Instrukcja obsługi Winland EnviroAlert EA-400
Winland
inteligentny dom
EnviroAlert EA-400
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Winland EnviroAlert EA-400 (4 stron) w kategorii inteligentny dom. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/4
Q S GUICK TART UIDE
© 2012 Winland Electronics, Inc.
D-011-0099 Rev (0 /201 )F 7 5
ALWAYS TEST THE YSTEM S
Test the system to ensure proper operation prior to leaving the job site To test the system, either change the probe’s .
temperature so it exceeds your limits, or change the limits to simulate an alarm. If a delay has been programmed, take the
delay out, test the unit, and then put the delay back in.
FREEZER OOLER ONITORING/C M
Never install the EnviroAlert console in a cooler or freezer (condensing environment). Instead, use a remote probe (TEMP-L-S
or TEMP-L-W) and program your zone accordingly. Extend the length of probe wiring up to 1,000’ (304.8m) using 22-18 AWG
twisted pair.
AVOIDING ALSE LARMS ON A F A COOLER OR REEZER F
Both the EA200 and EA400 offer an alarm delay from 0-120 minutes for each zone When a cooler or freezer door is opened, .
the temperature will rise and the probe will detect that rise. Freezers periodically need to enter a defrost cycle which may
also cause the temperature to rise above your limits. Set delays to avoid nuisance alarms under these normal circumstances.
We cannot advise you on what to set for delays or limits.
O -BN OARD TEMP ENSOR ONLY S (EA200 )
The EA200 has an on-board ambient temperature sensor and it is programmed on Zone 1.
More information and product manuals can be found at: www.winland.com
Tech Support 8:00am - 5:00pm Central Time
(800) 635-4269 • +1-507-625-7231 P
www.winland.com
STEP 1: CONNECT POWER AND PROBE(S)
Connect power to the PWR IN terminals, as shown in Figure 1. Be sure to observe proper polarity. Connect the probe(s) to the
zone(s) you intend to monitor. Extend the length of probe wiring up to 1,000’ (304.8m) using 22-18 AWG twisted pair.
EA200 NOTE: Zone 1 is dedicated for the on-board temperature sensor. Remote probes must be programmed on Zone 2.
There is only one input for a remote probe on the EA200 - this is Zone 2.
EA400 NOTE: The EA400 does not have an on-board temperature sensor and uses only remote probes.
STEP 2: UNLOCK CONSOLE FOR PROGRAMMING
To unlock the console, press and simultaneously release the ENTER and ALARM SILENCE buttons. The
“lock” icon should change to “unlocked”.
STEP 3: SET THE TIME AND DATE
Press the TIME/DATE button. Using either the INCREASE or DECREASE button, adjust the hours and then press the ENTER
button. Continue in this manner to set the minutes, AM/PM, year, month, and day. If power is lost, the time and date must
be reset.
STEP 4: PROGRAM THE ZONE(S)
1. Press the ZONE button. The active zone number will be flashing.
2. Select the zone you wish to program using INCREASE or DECREASE and then press ENTER. The “no”
means “not operational” and indicates the zone is currently off. Any zone not programmed should
be set to “no” and therefore turned off.
3. Based on the chart (Figure 2), select the proper sensor type using INCREASE or DECREASE and press ENTER.
Figure 1 - EA200 and EA400 Wiring
POWER REQUIREMENTS:
EA200-12: 11 to 14 VDC @ 120mA 11 to 14 VDC @ 200mAEA400-12:
EA200-24: 23 to 26 VDC @ 120mA 23 to 26 VDC @ 200mAEA400-24:
AUX OUT
Zone 1
PWR IN
PWR OUT
Z one 2
REMOTE PROBE INPUT
ALARM OUTPUTS
(On-Board
Sensor)
Zone 2
(External
Probe)
EA200
AUX OUT
Zone 1
Z one 2
Z one 3
Z one 4
PWR IN
PWR OUT
Z one 1
Zone 2
Zone 3
Z one 4
REMOTE PROBE INPUTS
ALARM OUTPUTS
EA400
Lock Unlock
4. Continue in this manner to set the
• high limit
• low limit
• optional time delay in minutes (this defaults to 0)
• non-alarm relay state (ENERGIZE/DE-ENERGIZE)
NOTE: If you are powering this device
from a system with battery back-up,
DE-ENGERGIZE (the default) generally
makes the most sense. If an alarm
is desired upon loss of power to the
EnviroAlert, select ENERGIZE. However,
the normally-open (N.O.) and normally-
closed (N.C.) contacts shown in Figure 1
will then be functionally opposite.
STEP 5: ALARM WIRING
You have the option of using the AUX
relay for all-in-one notification or using
the individual relay outputs. The AUX relay will change state when any zone is in alarm and can be cancelled for 10 minutes
using the ALARM SILENCE button. The individual outputs are not affected by the ALARM SILENCE button.
NOTE: If you are using the individual relay outputs, Output 1 corresponds to Zone 1; Output 2 corresponds to Zone 2; etc.
See Figure 1.
STEP 6: TEST THE SYSTEM
Test the system to ensure proper operation prior to leaving the job site. To test the system, either change the probe’s
temperature so it exceeds your limits, or change the limits to simulate an alarm. If a delay has been programmed, take the
delay out, test the unit, and then put the delay back in.
ADDITIONAL FEATURES
OFFSET button: The EnviroAlert has the ability to adjust the displayed temperature reading for each zone to match to
a known-good reference (±9 degrees). To use this feature, press the OFFSET button, choose which zone you wish to offset,
press ENTER, adjust the value of the offset, and then press ENTER again.
