Instrukcja obsługi Workzone 4.0 V Lithium-ion Cordless Screwdriver 44216

Workzone Niesklasyfikowane 4.0 V Lithium-ion Cordless Screwdriver 44216

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Workzone 4.0 V Lithium-ion Cordless Screwdriver 44216 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
Lithium- ion batteries. Help protect our environment and
conserve natural resources by contacting your local recycling center for
SERVICE INFORMATION F or technic al advice, r epair, or
genuin e replac ement parts, c all 1-800-840-7856
!
!
WARNING: Repairs should be made by an authorized repair center. Opening this tool
could invalidate your warranty.
NOTE: Due to continuous product improvement, we reserve the right to change the
product specification without prior notice.
GENERAL SAFETY RULES
WARNING : Read and understand all instructions.
or serious personal injury.
Save all warnings and instructions for future reference.
WORK AREA
• Keep work area clear and well lit. Cluttered benches and dark areas invite
accidents.
• Do not operate power tools in explosive atmospheres, such as in the
Power tools create sparks,
which may ignite the dust or fumes.
• Keep children, bystanders and visitors away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
• Power tools plug must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
• Avoid dy contact with earthed or grounded surfaces, such as pipes, bo
radiators, ranges and refrigerators.
• Do not expose power tools to rain or wet conditions.
• Do not bus thea e cord. Never seu the cord f c rying,or ar pulling or u u gnpl ggin
the power tool. Keep cord away from heat, oil, sharp edges or moving
parts. Replace damaged cords immediately. Damaged cords may create a
• Use only with model no. IVP0550-0400 charger. If operating a power tool
in a damp location is unavoidable, use a residual current device (RCD)
protected supply.
PERSONAL SAFETY
• Stay ert, watchal what you are doing n e co e a d us mmon s nse whe n pera o ting
a power tool. Do not use a power tool while you are tired or under the
A moment of inattention while
operating power tools may result in serious person injury.
• Use safety equipment. Always wear eye protection. Dust mask, non-skid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
• Remove any adjusting key or wrench before turning the power tool on.
• Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance enable better control of the tool in unexpected
situations.
• Dress properly. Do not wear loose clothing or jewellery. Contain long hair.
Keep your hair, clothing and gloves away from moving parts. Loose
clothes,jewelry, or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power tool for your application.
•
• Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, charging accessories, or storing
power tools.
• Store idle power tools out of the reach of children and other untrained persons.
Tools are dangerous in the hands of untrained users.
• Maintain power tools with care. Check for misalignment or binding of moving
operation. If damaged, have the power tools repaired before use.
• Keep cutting tools sharp and clean.
•
•
•
Use the power tool, accessories and tool bits etc. in a ordance with thesecc
instructions, taking into account the working conditions and the work to be
performed. A essories that may be suitable for one tool may create a risk of cc
injury when used on another tool.
SERVICE
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance Section of this manual. Use unauthorized parts or failure to
follow Maintenance Instructions may create a risk of shock or injury.
Working with the cordless screwdriver. (Attention! Before starting up the screwdriver,
familiarize yourself with its proper use by carefully read through the instructions
before use.)
SPECIFIC SAFETY RULES
•
Hold tool by insulated gripping surfaces when performing an operation where
the cutting tool may contact hidden wiring. Contact with a “live” wire will also
make exposed metal parts of the tool “live” and shock the operator.
The label on your tool may include the following symbols :
Figure 1
1. Forward/ Reverse rotating control
2. Chuck
3. Work light
4
5. Charging socket
6. Soft grip handle
7. Charger
8. Battery capacity indication
9. Battery capacity indication
10. Battery capacity indication
& Charging indicator
11. Battery capacity indication switch
12. Handle release button
. ON/OFF switch
