Instrukcja obsługi WyreStorm EXF-300-H2

WyreStorm odbiornik EXF-300-H2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla WyreStorm EXF-300-H2 (4 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

In the Box

1x EXF-300-H2 Transmitter

1x EXF-300-H2 Receiver

1x Dual USB-A to Locking DC Power Plug

1x IR Emitter

1x IR Receiver (30KHz ~ 50KHz)

2x Male Phoenix Connector

4x Mounting Brackets

1x Quickstart Guide (This Document)

EXF-300-H2 Quickstart Guide | 180516

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features before beginning the

installation process.

Basic Wiring Diagram

Quickstart Guide

EXF-300-H2

4K 4:4:4 60Hz 18Gbps HDMI, HDCP 2.2 and

Bidirectional IR or RS-232 over OM3 Multi-Mode Fiber

KEY

HDMI

OM3 MM Fiber

IR/RS-232

Power

12v DC

Power Supply

OM3 Multi-Mode Fibre

300m/984ft Note: RS-232 and IR signals cannot be transmitted simultaneously over

OM3 if both are connected. Use either RS-232 or IR to avoid data conflicts.

EXF-300-H2

Transmitter

EXF-300-H2

Receiver

IR using CAB-IR-LINK

(Sold Separately)

HDMI HDMI IR

RS-232

HDMI Source

12v DC

Power Supply

Control System

EXF-300-H2 Quickstart Guide | 180516

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 4

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its

entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

OM3 Fiber SFP+ Guidelines

The EXF-300-H2 is designed to work with SFP+ OM3 MM ber cables providing a distance of 300m/984ft for all resolutions. This operation can be affected by

how the cables are terminated and routed within an installation. Care should be taken when terminating and routing based on the following guidelines.

• Fiber cable has a bend radius of 6.0cm/2.4in, when routing never exceed this radius as damage to the ber core can occur.

• Fiber core ends should be inspected for damage prior to terminating. Any scratches or blemishes can affect the performance of the connection.

• Never touch the end of the ber core with bare hands so that any oils or dirt can be transferred to the surface of the core.

• Refer to the guidelines and connection parameters from the ber cable manufacturer for more specic information regarding the cable being used.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on

signal transmission which may limit performance. Steps should be taken

to minimize or remove these factors completely during installation for best

results

• WyreStorm recommends using pre-terminated HDMI and DP cables due to

the complexity of these connector types. Using pre-terminated cables will

ensure that these connections are accurate and will not interfere with the

performance of the product.

IR TX/RX Guidelines

• Using WyreStorm infrared emitters and receivers is the best way to ensure

that most IR coding formats are transmitted and received Other 3rd party

emitters and receivers can be used; however, these devices must operate in

the same manner as the WyreStorm devices.

• Due to differences in IR across 3rd party control systems their IR ports

should never be connected directly to a NetworkHD system as an

incompatibility may exist. WyreStorm offers a cable that compensates for

voltage differences as well adjusts for differences in the pins used within

the port. Refer to the product page for more information.CAB-IR-LINK

IR TX Port Pinout

Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.

IR RX Port Pinout

Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs

+5V DC to power the included IR receiver.

RS-232 Wiring

The EXF-300-H2 uses a 3-pin RS-232 with no hardware ow control. Most

control systems and computers are DTE where pin 2 is RX, this can vary

from device to device. Refer to the documentation for the connected device

for pin functionally to ensure that the correct connections can be made.

3rd Party Device

Pin 1 TX (Transmit) > To > RX (Receive)--- ---

Pin 2 RX (Receive) > To > TX (Transmit)--- ---

Pin 3 G (Gro d) > To > G (Gro d)un --- --- un

WyreStorm Co ectornn

EXF-300-H2 Quickstart Guide | 180516

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

3 of 4

EDID Conguration

This extender uses EDID pass-through from the display to the source. No conguration is required for EDID settings.

Setup and Conguration

RS-232/IR Over Fiber

The EXF-300-H2 can transmit RS-232 or IR over ber bidirectionally, however it

can only send one or the other. The following settings must be made on both

the TX and RX for the type of signal that will be sent within the installation.

Send and Receive RS-232

Send and Receive IR

Troubleshooting

No or Poor-Quality Picture (snow or noisy image)

• Verify that power is being supplied to the transmitter and receiver.

• Verify that the ber cable is properly terminated.

• Verify that the output resolution of the source and display is supported by

this extender.

• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.

• Verify that all source and ber connections are not loose and are functioning

properly.

No or Intermittent 3rd party Device Control

• Verify that the RS-232/Ethernet cables are properly terminated.

• Verify that emitters/receivers are compatible with WyreStorm IR.

• If using an IR control system, verify that it is connected using the CAB-IR-

LINK cable.

Specyfikacje produktu

Marka:	WyreStorm
Kategoria:	odbiornik
Model:	EXF-300-H2
Kolor produktu:	Czarny
Wysokość produktu:	20 mm
Szerokość produktu:	150 mm
Głębokość produktu:	74.4 mm
Waga produktu:	400 g
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Technologia łączności:	Przewodowa
Certyfikaty:	FCC, CE
Maksymalne zużycie mocy:	4 W
Zakres temperatur (eksploatacja):	0 - 45 °C
Skrócona instrukcja obsługi:	Tak
Diody LED:	Tak
Zakres temperatur (przechowywanie):	-20 - 70 °C
Model:	Nadajnik i odbiornik AV
Prąd wyjściowy:	0.5 A
Maks. rozdzielczość:	4096 x 2160 px
HDCP:	Tak
Szerokość pasma:	18 Gbit/s
Maksymalny dystans transferu:	300 m
Obsługiwane rozdzielczości grafiki:	1920 x 1080 (HD 1080),3840 x 2160,4096 x 2160
HDMI in:	1
Zdalne wejście IR:	1
Obsługiwane tryby wideo:	1080p, 2160p
Uchwyty mocowania dołączone:	Tak
Zdanlne wyjścia IR:	1
Obsługiwane typy kabli:	Włókno
Porty wejściowe RS-232:	1
Porty wyjściowe RS-232:	1
Nadajnik podczerwieni w zestawie:	Tak
Odbiornik podczerwieni w zestawie:	Tak