Instrukcja obsługi WilTec HW-402B

WilTec nieskategoryzowany HW-402B

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla WilTec HW-402B (12 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
© by WilTec Wildanger Technik GmbH Seite 15
http://www.WilTec.de
http://www.aoyue.eu Version 4.2017
http://www.teichtip.de
Operation Manual
External Aquarium Filter
Modell HW-302/303/304/402B/403B/404B/403A/404A
ARTICEL
50197/50195/50193/50196/50194/50192/50358/50359
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignificant-
ly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities please contact us.
© by WilTec Wildanger Technik GmbH Seite 16
http://www.WilTec.de
http://www.aoyue.eu Version 4.2017
http://www.teichtip.de
The information contained in this document is subject to change without prior notice. No part of this
document can be copied or duplicated in another form without the prior written consent of WilTec Wil-
danger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liability for any errors in
this user manual or the connection diagram.
Although WilTec Wildanger Technik GmbH has made every effort to make sure that this user manual
is complete, accurate and updated, errors cannot always be avoided. In the event of problems with
this user manual please complete and send this form back to us.
FAX-notification (+++49 2403 55592-15),
from: ________________________________________
Name: ________________
Firm:_____________________
Tel/Fax:__________________
I would like to report the following mistakes:
___________________________________________________________________
Customer Service WilTec Wildanger Technik GmbH
e-mail: service@WilTec.info
Tel:++ +49 2403 55592-0
Introduction
Thank you for purchasing this quality product. To minimize the risk of injury by means of fire or
electric shock we urge that our clients take some basic safety precautions when using this
device. Please read the operation instructions carefully and make sure you have understood its
content.
Always use a grounded power connection with the appropriate mains voltage. You can find the corre-
sponding mains voltage on the type plate. If you have any doubts about the connection being ground-
ed, have it checked by a qualified professional. Never use a faulty electric cable.
Do not inspect the electrical part of the pressure pond filter in a wet or damp environment or when you
are wet yourself and protect it from direct sunlight. Install this device in a safe location so that nobody
can step on the cable, fall over or damage it. Disconnect the power plug before cleaning it and use
only a damp cloth for cleaning. Avoid using cleaning agents and make sure that no liquid enters the
electrical part of the pump.
The electric part of the device contains no parts that can be inspected or serviced by the user. Leave
the maintenance, adjustment and repair to qualified technical personnel. In case of unauthorised inter-
vention the 2-year warranty is no longer valid! Keep these operation instructions safe.
© by WilTec Wildanger Technik GmbH Seite 17
http://www.WilTec.de
http://www.aoyue.eu Version 4.2017
http://www.teichtip.de
Important Safeguards
220-240V AC, 50Hz, 15W/20W/50W IP44
Please read thoroughly before installation and operation
To guard against injury, basic safety precautions should be followed when handling the appliance, as
the following included:
1. The appliance is only for aquarium and indoor use.
2. To avoid possible electric shock, special care should be taken since water is employed in the
use of this appliance. Do not attempt to repair it by yourself. Return the appliance to the au-
thorized service facility for maintenance or discard it.
3. Make sure that your outlet voltage corresponds to the stated voltage on the rating label of the
pumps.
4. If the appliance is submerged into the water, DON’T reach for it! Please cut the power supply
FIRST and then fetch it.
5. Carefully examine the appliance after installation. It should not be plugged in if its electrical
components are wet.
6. Do not operate any appliance with a damaged cord or plug, or in abnormal state. The supply
cord of the appliance cannot be replaced. If the cord is damaged the appliance should be
scrapped.
7. Make sure that the electrical cord loops form a “Drip Loop” below the electrical outlet. The use
of a drip loop will help prevent any water leaks or splashes from running down the electrical
cord into your outlet. Instead of any water getting into your outlet it will simply drip off the cord
at the lowest point in the loop.
8. Close supervision is necessary when the appliance is used by or near children.
9. Always unplug the appliance when not in use, before putting on or taking off parts, and before
cleaning.
10. Do not install or store the appliance where it is exposed to moisture or to temperatures below
freezing.
11. Make sure the appliance is securely installed before operating it.
12. Read and observe all the instructions supplied with the appliance and on the appliance.
13. The pump must not be run dry.
14. Never use accessories which are not recommended by the appliance manufacturer. It may re-
sult in fire, electric shock and/or personal injury.
15. Use the appliance ONLY for domestic purposes and in the way indicated in these instructions
and place it in a dry environment.

Specyfikacje produktu

Marka: WilTec
Kategoria: nieskategoryzowany
Model: HW-402B

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z WilTec HW-402B, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje nieskategoryzowany WilTec

WilTec

WilTec 60045 Instrukcja

9 Września 2024
WilTec

WilTec 60044 Instrukcja

9 Września 2024
WilTec

WilTec 60583 Instrukcja

9 Września 2024
WilTec

WilTec 60042 Instrukcja

9 Września 2024
WilTec

WilTec 60586 Instrukcja

9 Września 2024
WilTec

WilTec 62453 Instrukcja

9 Września 2024
WilTec

WilTec 60585 Instrukcja

9 Września 2024
WilTec

WilTec HW-402B Instrukcja

31 Maja 2024
WilTec

WilTec HW-302 Instrukcja

31 Maja 2024
WilTec

WilTec HW-304 Instrukcja

31 Maja 2024

Instrukcje nieskategoryzowany

Najnowsze instrukcje dla nieskategoryzowany

Asko

Asko DBI644MIB.S.TW/1 Instrukcja

28 Października 2024
Asko

Asko DFS233IB.S.TW/1 Instrukcja

28 Października 2024
Emko

Emko EZM-9920 Instrukcja

27 Października 2024
Emko

Emko ESM-3712-H Instrukcja

27 Października 2024
Emko

Emko ATS-10 Instrukcja

27 Października 2024
Emko

Emko EAOM-11.2 Instrukcja

27 Października 2024
Emko

Emko EPM-3790 Instrukcja

27 Października 2024
Emko

Emko EPM-7790 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux IAN 108340 Instrukcja

27 Października 2024
Livarno Lux

Livarno Lux HG06009A-BS Instrukcja

27 Października 2024