ALARM HISTORY button: This will display the most recent eight alarm events. The display will toggle between
the time and date. To scroll through the alarm events, use the INCREASE or DECREASE buttons. Press the ALARM HISTORY
button again to exit. This feature relies on the time and date being set correctly. To clear the alarm history, press and hold the
ALARM HISTORY button until you see “CLr”.
Probe Type Description
°C or °F Legacy (discontinued) polarity-sensitive temperature probes
1106, 1107, 1108, 1109, 1109A
Red °C or
Red °F
TEMP-H-S (32° to 300° F) and TEMP-H-W (32° to 221° F)
High-temperature range thermistor probes
Blue °C or
Blue °F
TEMP-L-S (-58° to 158° F) and TEMP-L-W (-58° to 158° F)
Low-temperature range thermistor probes
HA-III+ Humidity probe (5 to 95 % RH)
W-S-S and W-UC-S
Water detection probe (surface and under-carpet) supervised
Figure 2 - Remote Probe Selections
To insure proper operation, test weekly.
Specyfikacje produktu
| Marka: | Winland |
| Kategoria: | inteligentny dom |
| Model: | EnviroAlert EA-400 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Winland EnviroAlert EA-400, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje inteligentny dom Winland
7 Października 2024
Instrukcje inteligentny dom
- inteligentny dom Ikea
- inteligentny dom Tenda
- inteligentny dom Logitech
- inteligentny dom Xiaomi
- inteligentny dom TP-Link
- inteligentny dom Philips
- inteligentny dom Livoo
- inteligentny dom Acer
- inteligentny dom Bosch
- inteligentny dom Gigaset
- inteligentny dom Hikvision
- inteligentny dom Easy Home
- inteligentny dom Nobo
- inteligentny dom Origin Acoustics
- inteligentny dom Bose
- inteligentny dom EZVIZ
- inteligentny dom Panasonic
- inteligentny dom Theben
- inteligentny dom Crestron
- inteligentny dom Nedis
- inteligentny dom Nexa
- inteligentny dom Tesla
- inteligentny dom August
- inteligentny dom Niceboy
- inteligentny dom Ring
- inteligentny dom Imou
- inteligentny dom Blaupunkt
- inteligentny dom Vivax
- inteligentny dom ATen
- inteligentny dom Gardena
- inteligentny dom Evolveo
- inteligentny dom Honeywell
- inteligentny dom Strong
- inteligentny dom Audac
- inteligentny dom Cisco
- inteligentny dom Sanus
- inteligentny dom Trust
- inteligentny dom Cleanmaxx
- inteligentny dom TechniSat
- inteligentny dom V-TAC
- inteligentny dom Eufy
- inteligentny dom Krüger&Matz
- inteligentny dom Emos
- inteligentny dom Renkforce
- inteligentny dom Osram
- inteligentny dom Perel
- inteligentny dom Somfy
- inteligentny dom Netgear
- inteligentny dom DiO
- inteligentny dom Homematic IP
- inteligentny dom Totolink
- inteligentny dom Danfoss
- inteligentny dom Intertechno
- inteligentny dom Manta
- inteligentny dom NGS
- inteligentny dom Devolo
- inteligentny dom Gossen Metrawatt
- inteligentny dom Shelly
- inteligentny dom Edimax
- inteligentny dom AirLive
- inteligentny dom SPC
- inteligentny dom Brilliant
- inteligentny dom LevelOne
- inteligentny dom Digi
- inteligentny dom Oregon Scientific
- inteligentny dom Lorex
- inteligentny dom Aluratek
- inteligentny dom Abus
- inteligentny dom Elro
- inteligentny dom Hama
- inteligentny dom Eltako
- inteligentny dom Netatmo
- inteligentny dom Hager
- inteligentny dom Denver
- inteligentny dom CyberPower
- inteligentny dom Busch-Jaeger
- inteligentny dom Fibaro
- inteligentny dom Salus
- inteligentny dom EQ-3
- inteligentny dom Inkbird
- inteligentny dom Alecto
- inteligentny dom JUNG
- inteligentny dom Burg Wächter
- inteligentny dom X-Sense
- inteligentny dom Smartwares
- inteligentny dom RADEMACHER
- inteligentny dom Ajax
- inteligentny dom Brennenstuhl
- inteligentny dom Caliber
- inteligentny dom KlikaanKlikuit
- inteligentny dom Energenie
- inteligentny dom Steren
- inteligentny dom Hive
- inteligentny dom FireAngel
- inteligentny dom Chacon
- inteligentny dom Hombli
- inteligentny dom Naxa
- inteligentny dom Niko
- inteligentny dom Rain Bird
- inteligentny dom Veho
- inteligentny dom Gira
- inteligentny dom Ranex
- inteligentny dom Popp
- inteligentny dom Qnect
- inteligentny dom Fanvil
- inteligentny dom EQ3
- inteligentny dom REV
- inteligentny dom Sonoff
- inteligentny dom Meross
- inteligentny dom Home Easy
- inteligentny dom Chuango
- inteligentny dom ETiger
- inteligentny dom Swisstone
- inteligentny dom Drayton
- inteligentny dom Aqara
- inteligentny dom LSC Smart Connect - Action
- inteligentny dom MAC
- inteligentny dom Silvergear
- inteligentny dom Paulmann
- inteligentny dom Kogan
- inteligentny dom EKO
- inteligentny dom Airthings
- inteligentny dom Aeotec
- inteligentny dom Adurosmart
- inteligentny dom SEC24
- inteligentny dom Athom
- inteligentny dom Casambi
- inteligentny dom Tellur
- inteligentny dom TELE System
- inteligentny dom Iungo
- inteligentny dom Tjilla
- inteligentny dom SwitchBot
- inteligentny dom Mach Power
- inteligentny dom Blebox
- inteligentny dom Lutron
Najnowsze instrukcje dla inteligentny dom
13 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
7 Października 2024