 2025

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Bowers & Wilkins LCR3 Instrukcja

15 Stycznia 2025

Hifonics Vulcan VX6.2E Instrukcja

15 Stycznia 2025

Pyle PLRGSW64BK Instrukcja

15 Stycznia 2025

ION Insta Sound Instrukcja

15 Stycznia 2025

Pure Acoustics QBT-340 Instrukcja

15 Stycznia 2025

Polk REACT SOUND BAR 1 Instrukcja

15 Stycznia 2025

Sennheiser AMBEO Soundbar Plus SB02M Instrukcja

15 Stycznia 2025

Klipsch Reference RB-25 Instrukcja

15 Stycznia 2025

Klipsch Reference RB-35 Instrukcja

15 Stycznia 2025

Klipsch PIC-525-T-SC Instrukcja

15 Stycznia 2025