GENERAL SPECIFICATION
Voltage DC 4V ：
No load speed 230rpm ：
Charger: Input AC100~ 240V, 50Hz/60Hz
Output DC 5.5V, 400mA
Charging time: Approx. 3-5 hours
Battery type: 3.7V 1300mAh Li-ion
INCLUDES:
• 4V S cr ewdriv er
• C
does not have the speed necessary to be used as a drill.
harge r
• Ins truction man ual
• Bits accessories:
1pc magnetic bits holder
3pcs 1in.(25mm) screwdriver bits: PH1, PH2, SL1/4”
2pcs HSS drill bits with hex shank: 5/64”, 3/32”
SCREWDRIVER BIT INSERTION
the bit into the screwdriver collet and ensure it is in all the way. The cordless
screwdriver ONLY accepts 1/4 in. hex-shaft screwdriver bits.
The cordless screwdriver should only be used as a screwdriver. attempt to DO NOT
use the tool as a drill using drill bits with 1/4 in. hex-shafts. The cordless screwdriver
WA RNING: C hanges or modic ations to this unit not
expressly approv ed by th e party responsi ble for
compliance could void the user’s authority to operate
the equipment.
NOTE: This equipment has bee n test ed and found to
comply with the limits for a Class B digital d evic e,
pursuant to Part 15 of the F CC Rules.
NOTE: This equipment h as bee n tested to be ETL
Approved.
Conforms to UL STD No.60745-1
No.60745-1 and 60745-2-2
THE RBRC TM SEAL The RBRCTM Seal (Rechargeable Battery Recycling
Corporation) on the lithium-ion battery (or battery pack) indicates that
the cost of recycling the battery or battery pack have already been paid by
Work Zone. In some areas, it is illegal to place spent lithium-ion batteries
in the trash or municipal solid waste stream and the RBRC program provides
an environmentally conscious alternative.
RBRC in coope tion with Work Zone and other battery users, has established ra
programs in the United States and Canada to facilitate the collection of spent
34
2
6
5
1
8
9
10
11
7
12
The screwdriver can be used extended or in “pistol grip” by adjusting the position of
the handle.
To change from straight to pistol grip, depress the handle release button and rotate
the handle of the unit anticlockwise until it clicks into position. To return to the
straight position, reverse the process.
You can press the battery charge display switch to show the battery capacity.
When the battery charge display lights up red the battery has less than 30% of its
capacity and should be charged.
Full power
Full power but will
require charging shortly
Needs charging
Green+Yellow+Red
Yellow+Red
Red
WARNING: Only us e recommended accessories - use of
unauthorized accessories can be hazardous and/or
result in injury or damage.
1. Plug the output cord of the charger into the socket as shown in Figure1
2. Plug the charger into standard electrical outlet.
OPERATING THE CORDLESS SCREWDRIVER Select the
the tip in the screwdriver collet and ensure it is in all the way. Insert the
screwdriver tip into the fastener and squeeze the reversible trigger. The
cordless screwdriver uses only one speed for all operations does not have the
capability for variable speeds.
Press the lower portion of the trigger to turn the screwdriver tip in a forward
(to the right) motion to install the fastener.
Press the upper portion of the trigger to turn the screwdriver tip in a reverse
(to the left) motion to remove the fastener.
MAINTENANCE AND CLEANING WARNING - No user
serviceable parts insid e.
reventive maintenance performed by unauthorized
personnel may result in mis placing of int ernal wires and
ponents which could cause serious hazard.
Never allow any liquid to get inside the tool and never allow any part of the
tool to become immersed in a liquid. TOOL LUBRICATION Your screwdriver has
been properly lubricated and is ready for use.
D.C. MOTORS The motor in your tool has been engineered for many hours of
mend
every six months. Only a genuine all trade replacement motor specially
designed for your tool should be used.
WARNING: To avoid accidents, always disconnect the
tool and/or charger from power supply before cleaning.
wear safety goggles when cleaning tools with compressed air.
Ventilation opening and switch and switch levers must be kept clean and free
of foreign matter. Do not attempt to clean by inserting pointed objects
through opening.
CAUTION-Certain cleaning agents and solvents damage
plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorin-
ated cleaning solvents, ammonia and household detergents that contain
ammonia.
CHARGER
WARNING
