Instrukcja obsługi Yamaha SPS-80
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Yamaha SPS-80 (4 stron) w kategorii Dźwięk. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/4
English
E-1
Français
Deutsch
595 (23-7/16”)
297 (11-11/16”)
900 (35-7/16”)
650 (25-9/16”)
153 (6”)
47(1-7/8”) 6 (1/4”)
M4 (3/16”)
300 (11-13/16”)
●This speaker stand is only for the speaker systems listed
in “USABLE SPEAKERS” below. Do not use the
speakers other than these listed.
●To prevent the speaker from falling, use the screws and
parts provided with the stand.
●To prevent the speaker stand from falling over, select a
location which is flat and stable.
●To avoid accidents resulting from tripping over loose
speaker cables and to prevent the speaker stand from
falling over, fix the speaker cables to the wall, etc.
●Do not let the children lean on the stand as this might
cause the serious accidents resulting from the falling
over of the speaker stand.
PRECAUTIONS
Dimensions (W x H x D): 300 x 650 – 900 x 300mm
(11-13/16” x 25-9/16”
– 35-7/16” x 11-13/16”)
Weight: 2.1 kg (4 lbs. 10 oz.)
YAMAHA
●NX-230P
(the main and rear speakers included in the NS-P230/
NS-P236 speaker package)
●NX-220P
(the main and rear speakers included in the NS-P220
speaker package)
●NX-S80S
(the front and rear speakers included in the AVX-S80
sound system)
●NX-S60S
(the front and rear speakers included in the DVX-S60
sound system)
●NX-S77E
(the rear speakers included in the AV-S77 sound
system)
●NX-VS10E
(the rear speakers included in the VS-10 sound system)
* Use a speaker of 1 kg or less.
* Use a speaker with a screw hole of 4 mm in diameter
for attaching the speaker mounting bracket.
DIMENSIONS
SPS-80
SPEAKER STAND
Read this before setup
Thank you for selecting this YAMAHA SPS-80 speaker stand.
●To prevent the speaker stand from discoloring and
warping, keep the speaker stand away from the stoves
and places where it will be exposed to direct sunlight,
etc.
●Do not attempt to clean the speaker stand with chemical
solvents as this might damage the finish. Use a clean,
dry cloth.
●Secure placement or installation is the owner’s
responsibility.
YAMAHA shall not be liable for any accident caused
by improper placement or installation of speakers.
SETUP
INSTRUCTIONS
SPECIFICATIONS
USABLE SPEAKERS
Top view
Side view
(When shortened to minimum) (When extended to maximum)
(mm/inch)
SPS-80 ENG(02.6.17)b 02.6.19, 11:57 AM1
E-2
䡵SETUP PROCEDURES
(You will need a screwdriver for the setup.)
1
Attach the support to the base by fastening the
three + face screws from the holes on the bottom
of the base.
* Do not overtighten the + self-machine screws. Doing
so may damage the screws or assembly.
2
Pass the speaker cable through the support from
the bottom.
* A speaker cable more than 4 mm x 2 mm in diameter
cannot be used. If you use such a cable, connect it to
the speaker’s terminals without passing it through the
pole.
NAME QUANTITY
1Pole 2
2Support 2
3Base 2
4+ face screws 6
(Diam. x Length: 4 x 8 mm)
5Hexagon socket set screws 5
(Diam. x Length: 4 x 6 mm)
6Wrench (hexagonal) 1
7Cable protection seal 2
8Rubber cap 2
SETUP PROCEDURES
Before beginning the setup, check the parts list
and make sure all the parts are included.
3
Remove the speaker mounting bracket from the
pole by removing the screw using the screwdriver.
4
Attach the speaker mounting bracket to the
speaker by screwing it into the screw hole on the
bottom of the speaker.
5
Pass the speaker cable through the pole from the
end without the cut.
Then pass the cable through the hole on the
speaker mounting bracket from the side with the
groove as shown in the figure.
Base
Support
Speaker cable
(not included)
Speaker
(not included)
Support
Speaker
mounting
bracket
Pole
Speaker
mounting
bracket
Pole
Speaker cable
Cut
Groove
Name plate
Front
Back
SPS-80 ENG(02.6.17)b 02.6.19, 11:57 AM2
English
E-3
6
Pull out the speaker cable in the length of 15 to 16
cm from the speaker mounting bracket. Then attach
the speaker mounting bracket to the pole so that
the speaker cable fits to the cut in the pole. This
will lock the speaker cable. After that, fasten the
screw.