：Before using the AC battery charger unit, please read
carefully all instructions and cautionary markings on charger, battery
and product using battery.
Us ccompanie e e a only th charg r which e pd your roduct or
dir nt nu l. t tite eplac e mect r a e as list d in this m a Do o n subs ute
any tho e ger char r.
Do not disassemble charger. Do not use charger if it has
been damaged, left outdoors in the rain, snow, wet or damp
environments, or immersed in liquid.
When the battery requires recharging, a 3-5 hour charge allows the tool to operate
at full power. A charging indicator light on the charger will illuminate to show that
charging is taking place.
CHARGING THE SCREWDRIVER
The cordless screwdriver has a rechargeable state-of-the-art Lithium- ion
battery. The battery is charged with a charger that is plugged into the screwdriver
on the end side of the handle. The charging unit uses common prongs (both
prongs are the same) requiring no special polarized or grounded AC receptacles.
Both the charger unit and the plug are moulded that cannot be opened for repair.
To charge the battery on the cordless screwdriver, use the following steps:
NOTE
The internal battery is not fully charged.
requires 5-8 hours charge time to be fully charged. Subsequent recharging needs
3-5 hours for the battery to be fully charged.
Always recharge internal battery when tool performance
begins to diminish. Severe heat is most destructive to a battery; the more
heat generated, the faster the battery loses power. A battery that gets too hot can
have a shortened life.
Never over-discharge a battery by using the tool even after
tool performance has decreased. Do not attempt to discharge a tool’s
battery by continuing to pull on the tool trigger. When tool performance begins to
diminish, stop the tool and recharge the battery for optimal performance.
Charge internal battery at ambient temperatures between
+50°F(10°C)–95°F(35°C). Store tool and battery in locations
where temperatures will not exceed 120°F. This is important to
prevent serious damage to the battery cells.
com
P
18 19
17
16
15
14
13
12
11 10
9
8
3
4
7
6
5
2
1
20
21
22
24
25
26
27
28
29
30
31
33
38
39
34
35
36
37
32
40 41
42
43
44
45
23
27
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
first planet carrier
gasket for gear box
screw M2. 5
gear for motor
spring for press button
fixed piece for motor
motor
spring for switch button
forward/reverse control rod
protecive PCB
battery
DC socket
led light
screw
right main shell
screw
right ornament piece
right handle shell
charger
bit holder
25mm bit (SL1/4”)
25mm bit (PH1)
25mm bit (PH2)
3/32” hex shank twist drill
5/64” hex shank twist drill
bit coat
46
47
48
49
50
51
52
53
left handle shell
switch button
left ornament piece
left main shell
press button
power indicator
led cover
torque adjusting pin
torque adjusting piece 1
torque adjusting piece 2
locating piece
locating ring
torque spring
torque adjusting ring
torque indicate ring
torque adjusting cover
cover gasket
circlip for shaft
shaft
gasket for shaft
gear box
self-lock cylinder
self-lock piece
self-lock pin
second planet carrier
annular gear
planet gear
Li-ion
4.0 V Li-ION
CORDLESS
SCREWDRIVER
INSTRUCTION MANUAL
WITH PIVOTING HANDLE
FULL TWO YEAR HOME USE WARRANTY
Work Zone warrants this product for two years
against
Made in China / Hecho en China
DISTRIBUTED BY / DISTRIBUIDO POR:
ALDI INC. BATAVIA, IL 60510
www.aldi.us

Specyfikacje produktu

Marka: Workzone
Kategoria: Niesklasyfikowane
Model: 4.0 V Lithium-ion Cordless Screwdriver 44216

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Workzone 4.0 V Lithium-ion Cordless Screwdriver 44216, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Workzone

Workzone

Workzone WW 152 Instrukcja

3 Października 2024
Workzone

Workzone WW 154 Instrukcja

3 Października 2024
Workzone

Workzone WW 151 Instrukcja

3 Października 2024
Workzone

Workzone WZEN 20 Instrukcja

3 Października 2024
Workzone

Workzone BT-CK 18 2B-1,5 KIT Instrukcja

3 Października 2024
Workzone

Workzone WZ-HT 50-2 Instrukcja

3 Października 2024
Workzone

Workzone BT-CK 18 Li Instrukcja

3 Października 2024
Workzone

Workzone Multifunction Tool WMW 300-2 Instrukcja

16 Września 2024
Workzone

Workzone 4.0 V Lithium-ion Cordless Screwdriver 44216 Instrukcja

16 Września 2024
Workzone

Workzone 20V Li-Ion Circular Saw PT106401 Instrukcja

15 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024