7
Insert the pole to the support, and adjust the height
of the stand. After adjusting the height, fasten the
hexagon socket set screws into the two holes on
the support using the longer handle of the included
wrench, and attach the rubber cap to the support.
* The line on the pole shows the limit of the stand
height. Do not let the line of the stand height limit go
beyond the upper end of the support. Otherwise, the
hexagon socket set screw of the lower side becomes
ineffective and the fixation becomes unstable.
8
Adjust the speaker direction. Then put the wrench
into the hole of the speaker monting braket, and
tighten the bracket to the speaker by moving the
wrench counterclockwise.
9
Connect the speaker cable to the speaker’s
terminals correctly.
* Refer to the instruction manual of the speakers for
connecting the speaker cables.
10
Align the speaker cable to the grooved part of
the bottom of the base, and fix the cable on the
base by putting the protection seal on it.
The setup has completed.
In the same way, set up the other stand.
Make sure to note the following when stretching or
shortening the pole after the setup.
●Make sure to remove the cable protection seal before
stretching or shortening the pole.
●When stretching the pole, pull out the pole carefully with
the speaker stand laying along.
●When shortening the pole, retract the pole carefully
while pulling out the speaker cable slowly by hand from
the base side with the speaker stand laying along.
Wrench
(hexagonal)
15–16 cm
* Rubber cap
Hexagon
socket set
screw
Stand height
limit
Support
Cable
protection
seal
Cut
* The inside of the rubber cap has a space for
storing the wrench after the setup.
Screw
SPS-80 ENG(02.6.17)b 02.6.19, 11:57 AM3
Specyfikacje produktu
| Marka: | Yamaha |
| Kategoria: | Dźwięk |
| Model: | SPS-80 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Yamaha SPS-80, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Dźwięk Yamaha
4 Lipca 2024
3 Lipca 2024
3 Lipca 2024
2 Lipca 2024
2 Lipca 2024
2 Lipca 2024
1 Lipca 2024
30 Czerwca 2024
28 Czerwca 2024
28 Czerwca 2024
Instrukcje Dźwięk
- Dźwięk Sony
- Dźwięk Logitech
- Dźwięk Philips
- Dźwięk Gigabyte
- Dźwięk JBL
- Dźwięk Roland
- Dźwięk Geemarc
- Dźwięk Nokia
- Dźwięk Bose
- Dźwięk Behringer
- Dźwięk Profoon
- Dźwięk Siemens
- Dźwięk DAP-Audio
- Dźwięk Kenwood
- Dźwięk Trust
- Dźwięk Focusrite
- Dźwięk Velleman
- Dźwięk Korg
- Dźwięk Zoom
- Dźwięk Cardo
- Dźwięk Sennheiser
- Dźwięk Jabra
- Dźwięk Samson
- Dźwięk Olympus
- Dźwięk ION
- Dźwięk TC Helicon
- Dźwięk NEC
- Dźwięk FiiO
- Dźwięk Advance Acoustic
- Dźwięk Fender
- Dźwięk AKG
- Dźwięk Power Dynamics
- Dźwięk Advanced Bionics
- Dźwięk Amplicom
- Dźwięk Alto Professional
- Dźwięk Reflecta
- Dźwięk Sony Ericsson
- Dźwięk Speedlink
- Dźwięk Envivo
- Dźwięk Aliph
- Dźwięk Sweex
- Dźwięk Phonak
- Dźwięk Mr Handsfree
- Dźwięk Gear4
- Dźwięk T-Mobile
- Dźwięk Bluetrek
- Dźwięk Starkey
- Dźwięk Iqua
- Dźwięk Bellman Symfon
- Dźwięk HUMANTECHNIK
- Dźwięk Griffin
- Dźwięk Plawa
- Dźwięk Native
- Dźwięk Inakustik
- Dźwięk Plextor
- Dźwięk Timewave
- Dźwięk Gioteck
- Dźwięk Nxzen
- Dźwięk MCS
- Dźwięk Velodyne
- Dźwięk Datel
- Dźwięk Bang Olufsen
- Dźwięk Bellman
- Dźwięk Konig Electronic
- Dźwięk Xqisit
Najnowsze instrukcje dla Dźwięk
14 Stycznia 2025
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024